Sharp MX-M160 / MX-M160D / MX-M160DK (serv.man7) User Manual / Operation Manual ▷ View online
35
2
REPLACING THE TONER CARTRIDGE
When the toner replacement icon (
) appears, little toner remains. Obtain a replacement cartridge as soon as possible.
When the message "
Add toner. Can not copy or print." appears in the display, the toner cartridge must be
replaced before copying can be resumed. Follow the steps below to replace the toner cartridge.
1
Open the front cover.
Push gently on both ends of the
front cover to open it.
front cover to open it.
2
Pull the toner cartridge out while
pressing on the toner cartridge lock
release lever.
pressing on the toner cartridge lock
release lever.
When pulling out the toner
cartridge, place your other hand
on the indentation of the
cartridge.
cartridge, place your other hand
on the indentation of the
cartridge.
3
Remove the new toner cartridge from
the bag. Grasp the cartridge on both
sides and shake it horizontally four or
five times.
the bag. Grasp the cartridge on both
sides and shake it horizontally four or
five times.
4
While pressing down on the toner
cartridge lock release lever, insert the
toner cartridge along the guides all
the way in.
cartridge lock release lever, insert the
toner cartridge along the guides all
the way in.
If there is any dirt or dust on the
toner cartridge, remove it before
installing the cartridge.
toner cartridge, remove it before
installing the cartridge.
5
Close the front cover.
The toner cartridge replacement
required icon (
required icon (
) will no longer
appear and copying will be
possible.
possible.
• During a long copy run or when copying originals with many dark areas, the message "Toner replenishment in
progress." may appear and copying will stop even though toner remains. The machine will feed toner for about
2 minutes. When the START indicator lights up, press the [START] key (
2 minutes. When the START indicator lights up, press the [START] key (
) to resume copying.
• When the toner cartridge replacement required icon (
) appears in the display, little toner remains and thus
copies may be faint.
Note
• After removing the toner cartridge, do not
shake it or tap it. Doing so may cause
toner to leak from the cartridge.
toner to leak from the cartridge.
• Put the old cartridge immediately in the
bag contained in the box of the new
cartridge.
cartridge.
• Do not throw the toner cartridge
into a fire. Toner may fly and cause
burns.
burns.
• Store toner cartridges out of the
reach of small children.
• Do not hold the cartridge by the shutter. It
may fall. Grasp the hand grip when
holding the cartridge.
holding the cartridge.
• Be sure to shake the cartridge only before
the tape is removed.
Toner cartridge
lock release lever
lock release lever
Caution
Warning
4 or 5 times
Caution
• Even after a new toner cartridge is
installed, the toner cartridge replacement
required indicator (
required indicator (
) may still appear,
indicating that copying cannot be resumed
(toner is not fed sufficiently). In this case,
open and close the front cover. The
machine will feed toner again for about two
minutes and then copying can be resumed.
(toner is not fed sufficiently). In this case,
open and close the front cover. The
machine will feed toner again for about two
minutes and then copying can be resumed.
• Before closing the front cover, make sure
that the toner cartridge is correctly
installed.
installed.
• When closing the front cover, gently hold
both ends.
Note
Pegasus-E_Copy_Ex.book 35 ページ ２００９年７月２２日 水曜日 午後２時４分
36
CHECKING THE TOTAL OUTPUT COUNT
To check the total number of pages output in copy, print, and fax modes and the total scan
count in scanner mode, hold down the [COPY] key when the machine is in the standby
state. The counts will appear while the key is held down. The total output count and the total
scan count can be used as a guideline for cleaning. When the total output count and the total
scan count exceed "999,999", the counts return to "0".
count in scanner mode, hold down the [COPY] key when the machine is in the standby
state. The counts will appear while the key is held down. The total output count and the total
scan count can be used as a guideline for cleaning. When the total output count and the total
scan count exceed "999,999", the counts return to "0".
• An A3 or 11" x 17" page is counted as two pages.
• Each two-sided sheet that is output is counted as two pages. (An A3 or 11" x 17" sheet is counted as four
• Each two-sided sheet that is output is counted as two pages. (An A3 or 11" x 17" sheet is counted as four
pages.)
• Blank copies and blank prints are included in the count.
• If the last page of a two-sided printing job is blank, it is not included in the count.
• If the last page of a two-sided printing job is blank, it is not included in the count.
DATA
ON LINE
PRINT
COPY
Note
Pegasus-E_Copy_Ex.book 36 ページ ２００９年７月２２日 水曜日 午後２時４分
37
2
CLEANING THE MACHINE
CLEANING THE DOCUMENT GLASS AND
SPF/DOCUMENT COVER
SPF/DOCUMENT COVER
If the document glass, SPF, underside of the document cover, or the scanner for originals coming from SPF (A) (the
long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies.
Always keep these parts clean.
long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies.
Always keep these parts clean.
Wipe with a clean, soft cloth. If necessary, moisten the cloth with water or a small amount of neutral detergent. When
finished, wipe dry with a clean cloth.
Do not use thinner, benzene, or similar volatile cleaning agents.
finished, wipe dry with a clean cloth.
Do not use thinner, benzene, or similar volatile cleaning agents.
Cleaning the original scanning glass (only when a SPF is installed)
If white or black lines appear in copies made with using the SPF, use the provided
glass cleaner to clean the original scanning glass. (If white or black lines appear in
copies, printed pages, or printed fax pages when the SPF is not used, see
"CLEANING THE TRANSFER CHARGER" on page 38.
glass cleaner to clean the original scanning glass. (If white or black lines appear in
copies, printed pages, or printed fax pages when the SPF is not used, see
"CLEANING THE TRANSFER CHARGER" on page 38.
1
Open the SPF and take out the glass
cleaner.
cleaner.
2
Clean the original scanning glass with
the glass cleaner.
the glass cleaner.
3
Return the glass cleaner to its original
position.
position.
CLEANING THE BYPASS TRAY PAPER FEED ROLLER
If misfeeds occur frequently when feeding postcards, envelopes, or heavy paper through the
bypass tray, wipe the surface of the paper feed roller with a soft, clean cloth dampened with
alcohol or water.
bypass tray, wipe the surface of the paper feed roller with a soft, clean cloth dampened with
alcohol or water.
Do not spray flammable cleaner gas. Gas from the spray may come in contact with the internal
electrical components or hot parts of the fusing unit, creating a risk of fire or electrical shock.
electrical components or hot parts of the fusing unit, creating a risk of fire or electrical shock.
(A)
Warning
Example of dirty print
Black lines
White lines
Paper feed roller
Pegasus-E_Copy_Ex.book 37 ページ ２００９年７月２２日 水曜日 午後２時４分
38
TROUBLESHOOTING AND MAINTENANCE
CLEANING THE TRANSFER CHARGER
If white or black lines appear in copies or the image is blotchy, the transfer charger may be dirty. Follow the steps
below to clean the charger.
below to clean the charger.
1
Turn the power switch off.
2
Open the bypass tray and the side
cover.
cover.
3
While lifting the handle, gently pull out
tray 1.
tray 1.
4
Take out the charger cleaner.
5
Place the charger cleaner on the
transfer charger and gently slide the
cleaner in the direction indicated by
the arrow two or three times.
transfer charger and gently slide the
cleaner in the direction indicated by
the arrow two or three times.
If the sheet metal on the
transfer charger is smudged
with toner, wipe it with a soft,
clean cloth.
transfer charger is smudged
with toner, wipe it with a soft,
clean cloth.
6
Return the charger cleaner to its
original position.
original position.
7
Close the tray and side cover.
8
Turn the power switch to the "ON"
position.
position.
Charger
cleaner
cleaner
Slide the charger cleaner from one end to
the other end along the groove of the
transfer charger. If the cleaner is stopped it
reaches the other end or if the direction of
movement is reversed, smudges may
appear on copies.
the other end along the groove of the
transfer charger. If the cleaner is stopped it
reaches the other end or if the direction of
movement is reversed, smudges may
appear on copies.
Note
Pegasus-E_Copy_Ex.book 38 ページ ２００９年７月２２日 水曜日 午後２時４分
Click on the first or last page to see other MX-M160 / MX-M160D / MX-M160DK (serv.man7) service manuals if exist.