Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man7) User Manual / Operation Manual ▷ View online
43
Part 2: Copier Operation
Pegasus-E_Copy_Ex.book 43 ページ ２００９年７月２２日 水曜日 午後２時４分
44
Pegasus-E_Copy_Ex.book 44 ページ ２００９年７月２２日 水曜日 午後２時４分
45
4
COPY FUNCTIONS
This chapter explains the basic procedures for making copies, including selection of the copy ratio and other copy
settings.
settings.
NORMAL COPYING
This section explains how to make a regular copy.
If "Auditing mode" has been enabled (page 23), enter your 5-digit account number.
If "Auditing mode" has been enabled (page 23), enter your 5-digit account number.
Copying from the document glass
1
Open the SPF and place the original
face down on the document glass.
face down on the document glass.
Align the upper left-hand corner
of the original with the tip of the
of the original with the tip of the
mark.
The original size is
automatically detected.
automatically detected.
2
Close the SPF.
After placing the original, be
sure to close the SPF. If left
open, parts outside of the
original will be copied black,
causing excessive use of toner.
sure to close the SPF. If left
open, parts outside of the
original will be copied black,
causing excessive use of toner.
3
Make sure that the desired paper tray
is selected.
is selected.
To load paper, see "LOADING PAPER" (page 18).
4
Set the number of copies.
An original up to A3 (11" x 17") can be
placed on the document glass.
placed on the document glass.
If the original is a non-standard size or the
size was not detected correctly, see
"SELECTING THE ORIGINAL SIZE" (page
50).
size was not detected correctly, see
"SELECTING THE ORIGINAL SIZE" (page
50).
Note
Note
• If the auto paper select function has been
disabled in the system settings (page 88),
use the [PAPER SELECT] key to select
the desired paper size.
use the [PAPER SELECT] key to select
the desired paper size.
• If you wish to use a size of paper different
from the size automatically selected by
the machine, use the [PAPER SELECT]
key to select the desired paper size.
the machine, use the [PAPER SELECT]
key to select the desired paper size.
• Paper in a different orientation from the
original can be selected if the auto paper
select or auto image function has been
selected. In this case, the image of the
original will be rotated.
select or auto image function has been
selected. In this case, the image of the
original will be rotated.
• To make a copy of a small original such as
a card, follow the procedure in "USING
THE BYPASS TRAY TO COPY A
SPECIAL SIZE ORIGINAL" (page 51).
THE BYPASS TRAY TO COPY A
SPECIAL SIZE ORIGINAL" (page 51).
• To use the bypass tray, select it manually.
If you are making two or more copies each
of multiple original pages, you can select the
sort function to collate the copies into sets.
(Page 64)
of multiple original pages, you can select the
sort function to collate the copies into sets.
(Page 64)
Ready to copy.
A4
100%
A4
100%
A4
AUTO
AUTO
Note
Note
Pegasus-E_Copy_Ex.book 45 ページ ２００９年７月２２日 水曜日 午後２時４分
46
COPY FUNCTIONS
5
Press the [START] key (
) to begin
copying.
The copy will be delivered to the
centre tray.
centre tray.
Copying from the SPF
1
Open the SPF and make sure that an
original has not been left on the
document glass. Gently close the SPF.
original has not been left on the
document glass. Gently close the SPF.
2
Adjust the original guides to the size
of the original(s).
of the original(s).
3
Place the original(s) face up in the
document feeder tray.
document feeder tray.
The original size appears in the
display and the most suitable
paper size is automatically
selected.
Insert the stack into the document
feeder tray until it stops.
display and the most suitable
paper size is automatically
selected.
Insert the stack into the document
feeder tray until it stops.
4
Set the number of copies.
5
Press the [START] key (
) to begin
copying.
The copies are delivered to the
centre tray.
The default output mode for
copying from the SPF is sort
mode. (Page 64)
The output mode can be
centre tray.
The default output mode for
copying from the SPF is sort
mode. (Page 64)
The output mode can be
changed using the automatic sort selection setting in
the system settings. (Page 87)
the system settings. (Page 87)
Stream feeding mode
If stream feeding mode has been enabled in the
system settings (page 87), the message "Set originals
for stream feeding." will appear in the display for 5
seconds after all originals have been fed from the SPF.
Any new originals placed in the SPF while this
message appears will be fed and copied automatically.
system settings (page 87), the message "Set originals
for stream feeding." will appear in the display for 5
seconds after all originals have been fed from the SPF.
Any new originals placed in the SPF while this
message appears will be fed and copied automatically.
MNO
WXYZ
@.-_
AD-END
• The centre tray can hold a maximum of
250 sheets (150 sheets when the job
separator tray kit is installed).
separator tray kit is installed).
• About one minute after copying ends,
"Auto clear" (page 18) activates and
restores the copy settings to the default
settings. The setting for "Auto clear" can be
changed in the system settings. (Page 83)
restores the copy settings to the default
settings. The setting for "Auto clear" can be
changed in the system settings. (Page 83)
• To cancel a copy job in progress, press
the [C] key.
• Differences in copy conditions may cause
the position of the printed copy image to
vary even the copies are of the same
original on the same paper. For more
information, see "Points concerning the
position of the printed copy image" on
page 47.
vary even the copies are of the same
original on the same paper. For more
information, see "Points concerning the
position of the printed copy image" on
page 47.
Note
• If the original is a non-standard size or the
size was not detected correctly, see
"SELECTING THE ORIGINAL SIZE"
(page 50).
"SELECTING THE ORIGINAL SIZE"
(page 50).
• If the auto paper select function has been
disabled in the system settings (page 88),
use the [PAPER SELECT] key to select
the desired paper size.
use the [PAPER SELECT] key to select
the desired paper size.
• To copy onto paper of a different size,
press the [PAPER SELECT] key and
select the desired paper size.
select the desired paper size.
• Paper in a different orientation from the original
may be selected if the auto paper select or
auto image function has been selected. In this
case, the image of the original will be rotated.
auto image function has been selected. In this
case, the image of the original will be rotated.
• To use the bypass tray, select it manually.
• Do not place originals of different sizes
• Do not place originals of different sizes
together in the document feeder tray. This
may cause misfeeds.
may cause misfeeds.
Note
• The centre tray can hold a maximum of
250 sheets (150 sheets when the job
separator tray kit is installed).
separator tray kit is installed).
• About one minute after copying ends,
"Auto clear" (page 18) activates and
restores the copy settings to the initial
settings. The duration of time after which
"Auto clear" clears the copy settings can
be changed in the system settings. (Page
83)
restores the copy settings to the initial
settings. The duration of time after which
"Auto clear" clears the copy settings can
be changed in the system settings. (Page
83)
• To stop copying in the middle of a run,
press the [C] key. If you find it difficult to
remove the original from the document
feeder tray, open the feeding roller cover
before removing the original. If you pull
out the original without opening the
feeding roller cover, the original may
become dirty.
remove the original from the document
feeder tray, open the feeding roller cover
before removing the original. If you pull
out the original without opening the
feeding roller cover, the original may
become dirty.
MNO
WXYZ
@.-_
AD-END
Note
Pegasus-E_Copy_Ex.book 46 ページ ２００９年７月２２日 水曜日 午後２時４分
Click on the first or last page to see other MX-M160 / MX-M160D / MX-M160DK (serv.man7) service manuals if exist.