Sharp MX-6500N / MX-7500N (serv.man2) Handy Guide ▷ View online
Initial Set-up
17
Document Solutions After Sales Service
Laser Power Correction
SIM 61-11
Manual Correction
front – rear image density variation
PRINT IMAGE MAGNIFICATION & OFF CENTRE
SIM 50-28
Automatic Adjustment:
BK MAG ADJUST (Magnification)
SETUP/PRINT ADJ (Offset)
Normally no need to adjust as set in factory
COPY IMAGE POSITION & VOID
Automatic Adjustment:
SIM 50-28
OC ADJUST (Platen)
SPF ADJUST
Normally no need to adjust as set in factory
RSPF & DSPF IMAGE POSITION & VOID
Automatic Adjustment:
SIM 50-28
OC ADJUST (Platen)
SPF ADJUST
Normally no need to adjust as set in factory
HALF-TONE - COLOUR CALIBRATION
Copy/Engine:
SIM 46-74
Automatic Colour Calibration
Please refer to Page 12 for Calibration Procedure.
This Must Be Completed In Full
Initial Set-up
18
Document Solutions After Sales Service
FAX OPTION (MX-FX11)
SIM 66-02
Fax SW Setting (Destination)
SIM 66-39
Fax Destination Set
SIM 66-10
Fax Memory Clear (For Standard Extended Memory)
MFP Status Display
SIM 55-03
Toner Remaining Status Display
SSW22, Data/Bit 5 (Change from 0-1)
MFP Counter Display
SIM 55-03
Larger Than A3 Copy Count Status
Display
SSW17, Data/Bit 3 (Change from 0-1)
Product Activation & Firmware
Activation of Optional Products:
System Settings – Administrator Mode – Product Key
SIM 22-05
Check Firmware version – Upgrade to latest version.
OTHER
SIM 22-06
Print All Simulation Data
System Settings
Adjust Clock (Set Time, Time Zone &
Date)
Device Clone & Storage Backup
Backup System Settings, Scan
Destinations, User Control, OSA
Configuration after customer
installation is complete.
Colour Calibration
19
Document Solutions After Sales Service
Automatic Colour Calibration
-
FACTORY MODE
When adjusting colour balance before or after routine maintenance, always use the
recommended paper (Mondi 90gsm or equivalent) for optimum image quality.
1. Always ensure the latest firmware is installed on the copier, this can be visually checked using
SIM22-05 or printing the data sheet using SIM22-06.
2. Check that A/E settings and manual colour calibration settings are set to default (page 4 of SIM22-
06 data sheet)
3. Ensure all maintenance work is carried out, checking maintenance counters in SIM22
4. Ensure optics cavity is clean and clean laser slit glass
5. Perform SIM61-11
,
front – rear image density variation (auto correction) ADJ 23A
6. Next perform black image density sensor adjustment in SIM44-02, refer to ADJ 3B in service
manual
7. Perform image skew adjustment and registration adjustment using SIM50-22. When performing
skew adjustment follow procedure in ADJ 5 in service manual
8. Execute SIM44-27, halftone process control correction data clear
9. Execute SIM44-06, Process control correction (force)
10. Execute SIM44-26, halftone process control correction execution
11. Perform colour balance adjustment SIM46-74, place printed pattern on to glass for both engine
and printer modes
Engine Calibration Pattern Check Patch image Printer Calibration Pattern
Check patch Image
Note
Colour Calibration
20
Document Solutions After Sales Service
12. After performing the colour calibration press “OK”, the initial setting of the half tone calibration
will be performed
13. Wait until “EXECUTE” key is displayed, and then press it
14. Once “COMPLETED THIS PROCEDURE” is displayed, the adjustment operation is completed.
Cancel SIM46-74.
The adjustment results only become valid when both engine and printer adjustments have been
completed in full, if the simulation is cancelled after just the engine calibration is performed the
adjustment result is invalid.
completed in full, if the simulation is cancelled after just the engine calibration is performed the
adjustment result is invalid.
Click on the first or last page to see other MX-6500N / MX-7500N (serv.man2) service manuals if exist.