Sharp MX-6201N / MX-7001N (serv.man19) Service Manual ▷ View online
MX-7001N SIMULATION 7 – 41
* Sensor A and sensor B On
→ On : Possibly caused by slip in
paper transport.
Off
Off
→ Off: The sensor actuator response trouble can be
detected.
27-14
Purpose
Setting
Function (Purpose) Used to set the FSS function connection
mode. (Only "Disable
→ Enable" is
allowed.)
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: Disable (Default)
0: Disable (Default)
1: Enable
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
30
30-1
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in other than the
paper feed section and the control circuits.
paper feed section and the control circuits.
Section
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
SPPD2
SPPD3
On
→ On
C4
Off
→ Off
C5
SPPD3
SPPD4
On
→ On
C6
Off
→ Off
C7
SPPD4
SPPD5
On
→ On
C8
Off
→ Off
C9
SPPD5
SPOD
On
→ On
CA
Off
→ Off
CB
Sensors A
Sensors B
Status
Cord between sensors
Bk
Color
Heavy
paper
SIMULATION NO.27-13
TEST
TROUBLE PRECOGNITION RESULT(FEED TIME)
CLOSE
DATE
SENSOR CODE PASS TIME STANDARD TIME
F
EED TIME1
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME2
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME3
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME4
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME5
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME6
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME7
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME8
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME9
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME10
: 99/99/99 99:99:99
99999
99999
99999
FEED TIME1(SPF) : 99/99/99 99:99:99
99999
99999
99999
FEED TIME2(SPF) : 99/99/99 99:99:99
99999
99999
99999
FEED TIME3(SPF) : 99/99/99 99:99:99
99999
99999
99999
FEED TIME4(SPF) : 99/99/99 99:99:99
99999
99999
99999
FEED TIME5(SPF) : 99/99/99 99:99:99
99999
99999
99999
FEED TIME6(SPF) : 99/99/99 99:99:99
99999
99999
99999
FEED TIME7(SPF) : 99/99/99 99:99:99
99999
99999
99999
1/2
A:
A : 0
;
CONNECTION TEST MODE(1:ON 0:OFF)
SIMULATION NO.27-14
FSS TEST MODE SETUP
0
0
1
OK
TEST
CLOSE
PPD1
Registration pre-detection
PPD2
Registration detection
POD1
Fusing after-detection
POD2
Main unit paper exit detection
POD3
Right tray paper exit detection
TFD
Main unit paper exit full detection
TFD_R
Right tray paper exit full detection
DSW_R
Right door open/close detection
DSW_D
Front cover open/close detection D
DSW_FU
Front cover open/close detection U
DSW_FL
Front cover open/close detection L
VTOD
Vertical transport path open/close detection
DHPD_K
K phase detection
DHPD_C
C phase detection
DHPD_M
M phase detection
DHPD_Y
Y phase detection
TNFD
Waste toner full detection
TBBOX
Waste toner installation detection
CCHP
Charger cleaner HP detection
CCM_ROT
Charger cleaner rotation detection
LPPD
LCC transport sensor
T2PPD
Tray 2 transport detection
T1PPD1
Tray 1 transport detection 1
T1PPD2
Tray 1 transport detection 2
FUEXD
Fusing external variation sensor
WEB_INL
Fusing web initial detection
WEB_END
Fusing web end detection
PTCM_HP
PTC cleaner HP detection
TBLTC
Transfer belt separation sensor CL
TBLTB
Transfer belt separation sensor BK
THPS
Secondary transfer separation home position sensor 1
FIN SENSOR CHECK
CLOSE
SIMULATION NO.30-01
TEST
1/1
PPD1
PPD2
POD1
POD2
POD3
TFD
TFD_R
DSW_R
TNFD
TBBOX
CCHP
COM LOT
DSW_D
DSW_FU
DSW_FL
VTOD
DHPD_K
DHPD_C
DHPD_M
DHPD_Y
LPPD
T2PPD
T1PPD1
T1PPD2
FUEXD
WEB_INL
WEB_END
PTCM_HP
TBLTC
TBLTB
THPS
MX-7001N SIMULATION 7 – 42
30-2
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in the paper feed
section and the control circuits.
section and the control circuits.
Section
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
33
33-1
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the card
reader sensor and the control circuit.
Section
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
40
40-2
Purpose
Adjustment/Setting
Function (Purpose) Manual paper feed tray paper width detec-
tor detection level adjustment
Section
Paper feed
Operation/Procedure
1)
1)
Set the manual paper feed guide to the maximum width (MAX).
2)
Press [EXECUTE] key.
The maximum width (MAX) detection level is recognized.
The maximum width (MAX) detection level is recognized.
3)
Set the manual paper feed guide to the P1 width (A4).
4)
Press [EXECUTE] key.
The P1 width (A4) detection level is recognized.
The P1 width (A4) detection level is recognized.
5)
Set the manual paper feed guide to the P2 width (A4R).
6)
Press [EXECUTE] key.
The P2 width (A4R) detection level is recognized.
The P2 width (A4R) detection level is recognized.
7)
Set the manual paper feed guide to the minimum width (MIN).
8)
Press [EXECUTE] key.
The minimum width (MIN) detection level is recognized.
The minimum width (MIN) detection level is recognized.
If the above procedures are not properly performed, "ERROR" is
displayed. If properly performed, "COMPLETE" is displayed.
displayed. If properly performed, "COMPLETE" is displayed.
MPED
Manual paper feed paper empty detection
MPLD1
Manual feed paper length detection 1
MTOP1
Manual feed tray reduction detection
MTOP2
Manual feed tray extension detection
MPFD
Manual paper feed paper entry detection
TANSET
Tandem tray installation detection
T1SPD
Tandem tray 1 paper remaining quantity detector
T1LUD
Tandem tray 1 upper limit detector
T1PED
Tandem tray 1 paper presence
T2SPD
Tandem tray 2 paper remaining quantity detector
T2LUD
Tandem tray 2 upper limit detector
T2PED
Tandem tray 2 paper presence
C3SS1
Tray 3 rear edge detection 1
C3SS2
Tray 3 rear edge detection 2
C3SS3
Tray 3 rear edge detection 3
C3SS4
Tray 3 rear edge detection 4
C3PFD
Tray 3 paper entry detection
C3LUD
Tray 3 lift HP detection
C3PED
Tray 3 paper empty detection
C3SPD
Tray 3 paper remaining quantity detection
C4SS1
Tray 4 rear edge detection 1
C4SS2
Tray 4 rear edge detection 2
C4SS3
Tray 4 rear edge detection 3
C4SS4
Tray 4 rear edge detection 4
C4PFD
Tray 4 paper entry detection
C4LUD
Tray 4 lift HP detection
C4PED
Tray 4 paper empty detection
C4SPD
Tray 4 paper remaining quantity detection
TRAY3 LEN
Tray 3 guide plate position
TRAY3 AD
Tray 3 paper width detection volume output
TRAY SENSOR CHECK(MAIN) TRAY3_LEN: **** TRAY3_AD: ***
CLOSE
SIMULATION NO.30-02
TEST
1/1
C3PFD
C3LUD
C3PED
C3SPD
MPED
MPLD1
MTOP1
MTOP2
MPFD
TANSET
T1SPD
T1LUD
T1PED
T2SPD
T2LUD
T2PED
C3SS1
C3SS2
C3SS3
C3SS4
C4SS1
C4SS2
C4SS3
C4SS4
C4PFD
C4LUD
C4PED
C4SPD
CARD
Card presence detection
DATA
Card number signal detection
CLOCK
Reference clock signal detection
MAX POSITION
Manual feed maximum width
P1 (A4) POSITION
Manual feed P1 position width (A4)
P2 (A4R) POSITION
Manual feed P2 position width
MIN POSITION
Manual feed minimum width
CARD READER SENSOR CHECK
CLOSE
SIMULATION NO.33-01
TEST
1/1
CARD
DATA
CLOCK
MX-7001N SIMULATION 7 – 43
40-7
Purpose
Adjustment/Setting
Function (Purpose) Used to adjust the manual paper feed tray
width detection level.
Section
Paper feed
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
40-12
Purpose
Adjustment/Setting
Function (Purpose) Used to perform the tray 3 paper width
detection level adjustment.
Section
Paper feed
Operation/Procedure
1)
1)
Set the tray 3 paper guide to the maximum width (MAX).
2)
Close the tray 3.
3)
Press [EXECUTE] key.
The maximum width (MAX) detection level is recognized.
The maximum width (MAX) detection level is recognized.
4)
Set the tray 3 paper guide to the minimum width (MIN).
5)
Close the tray 3.
6)
Press [EXECUTE] key.
The minimum width (MIN) detection level is recognized.
The minimum width (MIN) detection level is recognized.
If the above procedures are not properly performed, "ERROR" is
displayed. If properly performed, "COMPLETE" is displayed.
displayed. If properly performed, "COMPLETE" is displayed.
41
41-1
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the docu-
ment size sensor and the control circuit.
Section
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
41-2
Purpose
Adjustment
Function (Purpose) Used to adjust the document size sensor
detection level.
Section
Operation/Procedure
1)
1)
Open the document cover, and press [EXECUTE] key without
any document on the document table.
The sensor level without document is recognized.
any document on the document table.
The sensor level without document is recognized.
2)
Set an A3 (11 x 17) paper on the document table, and press
[EXECUTE] key.
The sensor level with a document is recognized.
[EXECUTE] key.
The sensor level with a document is recognized.
When the above operation is completed, it is displayed.
Item
Default
value
A
MAX POSITION
Manual feed maximum width
241
B
P1 (A4) POSITION
Manual feed P1 position width
(A4)
(A4)
231
C
P2 (A4R) POSITION
Manual feed P2 position width
140
D
MIN POSITION
Manual feed minimum width
19
SIMULATION NO.40-02
TEST
BYPASS TRAY ADJUSTMENT
CLOSE
EXECUTE
MAXPOSITION ADJUSTMENT.
PRESS [EXECUTE] TO START
A : 241
;
MAX POSITION
B : 231
;
P1(A4) POSITION
C : 140
;
P2(A4R) POSITION
D : 19
;
MIN POSITION
A:
SIMULATION NO.40-07
BYPASS TRAY VALUE SETTING
241
0
255
OK
TEST
CLOSE
OCSW
Document cover status
Open: Normal display
Close: Highlighted
Close: Highlighted
PD1 - 7
Document detection
sensor status
sensor status
No document: Normal display
Document present: Highlighted
Document present: Highlighted
SIMULATION NO.40-12
TEST
TRAY3 ADJUSTMENT
CLOSE
EXECUTE
MAXPOSITION ADJUSTMENT.
PRESS [EXECUTE] TO START
PD SENSOR CHECK
CLOSE
SIMULATION NO.41-01
TEST
1/1
OCSW
PD1
PD2
PD3
PD4
PD5
PD6
PD7
SIMULATION NO.41-02
TEST
DOCUMENT SIZE PHOTO-SENSOR SETUP
EXECUTE
CLOSE
WITH THE ORIGINAL COVER OPENED, TURN ON THE EXECUTE
KEY WITH THE ORIGINAL ON THE ORIGINAL TABLE.
KEY WITH THE ORIGINAL ON THE ORIGINAL TABLE.
MX-7001N SIMULATION 7 – 44
41-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the docu-
ment size sensor and the control circuit.
Section
Operation/Procedure
The detection output levels (A/D value) of OCSW and the docu-
ment detection sensors (PD1 to PD7) are displayed in real time.
The range of PD1 to PD7 light reception (A/D value) is 1 to 255.
(128: Default)
The detection output levels (A/D value) of OCSW and the docu-
ment detection sensors (PD1 to PD7) are displayed in real time.
The range of PD1 to PD7 light reception (A/D value) is 1 to 255.
(128: Default)
43
43-1
Purpose
Setting
Function (Purpose) Used to set the fusing temperature in each
mode.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
Item
Default value
62-sheet
machine
machine
70-sheet
machine
machine
A
HL_UM READY
Upper thermistor main
set value when ready
standby
set value when ready
standby
190
200
B
HL_LM READY
Lower thermistor main
set value when ready
standby
set value when ready
standby
140
145
C
HL_US READY
Upper thermistor sub set
value when ready
standby
value when ready
standby
160
170
D
HL_EX READY
External thermistor set
value when ready
standby
value when ready
standby
210
215
E
HL_UM PLAIN
PAPER BW
PAPER BW
Black and white plain
paper upper thermistor
main set value
paper upper thermistor
main set value
190
200
F
HL_LM PLAIN
PAPER BW
PAPER BW
Black and white plain
paper lower thermistor
main set value
paper lower thermistor
main set value
150
155
G
HL_US PLAIN
PAPER BW
PAPER BW
Black and white plain
paper upper thermistor
sub set value
paper upper thermistor
sub set value
180
190
H
HL_EX PLAIN
PAPER BW
PAPER BW
Black and white plain
paper external
thermistor set value
paper external
thermistor set value
220
220
SIMULATION NO.41-03
TEST
PD SENSOR DISPLAY
OCSW
1
:
1/1
PD1[
]
:
PD2[
]
:
PD3[
]
:
PD4[
]
:
PD5[
]
:
PD6[
]
:
PD7[
]
:
CLOSE
I
HL_UM PLAIN
PAPER CL
PAPER CL
Color plain paper upper
thermistor main set
value
thermistor main set
value
200
200
J
HL_LM PLAIN
PAPER CL
PAPER CL
Color plain paper lower
thermistor main set
value
thermistor main set
value
140
140
K
HL_US PLAIN
PAPER CL
PAPER CL
Color plain paper upper
thermistor sub set value
thermistor sub set value
190
190
L
HL_EX PLAIN
PAPER CL
PAPER CL
Color plain paper
external thermistor set
value
external thermistor set
value
210
210
M
WARMUP
FUMON HL_EX
TEMP
FUMON HL_EX
TEMP
Fusing motor front
rotation start external
thermistor set value
rotation start external
thermistor set value
170
175
N
WARMUP
FUMOFF TIME
FUMOFF TIME
Fusing motor front
rotation continuation
time thermistor set value
rotation continuation
time thermistor set value
5
5
O
WARM UP END
TIME
TIME
Warm up completion
time
time
250
250
P
HL_UM HEAVY1
PAPER BW
PAPER BW
Black and white heavy
paper 1 upper thermistor
main set value
paper 1 upper thermistor
main set value
185
185
Q
HL_LM HEAVY1
PAPER BW
PAPER BW
Black and white heavy
paper 1 lower thermistor
main set value
paper 1 lower thermistor
main set value
130
130
R
HL_US HEAVY1
PAPER BW
PAPER BW
Black and white heavy
paper 1 upper thermistor
sub set value
paper 1 upper thermistor
sub set value
175
175
S
HL_EX HEAVY1
PAPER BW
PAPER BW
Black and white heavy
paper 1 external
thermistor set value
paper 1 external
thermistor set value
220
220
T
HL_UM HEAVY1
PAPER CL
PAPER CL
Color heavy paper 1
upper thermistor main
set value
upper thermistor main
set value
185
185
U
HL_LM HEAVY
1 PAPER CL
1 PAPER CL
Color heavy paper 1
lower thermistor main
set value
lower thermistor main
set value
130
130
V
HL_US HEAVY1
PAPER CL
PAPER CL
Color heavy paper 1
upper thermistor sub set
value
upper thermistor sub set
value
175
175
W
HL_EX HEAVY1
PAPER CL
PAPER CL
Color heavy paper 1
external thermistor set
value
external thermistor set
value
205
205
X
HL_UM HEAVY2
PAPER BW
PAPER BW
Black and white heavy
paper 2 upper thermistor
main set value
paper 2 upper thermistor
main set value
185
185
Y
HL_LM HEAVY2
PAPER BW
PAPER BW
Black and white heavy
paper 2 lower thermistor
main set value
paper 2 lower thermistor
main set value
140
140
Z
HL_US HEAVY2
PAPER BW
PAPER BW
Black and white heavy
paper 2 upper thermistor
sub set value
paper 2 upper thermistor
sub set value
185
185
AA
HL_EX HEAVY2
PAPER BW
PAPER BW
Black and white heavy
paper 2 external
thermistor set value
paper 2 external
thermistor set value
220
220
AB
HL_UM HEAVY2
PAPER CL
PAPER CL
Color heavy paper 2
upper thermistor main
set value
upper thermistor main
set value
185
185
AC
HL_LM HEAVY2
PAPER CL
PAPER CL
Color heavy paper 2
lower thermistor main
set value
lower thermistor main
set value
140
140
AD
HL_US HEAVY2
PAPER CL
PAPER CL
Color heavy paper 2
upper thermistor sub set
value
upper thermistor sub set
value
185
185
AE
HL_EX HEAVY2
PAPER CL
PAPER CL
Color heavy paper 2
external thermistor set
value
external thermistor set
value
210
210
AF
HL_UM OHP
PAPER
PAPER
OHP upper thermistor
main set value
main set value
180
180
AG
HL_LM OHP
PAPER
PAPER
OHP lower thermistor
main set value
main set value
130
130
AH
HL_US OHP
PAPER
PAPER
OHP upper thermistor
sub set value
sub set value
180
180
Item
Default value
62-sheet
machine
machine
70-sheet
machine
machine
Click on the first or last page to see other MX-6201N / MX-7001N (serv.man19) service manuals if exist.