DOWNLOAD Sharp MX-M266N / MX-M316N / MX-M356N (serv.man6) Service Manual ↓ Size: 69.03 MB | Pages: 127 in PDF or view online for FREE

MX-M316N  SIMULATION  6 – 10

 

3-10

Adjustment

Used to adjust the finisher.

Finisher

1)

Select an adjustment target item with scroll key on the touch
panel.

2)

Enter the set value with 10-key.

3)

Press [OK] key. (The set value is saved.)

 

 

4-2

Operation test/check

Used to check the operations of the sen-
sors and detectors in the desk, and the
control circuit of those.

Desk

The operating conditions of the sensors and detectors are dis-
played.

The code names of the sensors and the detectors which are active
are highlighted.

 

4-3

Operation test/check

Used to check the operations of the loads
in the desk, and the control circuit of those.

Desk

1)

Select the load item that is required to operation check with the
touch panel key.

2)

Press [EXECUTE] key.

The selected load performs the operation.

When [EXECUTE] key is pressed, the operation is terminated.

A

FPAM ADJUST

Paper alignment width 
adjustment

40 - 60

50

When the adjustment value is increased, the 
width of the alignment plate F/R during 
alignment operation is decreased.
When the adjustment value is decreased, the 
width of the alignment plate F/R during 
alignment operation is increased.

0.419mm

B

FDRLM ADJUST

Paper exit roller descending 
position adjustment

40 - 60

50

When the adjustment value is increased, the 
descending position of the paper exit roller is 
shifted to the compression side.
When the adjustment value is decreased, the 
descending position of the paper exit roller is 
shifted to the decompression side.

0.13mm

C3PFD

Cassette 3 paper entry sensor

C3LUD

Cassette 3 paper upper limit sensor

C3PED

Cassette 3 paper empty sensor

C3SS

Cassette 3 installation sensor

DSW_C3

Cassette 3 door open/close sensor

C4PFD

Cassette 4 paper entry sensor

C4LUD

Cassette 4 paper upper limit sensor

C4PED

Cassette 4 paper empty sensor

C4SS

Cassette 4 installation sensor

DSW_C4

Cassette 4 door open/close sensor

CPFM

Desk motor

PTRC1

Desk vertical transport clutch

C3LUM

Cassette 3 lift-up motor

C3PUC

Cassette 3 paper feed clutch

C4LUM

Cassette 3 lift-up motor

C4PUC

Cassette 4 paper feed clutch

MX-M316N  SIMULATION  6 – 11

 

 

5-1

Operation test/check

Used to check the operation of the display,
LCD in the operation panel, and control cir-
cuit.

Operation panel

The LCD is changed as shown below.

The contrast changes every 2sec from the current level to MAX ->
MIN -> the current level. During this period, each LED is lighted.

The LCD display contrast change and the LED lighting status are
checked.

 

5-2

Operation test/check

Used to check the operation of the heater
lamp and the control circuit.

Fusing

1)

Select the item to be operation checked with the touch panel
key.

2)

Press [EXECUTE] key.

The selected heater lamp operates ON/OFF.

When [EXECUTE] key is pressed, the operation is terminated.

 

5-3

Operation test/check

Used to check the operation of the scanner
lamp and the control circuit.

Scanner (reading)

1)

Select the item to be operation checked with the touch panel
key.

2)

Press [EXECUTE] key.

The scanner lamp lights up for 10 sec.

When [EXECUTE] key is pressed, the operation is terminated.

 

 

6-1

Operation test/check

Used to check the operations of the load in
the paper transport system (clutches and
solenoids) and the control circuits.

Paper transport/Paper exit section

1)

Select the item to be operation checked with the touch panel
key.

2)

Press [EXECUTE] key.

The selected load performs the operation.

When [EXECUTE] key is pressed, the operation is terminated.

The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.

*1: If "Normal rotation" and "Reverse rotation" of a same load are

displayed as different items, when the both are selected at the
same time, "Normal rotation" is performed. In addition, a
change in the rotating direction is accepted only when the
operation is stopped.

HL_UM

Main heater lamp (Paper surface heat roller)

HL_US

Sub heater lamp (Paper surface heat roller)

SIMULATION

    NO.05-01

TEST

SIMULATION

NO.05-01

TEST

Transport/
process

MM

Main motor

POM_F*

1

Paper exit reverse motor (normal rotation)

POM_R*

1

Paper exit reverse motor (reverse 
rotation)

OSM

Shifter motor

PTRC2

Vertical transport clutch 2CS

RRC

PS clutch

PSPS

Process separation pawl solenoid

POGS1

Paper exit gate solenoid

POGS2

Right paper exit keep solenoid

Paper feed

C1LUM

Cassette 1 lift-up motor

C1PUC

Cassette 1 paper feed clutch

C2LUM

Cassette 2 lift-up motor

C2PUC

Cassette 2 paper feed clutch

MPFS

Manual feed take-up solenoid

MX-M316N  SIMULATION  6 – 12

 

6-2

Operation test/check

Used to check the operations of each fan
motor and its control circuit.

Others

1)

Select the item to be operation checked with the touch panel
key.

2)

Press [EXECUTE] key.

The selected load performs the operation.

When [EXECUTE] key is pressed, the operation is terminated.

The load operation is checked by the operation sound. However,
there are some loads which cannot be checked with the operation
sound.

 

6-90

Setting

Used to reset the machine to the factory
setting. (The scanner is set to the lock
enable position)

Scanner

1)

Press [EXECUTE] key.

The scanner is shifted to the lock enable position and stopped.

 

 

7-1

Setting

Used to set the operating conditions of
aging.

Others

1)

Select an item to be set with the touch panel key.

2)

Press [EXECUTE] key.

The machine is rebooted in the aging mode.

The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.

 

7-6

Setting

Used to set the operating intermittent aging
cycle.

1)

Enter the intermittent aging operation cycle (unit: sec) with 10-
key.

2)

Press [OK] key.

The time entered in procedure 1) is set.

* The interval time that can be set is 1 to 900 (sec).

The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.

 

7-8

Operation display

Used to display the warm-up time.

Press [EXECUTE] key.

Counting of the warm-up time is started and the time required for
warm-up is displayed

* Interruption of counting by pressing [EXECUTE] key is inhibited.

 

7-12

Operation test/check

The document reading number of sheets
setting (for aging operation)

RSPF

1)

Set document reading quantity with 10-key. 
(Setting range: 0 - 255)

2)

Press [OK] key. The set value is saved.

The aging operation condition set by this mode is maintained here-
after unless the power is turned off or the setting is changed.

PSFM

Power cooling fan motor

FUFM

Fusing fan motor

OZFM

Ozone fan motor

LSUFM

LSU fan motor

AGING

Aging operation setup

INTERVAL

Intermittent operation setting

MISFEED DISABLE

JAM detection ignoring setting

FUSING DISABLE

Fusing unit ignoring setting

WARMUP DISABLE

Warming up ignoring setting

DV CHECK DISABLE

Developing unit ignoring setting

SHADING DISABLE

Shading correction operation omitting setting

CCD GAIN FREE

CCD gain adjustment omitting setting

MX-M316N  SIMULATION  6 – 13

 

 

8-1

Operation test/check/adjustment

Used to check and adjust the operations of
the developing voltage in each print mode
and the control circuit.

Process (Developing)

1)

Select a mode with [TS_OFF] and [TS_ON] keys on the touch
panel.

2)

Select a target item to be adjusted with scroll keys.

3)

Enter the setting value with 10-key. (The value specified on the
label of the high voltage PWB must be entered.)

* When the 

   key is pressed, the setting value of each

item can be changed with 1up (1down) collectively.

4)

Press [EXECUTE] key.

The set value is saved and the voltage entered with step 3) is
output for 30 sec.

When [EXECUTE] key is pressed, the output is terminated.

 

8-2

Operation test/check/adjustment

Used to check and adjust the operation of
the main charger grid voltage in each
printer mode and the control circuit.

Process (Charging)

1)

Select a mode with [TS_OFF] and [TS_ON] keys on the touch
panel.

2)

Select a target item to be adjusted with scroll keys.

3)

Enter the adjustment value with 10-key. (The value specified
on the label of the high voltage PWB must be entered.)

* When the 

   key is pressed, the setting value of each

item can be changed with 1up (1down) collectively.

4)

Press [EXECUTE] key.

The set value is saved and the voltage entered with step 3) is
output for 30 sec.

When [EXECUTE] key is pressed, the output is terminated.

TS_
OFF

A

COPY 
DVB

Developing 
bias set value 
in a copy job 
(Toner save 
mode OFF)

0 - 650

400

400

430

B

PRINTER 
FAX DVB

Developing 
bias set value 
in a PRINT/
FAX job (Toner 
save mode 
OFF)

0 - 650

400

400

430

TS_
ON

A

COPY 
DVB

Developing 
bias set value 
in a copy job 
(Toner save 
mode ON)

0 - 650

320

320

320

B

PRINTER 
DVB

Developing 
bias set value 
in a print job 
(Toner save 
mode ON)

0 - 650

250

250

250

TS_
OFF

A

COPY GB

Charging/grid 
bias set value 
in a copy job 
(Toner save 
mode OFF)

0 - 750

575

575

605

B

PRINTER 
FAX GB

Charging/grid 
bias set value 
in a PRINT/
FAX job (Toner 
save mode 
OFF)

0 - 750

575

575

605

TS_
ON

A

COPY GB

Charging/grid 
bias set value 
in a copy job 
(Toner save 
mode ON)

0 - 750

495

495

495

B

PRINTER 
GB

Charging/grid 
bias set value 
in a print job 
(Toner save 
mode ON)

0 - 750

495

425

425

: ‘15/Aug.