Sharp MX-M266N / MX-M316N / MX-M356N Handy Guide ▷ View online
SHARP
TEST SIMULATION
33
23
Data Counter & Clear
2
Print jam/Trouble data print mode
80 Data print mode (paper feed)
81 Backup aper feed time data to USB memory
81 Backup aper feed time data to USB memory
24
Data Counter & Clear
1
Jam/trouble counter clear
2
Paper feed counter clear
3
Document feed & output counter clear
4
Maintenance counter clear
5
Developer counter clear
6
Copy Counter clear [Hidden as default]
9
Print & other counter clear [Hidden as
default]
default]
10 Fax counter clear [Hidden as default]
12 Document filing counter clear [Hidden as
12 Document filing counter clear [Hidden as
default]
15 Network scanner counter clear [Hidden as
default]
25 Pixel coverage counter clear
30 Initialise Administrator password
31 Initialise Service administrator password
35 Toner cartridge use status clear
30 Initialise Administrator password
31 Initialise Service administrator password
35 Toner cartridge use status clear
25
DV Auto Adjustment & Monitor
1
Main motor operation check
2
Auto developer adjustment setting
4
Toner supply correction data display
26
Device Configuration
1
Job separator tray setup
2
Paper size detection setting
3
Auditor setup
5
A3 Total/Maintenance counter set‐up
6
Destination set‐up
7
Machine ID setting
8
Counter mode setting (Long Paper)
10 Network scanner trial mode set‐up
18 Toner save operation enable/disable
30 CE mark control setup
32 Fusing cleaning operation setting
35 Trouble memory mode setting
38 Engine life over setting (Maintenance)
50 Function setting: (B/W reverse, Finisher,
18 Toner save operation enable/disable
30 CE mark control setup
32 Fusing cleaning operation setting
35 Trouble memory mode setting
38 Engine life over setting (Maintenance)
50 Function setting: (B/W reverse, Finisher,
Long Size print, Wireless set etc).
51 Serial port configuration setting (for PCI)
52 Blank paper count mode setting
56 Life correction ON/OFF
52 Blank paper count mode setting
56 Life correction ON/OFF
26
Device Configuration
65 Finisher staple alarm mode set‐up
69 Toner near end setting
73 Poster enlargement image loss adjustment
74 OSA Trial Mode setting
78 Remote operation (VNC) password set
79 User data pop up display enable/disable
69 Toner near end setting
73 Poster enlargement image loss adjustment
74 OSA Trial Mode setting
78 Remote operation (VNC) password set
79 User data pop up display enable/disable
27
FSS Setting
1
Set non‐detection of communication error
(U7‐00) with RIC.
(U7‐00) with RIC.
2
Sender's registration number and HOST
server telephone number setting
server telephone number setting
4
Initial call and toner order auto send set
5
Machine tag No. setting
6
Manual service call setting
7
Enable alert callout setting
9
Paper transport time recording, threshold
value & shading gain adjustment retry
number setting.
value & shading gain adjustment retry
number setting.
10 Trouble prediction history information clear
11 Check serial communication & scanner gain
11 Check serial communication & scanner gain
adjustment retry number history.
13 Check history of paper transport time
between sensors
14 FSS function connection test mode set
15 FSS connection status display
16 FSS alert send setting
17 FSS paper order alert setting
18 FSS paper feed retry counter clear
15 FSS connection status display
16 FSS alert send setting
17 FSS paper order alert setting
18 FSS paper feed retry counter clear
30
Sensor Operation & Test
1
Main unit sensor check
2
Tray sensor check (main)
40
Bypass Operation & Adjustment
2
Bypass tray width adjustment
7
Bypass tray width detection manual setting
41
OSS Operation & Adjustment
1
Document sensor operation check
2
Document sensor output setup
3
Document sensor output display
43
Fuser Setting & Adjustment
1
Fuser temperature setup for each mode
4
Fuser temperature 2 setup for each mode
10 Paper feed cycle timing set (postcard)
TEST SIMULATION
SHARP
34
43
Fuser Setting & Adjustment
20 Fuser temperature. correction for low
temperature & humidity (Sim43‐1)
22 Fuser temperature. correction for low
temperature & humidity (Sim43‐3)
44
Process Control Data
1
Process control mode setting
9
Process control operation 1 data display
14 Temp.& humidity output data
43 DV unit identification information display
43 DV unit identification information display
46
Copy & Image Density Adjustment
2
B/W copy density adjustment
4
Colour scanner density adjustment
5
B/W scanner density adjustment
8
Colour scanner balance adjustment RGB
9
SPF exposure adjustment
19 B/W auto exposure mode setup
30 Resolution adjust (sub‐scan – copy mode)
32 Document background density adjust.
37 B/W image create adjustment
39 Fax Image send sharpness adjustment
40 Fax mode exposure adjust (All modes)
41 Fax mode exposure adjust (Normal)
42 Fax mode exposure adjust (Fine Text)
43 Fax mode exposure adjust (Super Fine)
44 Fax mode exposure adjust (Ultra Fine)
45 Fax mode exposure adjustment (600dpi)
47 JPEG compression rate setting
60 Sharpness adjustment (colour auto mode)
61 Area separation recognition setting
62 ACS operating condition setting
63 Copy low density adjustment
30 Resolution adjust (sub‐scan – copy mode)
32 Document background density adjust.
37 B/W image create adjustment
39 Fax Image send sharpness adjustment
40 Fax mode exposure adjust (All modes)
41 Fax mode exposure adjust (Normal)
42 Fax mode exposure adjust (Fine Text)
43 Fax mode exposure adjust (Super Fine)
44 Fax mode exposure adjust (Ultra Fine)
45 Fax mode exposure adjustment (600dpi)
47 JPEG compression rate setting
60 Sharpness adjustment (colour auto mode)
61 Area separation recognition setting
62 ACS operating condition setting
63 Copy low density adjustment
48
Magnification & Motor Adjustment
1
Magnification ratio adjustment (Main & Sub
scan)
scan)
5
Magnification ratio adjustment (Sub scan
only)
only)
49
Firmware Upgrade
1
Firmware Upgrade Program
3
E Manual Update Program (Japan)
5
Watermark Update Program
50
Image Position Adjustment
1
Lead edge/copy position adjustment
5
Printer lead edge adjustment (sub scan)
6
SPF Lead edge/copy position adjustment
7
SPF Lead edge/copy adjustment value
10 Print off‐centre deviation adjustment.
12 Original centre deviation adjustment.
27 Image loss adjustment (Fax/Scanner)
28 Service adjustment (OC/SPF position)
12 Original centre deviation adjustment.
27 Image loss adjustment (Fax/Scanner)
28 Service adjustment (OC/SPF position)
51
Resist Roller Adjustment
1
Transfer current ON timing adjustment
2
Resist roller adjustment
9
Separation voltage ON/OFF timing
adjustment
adjustment
53
Document Feeder Adjustment
6
SPF document tray size adjustment
7
SPF document tray size adjustment value
set.
set.
8
SPF scanning position adjustment
9
SPF dirt detection setting
10 SPF dirt detection execution
55
MFP Data Setting
1
Engine soft switch setting
2
Scanner soft switch setting
3
Controller soft switch setting:‐
SW1‐5
Auto clear function before copy
job execution:‐
job execution:‐
0 =Disabled, 1 = Enabled
SW3‐6
Process mixed original size
printing for duplex mode:‐
printing for duplex mode:‐
0 =Disabled, 1 = Enabled
SW3‐7
HP Compatibility Mode:‐
0 =Disabled, 1 = Enabled
SW6‐1
Ethernet Speed Auto
negotiation:‐
negotiation:‐
0 = Enabled, 1 = Disabled
SW6‐2
Ethernet Link Speed:‐
0 = 100Base TX, 1 = 10Base T
SW6‐3
Ethernet Duplex Mode:‐
0 = Full, 1 = Half
SW6‐4
Ethernet 100/1000 Link Speed:‐
0 = 100Base TX, 1 = 1000Base T
SW9‐5
Maintenance notification setting
by Printer MIB:‐
by Printer MIB:‐
0 = Enabled, 1 = Disabled
SHARP
TEST SIMULATION
35
55
MFP Data Setting
3
Controller soft switch setting:‐
SW17‐3 A3 / Postcard Counter Mode
0 = Disabled, 1 = Enabled
SW18‐6 Hide Device Counter Clear
(SIM24‐6 to 24‐15)
0 = Hide, 1 = Display
SW22‐5 Display toner remaining status:‐
0= Disabled, 1 = Enabled/Display
SW24‐7 Continuous print mode for OSA
(job queuing for EAM):‐
0 = Job Queue Disabled
1 = Job Queue Enabled
1 = Job Queue Enabled
SW25‐7 Custom Envelope size (Printer).
0 = Disabled, 1 = Enabled
SW27‐8 Retain Scan to Desktop
destination for a certain period
after a scan operation.
after a scan operation.
0 = Disabled (Default)
1 = Enabled
1 = Enabled
SW28‐3 Single Email alert notification for
customer.
0 = Disabled (Default)
1 = Enabled
1 = Enabled
SW28‐4 Envelop mode – automatically
change to size tab screen.
0 = Disabled, 1 = Enabled
SW32‐2 Frequency to obtain remaining
toner information using MIB
0 = Every 25% (Default)
1 = Every 5%
1 = Every 5%
10 Special Stamp setting (Taiwan only)
56
MFP Data Import & Export
1
Transfer data execute (MFP/SD Card/SRAM
& EEPROM)
& EEPROM)
2
Export/Import EEPROM/SD Card & HDD
data
data
3
Document filing data backup to USB
4
Job log data backup to USB
5
Export Adjustment & Settings data to USB
6
Output Jam/Trouble data
7
Export Syslog data to USB
11 Save SD card data to HDD temporarily
12 Copy SD card data saved temporarily on
12 Copy SD card data saved temporarily on
HDD to machine
60
Memory Operation & Test
1
SDRAM read/write test (MFP PWB)
61
LSU Writing Adjustment/Test
1
LSU test (Polygon & BD detection check)
3
LSU power auto setup
62
HDD Operation & Test
1
HDD/SD Card format
2
HDD partial read/write check
3
HDD read/write check (all areas)
6
Smart (HDD) self‐diagnostic test
7
Smart (HDD) self‐diagnostic error log
8
HDD/SD Card format (excluding system &
operation manual area)
operation manual area)
10 Job completion list deletion (with job log)
11 Document filing data deletion
12 Enable/disable auto format for HDD trouble
13 HDD format (manual area only)
14 Delete document filing management data
11 Document filing data deletion
12 Enable/disable auto format for HDD trouble
13 HDD format (manual area only)
14 Delete document filing management data
63
CCD Operation & Adjustment
1
Shading correction data display
2
Shading correction execution (force)
3
CCD gamma & colour correction adjust.
4
SIT chart patch density list display
5
CCD gamma & colour correction reset.
64
Self Test Print
2
Test print (B/W mode)
4
Printer self print test
5
Printer self print test (PCL)
6
Printer self pint test (PS)
65
LCD Operation & Adjustment
1
LCD touch panel adjustment
2
LCD touch panel adjustment result display
5
Operation panel key input test
66
Fax Control Settings & Adjustments
1
Fax Soft SW setting
SW24
Communication Signal sending
level (bits 1‐8):‐
Default Value (Australia/NZ)
00001011
level (bits 1‐8):‐
Default Value (Australia/NZ)
00001011
SW27‐4
V.34 mode function (call
arrival):‐
0 = V.34 valid.
1 = V.34 invalid.
arrival):‐
0 = V.34 valid.
1 = V.34 invalid.
TEST SIMULATION
SHARP
36
66
Fax Control Settings & Adjustments
1
Fax Soft SW setting
SW27‐5
V.34 mode function (polling
when calling):‐
0 = V.34 valid.
1 = V.34 invalid.
when calling):‐
0 = V.34 valid.
1 = V.34 invalid.
SW27‐6
V.34 mode function (manual
communication):‐
0 = V.34 valid.
1 = V.34 invalid.
communication):‐
0 = V.34 valid.
1 = V.34 invalid.
SW33‐6,7 Transmission cable amplitude
equaliser:‐
00 = 0dB
01 = 4dB
10 = 8dB
11 = 12dB
00 = 0dB
01 = 4dB
10 = 8dB
11 = 12dB
2
Country code default set (Fax)
3
Fax PWB controller memory check
4
Fax signal line check (Max level)
5
Fax signal line check (Soft SW setting level)
6
Fax list print (confidential registration)
7
Fax memory printout (all data)
8
Fax sound message setup
9
Fax signal line check (Soft SW setting)
10 Fax all memory clear
11 Voice signal check (line/speaker 300bps)
12 Voice signal check (line/speaker 300bps)
13 Register dial number for Sim 66‐14/15/16
14 Adjust/check the time dial pulse (10bps)
15 Adjust/check the time dial pulse (20bps)
16 Adjust/check the send level DTFM signal
17 DTFM signal to send to line (Max level)
18 DTFM signal to send to line (Soft Sw level)
21 Print various registration information
22 Set the sound volume of the handset
24 Fast memory data clear
29 Fax address book clear
30 Tel/LIU sensor status check
31 ON/OFF setting of output port (Tel/LIU)
32 Received data check (comparison)
33 Busy Tone/CNG/CED/FNET detect check
34 Display time required for sending test data
36 Check Send/Receive from modem.
39 Check Destination saved in Fax EEPROM
42 Rewrite PIC program installed on Fax box
43 Write program & adjustment values to PIC
11 Voice signal check (line/speaker 300bps)
12 Voice signal check (line/speaker 300bps)
13 Register dial number for Sim 66‐14/15/16
14 Adjust/check the time dial pulse (10bps)
15 Adjust/check the time dial pulse (20bps)
16 Adjust/check the send level DTFM signal
17 DTFM signal to send to line (Max level)
18 DTFM signal to send to line (Soft Sw level)
21 Print various registration information
22 Set the sound volume of the handset
24 Fast memory data clear
29 Fax address book clear
30 Tel/LIU sensor status check
31 ON/OFF setting of output port (Tel/LIU)
32 Received data check (comparison)
33 Busy Tone/CNG/CED/FNET detect check
34 Display time required for sending test data
36 Check Send/Receive from modem.
39 Check Destination saved in Fax EEPROM
42 Rewrite PIC program installed on Fax box
43 Write program & adjustment values to PIC
installed on Fax
61 Display FAX related soft switch (151‐250)
62 FAX receive data export in PDF format.
62 FAX receive data export in PDF format.
67
Printer Settings & Adjustments
17 Printer NVRAM clear
45 Printer image filter and trapping
45 Printer image filter and trapping
adjustment.
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N service manuals if exist.