Sharp MX-6580N / MX-7580N (serv.man2) Handy Guide ▷ View online
SHARP
CONSUMABLES
13
FUSING SECTION:
Product Code
Description / Contents
Approx. Life
MX-751FB
Fusing Belt Kit:-
• Fusing belt.
• Meandering suppress collar x 2.
• Wave washer x 2
• Meandering suppress collar x 2.
• Wave washer x 2
300k
MX-751HK
Fusing Roller Kit:-
• Fusing roller.
• Fusing roller bearing x 2
• Heat roller.
• Heat roller bearing x 2
• Insulation bush x 2
• Fusing roller bearing x 2
• Heat roller.
• Heat roller bearing x 2
• Insulation bush x 2
300k
MX-750LH
Pressure Roller Kit:-
• Pressure roller.
• Pressure roller gear.
• Pressure roller bearing x 2.
• Lower separation pawl x 5.
• Lower separation pawl spring x 5.
• 24T gear
• Pressure roller gear.
• Pressure roller bearing x 2.
• Lower separation pawl x 5.
• Lower separation pawl spring x 5.
• 24T gear
300k
MX-620WB
Web Cleaning Kit:-
• Web roller.
• Web guide shaft.
• Web pressure roller.
• Web pressure roller bearing x 2
• Web guide shaft.
• Web pressure roller.
• Web pressure roller bearing x 2
300k
PERIPHERALS
MX-SCX1
Saddle Staple Cartridge (for MXFN22)
5000 staples (x 3)
MX-SCX2
Staple Cartridge (for MXFN21/MXFN22)
5000 staples (x 3)
AR-SC2
Staple Cartridge (for MXFN19/MXFN20)
5000 staples (x 3)
AR-SC3
Saddle Staple Cartridge (for MXFN20)
2000 staples (x 3)
AR-SV1
Stamp Cartridge (for AR-SU1)
2 cartridges
SERVICE ROTATION:
MX-751U1
Primary Transfer Belt Unit
For Service Rotation
MX-751U2
Secondary Transfer Belt Unit
MX-752FU
Fusing Unit (230V) for EU
Note:
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.
The consumable life may vary, depending on the document density, temperature, humidity and machine
operation.
INITIAL SETUP
SHARP
14
DEVELOPER SETUP:
Sim 25-02
Auto Developer Adjustment - Select CMYK.
Toner Installation must be performed after Auto Developer Adjustment is completed.
* For optimum image quality & performance, it is recommended to setup & install
developer at the customer site.
developer at the customer site.
Clean LSU Dust Proof Glass.
TONER INSTALLATION & REPLENISHMENT:
Install CMYK Toner Cartridges:
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode during
Initial Toner Replenishment.
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode during
Initial Toner Replenishment.
PRODUCT ACTIVATION & FIRMWARE UPGRADE:
Activation of Optional Products:
System Settings – Common Settings – Product Key.
Sim 22-05 Check Firmware Version(s):
Upgrade to latest version.
INITIAL SETUP:
Sim 26-01
Right Exit Tray Installation: Yes/No.
Sim 26-02
LCC Installation (Paper Size): A4/Letter.
Sim 26-06
Machine Destination check.
Sim 26-35
Set Multi Error Counter: Set to 1 (Multi Count).
Sim 26-50
Long Paper Support (up to 1300mm): 0 = Disable, 1 = Enable.
Sim 26-52
Non Printed Paper Counter Set-up.
Sim 55-03
Process Mixed Size Pages (orientation) when Printing in Duplex:
SSW 3-6, 0 = Disable, 1 = Enable.
Sim 55-03
PDF/PS Preview Thumbnail for Direct Print Function:
SSW 34-3, 0 = Disable, 1 = Enable.
Add PANTONE® Colour LUT
(Subject to Availability)
Service WebPage – Output Profile Settings – Spot Colour Table Settings;
Upload PANTONE® LUT for MX-6580/7580N series.
Keyboard Language Setting (For Embedded & Optional Keyboard):
System Settings – Common Settings – Keyboard Settings – Default Keyboard Setting.
Paper Size & Type Settings:
System Settings – Common Settings – Paper Tray Settings.
Set cassette size by adjusting the guides in the cassette.
Adjust Date/Time (Inc. Daylight Saving setting):
System Settings – Common Settings – Clock Adjust.
SHARP
INITIAL SETUP
15
PRINT IMAGE POSITION & BK MAGNIFICATION:
Check Print Image Off Centre & Lead Edge position - Use Sim 50-10:-
• Inside dimension of the printed halftone must be 240±0.5mm.
• Lead edge void area 4.0 ± 1.0mm.
• Rear edge void area 2.0mm - 5.0mm.
• Front & Rear Void areas 2.0 ± 2.0mm.
• Lead edge void area 4.0 ± 1.0mm.
• Rear edge void area 2.0mm - 5.0mm.
• Front & Rear Void areas 2.0 ± 2.0mm.
If NG, perform the following adjustments as required:-
Manual Adjustment:
Sim 50-10
BK MAG / Image Off Centre Adjustment (All Trays).
Sim 50-05
Printer Lead Edge & Void Adjust.
IMAGE SKEW & COLOUR REGISTRATION
Sim 50-22
Colour Registration/Skew & OPC Drum Phase Adjustment:
Check/Adjust SKEW (CMY) so value is Close to 0 as possible (Result=OK).
HALFTONE COLOR CALIBRATION
Sim 46-74
Engine & Printer Colour Calibration:
Select FACTORY Mode.
IMAGE QUALITY CHECK [COPY & PRINT]
Check Image Quality – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:
F/R Evenness Adjustment:
Sim 61-13
F/R Evenness Correction Data Clear
Sim 61-11
F/R Evenness Correction Adjustment
Note: Sim 46-74 must be executed after F/R adjustment is performed.
Copy Density Manual Adjustment:
Sim 46-01
Copy Density Adjust. (Colour).
Sim 46-02
Copy Density Adjust. (B/W).
Sim 46-09
SPF Copy Density Adjust.
Print Image Manual Adjustment (Lead Edge, Void, Off Centre etc.):
Sim 48-01
Magnification Adjustment (OC & SPF).
Sim 50-01
Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12
OC & SPF Off Centre Adjust.
Check Print Image Quality:
Sim 64-05
PCL Density Test Page
Sim 64-06
PS Density Test Page
INITIAL SETUP
SHARP
16
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX-FX15
Sim 66-02
Fax SW Setting (Destination).
Sim 66-10
Fax Memory Clear.
Sim 66-39
Fax Destination Setting.
FINISHER OPTION – MX-FN19/20/21/22
Sim 03-10
Saddle Fold/Staple Position Adjustment [MX-FN20/22 only]
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode (ON/OFF).
Limit the number of sets loaded in the saddle staple (ON/OFF).
**Limit load of folded paper on paper exit and limit load on 50-sheet
Staple saddle finisher are set in SADDLE COPIES.
FOLDING UNIT – MX-FD10
Z Fold Skew Adjustment check.
EXTERNAL ACCOUNTING MODULE – MX-AMX3
Sim 55-03
Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03
Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06
Data Simulation Print
Device Clone & Storage Backup
Sim 56-01
Backup EEPROM Data to HDD
Click on the first or last page to see other MX-6580N / MX-7580N (serv.man2) service manuals if exist.