Sharp MX-6201N / MX-7001N (serv.man19) Service Manual ▷ View online
MX-7001N SIMULATION 7 – 37
26-69
Purpose
Setting
Function (Purpose) Used to set the display of spare toner prep-
aration and near end when the toner quan-
tity reaches 25%.
tity reaches 25%.
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
*1: Enable when the set item B is set to "0." The numbers of
printable quantity on the table above are estimated with A4
paper and the print rate of 5%.
The toner near end message is displayed. When the printing
quantity set in item D is reached, it is judged as "Toner end."
During this operation, insufficient density, thin spot, or improper
color balance may occur depending on the user's status of use.
To avoid this symptom, set the set item D to "1."
paper and the print rate of 5%.
The toner near end message is displayed. When the printing
quantity set in item D is reached, it is judged as "Toner end."
During this operation, insufficient density, thin spot, or improper
color balance may occur depending on the user's status of use.
To avoid this symptom, set the set item D to "1."
*2: The output quantity in items D and E are based on A4 paper
with print ratio of 5%.
27
27-1
Purpose
Setting
Function (Purpose) Used to set non-detection of communica-
tion error (U7-00) with RIC
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: Non-detection
0: Non-detection
1: Detection
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
27-2
Purpose
Setting
Function (Purpose) Used to set the FSS function (sender regis-
tration number, host server telephone num-
ber).
ber).
Section
Operation/Procedure
1)
1)
Select an item to be set with touch panel.
[USER FAX NO] [SERVA TEL NO]
[USER FAX NO] [SERVA TEL NO]
2)
Enter the adjustment value with 10-key.
3)
Press [SET] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
A
TONER
PREPARATION
PREPARATION
0:
Toner ready message, icon display
(Default)
(Default)
1:
The toner preparation message is not
displayed.
displayed.
B
TONER NEAR
END
END
0:
Toner near end message display (Default)
1:
The toner near end message is not
displayed.
displayed.
C
TONER END
1:
Cartridge motor operation enabled at
NEAR END (Setting disable)
NEAR END (Setting disable)
2:
Cartridge motor operation disabled at
NEAR END (Setting disable)
NEAR END (Setting disable)
3:
Cartridge motor operation disabled at
NEAR END
NEAR END
D
TH COUNT (CL) *2
1:
Toner end detection in 0 sheet after toner
near end
near end
2:
Toner end detection in 25 sheets after
toner near end *1
toner near end *1
3:
Toner end detection in 50 sheet after toner
near end *1
near end *1
4:
Toner end detection in 100 sheets after
toner near end *1
toner near end *1
5:
Toner end detection in 200 sheets after
toner near end *1
toner near end *1
E
CONTINUOUS TH
COUNT (BK) *2
COUNT (BK) *2
1:
Cover open detection (recognition) in
120sec after toner cover open
120sec after toner cover open
2:
Cover open detection (recognition) in
210sec after toner cover open
210sec after toner cover open
3:
Cover open detection (recognition) in
300sec after toner cover open
300sec after toner cover open
4:
Cover open detection (recognition) in
390sec after toner cover open
390sec after toner cover open
5:
Cover open detection (recognition) in
480sec after toner cover open
480sec after toner cover open
A: 0
;
TONER PREPARATION(0:YES 1:NO)
B : 0
;
TONER NEAR END (0:YES 1:NO)
C : 3
;
NEAR END
A:
SIMULATION NO.26-69
TONER NEAR END SETTING
0
0
1
OK
TEST
CLOSE
D : 3
;
TH COUNTER(CL)
E : 3
;
CONTINUOUS TH COUNT(BK)
USER FAX_NO.
Sender registration number (Max. 16 digits)
SERVA TEL_NO.
Host server telephone number (Max. 16 digits)
A : 0
; DISABLE : YES
A:
SIMULATION NO.27-01
DISABLING OF U7-00 TROUBLE
0
0
1
OK
TEST
CLOSE
USER FAX_NO.
SERVA TEL_NO.
SIMULATION NO.27-02
TEST
FSS FUNCTION SETUP (INPUT)
1/1
0000000000000001
:
:
PRESENT
NEW
SET
CLOSE
PAUSE
MX-7001N SIMULATION 7 – 38
27-4
Purpose
Setting
Function (Purpose) Used to set the FSS function (initial, call,
toner order automatic send).
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
27-5
Purpose
Setting
Function (Purpose) Used to set the machine tag No. (This func-
tion allows the host computer to check the
machine tag No.)
machine tag No.)
Section
Communication (RIC/MODEM)
Operation/Procedure
1)
1)
Enter the set value (max. 8 digits) with 10-key. The set value is
displayed in NEW.
displayed in NEW.
2)
Press [SET] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
27-6
Purpose
Setting
Function (Purpose) Used to set the FSS function (manual ser-
vice call).
Section
Operation/Procedure
1)
1)
Enter the adjustment value with 10-key.
0: YES (Default)
0: YES (Default)
1: NO
2)
Press [OK] key.
The set value in step 1 is saved.
The set value in step 1 is saved.
27-7
Purpose
Setting
Function (Purpose) Used to set the FSS function (enable, alert
call).
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
*1: The FSS function setting can be changed only from Disable to
Enable. (Cannot be changed from Enable to Disable.)
*2: Alert send timing
A
FSS MODE
0:
Exclusive for send in the NE-B mode
1:
For send and receive in the NE-F
mode (Default)
mode (Default)
B
RETRY_BUSY
0 - 15 :
Resend number at busy state
(2: default)
(2: default)
C
RETRY (MINUTE)
_BUSY
_BUSY
1 - 15 :
Resend timer at busy state (min)
(3: default)
(3: default)
D
RETRY_ERROR
0 - 15 :
Resend number at error state
(1: default)
(1: default)
E
TIMER (MINUTE)
_ERROR
_ERROR
1 - 15 :
Resend timer at error state (min)
(1: default)
(1: default)
F
TONER ORDER
TIMING (K)
Toner order automatic
send timing (K)
TIMING (K)
Toner order automatic
send timing (K)
5:
100% - 75%
4:
74% - 50%
3:
49% - 25% (Default)
2:
25% or less
1:
Near end
0:
Empty
G
TONER ORDER
TIMING (C)
Toner order automatic
send timing (C)
TIMING (C)
Toner order automatic
send timing (C)
5:
100% - 75%
4:
74% - 50%
3:
49% - 25% (Default)
2:
25% or less
1:
Near end
0:
Empty
H
TONER ORDER
TIMING (M)
Toner order automatic
send timing (M)
TIMING (M)
Toner order automatic
send timing (M)
5:
100% - 75%
4:
74% - 50%
3:
49% - 25% (Default)
2:
25% or less
1:
Near end
0:
Empty
I
TONER ORDER
TIMING (Y)
Toner order automatic
send timing (Y)
TIMING (Y)
Toner order automatic
send timing (Y)
5:
100% - 75%
4:
74% - 50%
3:
49% - 25% (Default)
2:
25% or less
1:
Near end
0:
Empty
A㧦 1
㧧
FSS MODE㧦NEB2
B㧦 2
㧧
RETRY_BUSY
C㧦 3
㧧
TIMER㧔MINUTE㧕_BUSY
D㧦 1
㧧
RETRY_ERROR
A:
SIMULATION NO.27㧙04
FSS FUNCTION SETUP
1
㨇
0㨪 3 㨉
OK
TEST
CLOSE
E㧦 1
㧧
TIMER㧔MINUTE㧕_ERROR
F㧦 3
㧧
TONER ORDER TIMING(K)㧦3㧔49%㧙25%㧕
G㧦 3
㧧
TONER ORDER TIMING(C)㧦3㧔49%㧙25%㧕
H㧦 3
㧧
TONER ORDER TIMING(M)㧦3㧔49%㧙25%㧕
I㧦 3
㧧
TONER ORDER TIMING(Y)㧦3㧔49%㧙25%㧕
A
FUNCTION
0: FSS function enable
1: FSS function disable (*1) (Default)
1: FSS function disable (*1) (Default)
B
ALERT
0: Alert call enable (*2) (Default)
1: Alert call disable
1: Alert call disable
SIMULATION NO.27-05
TEST
TAG# SETTING
11111111
PRESENT :
NEW :
CLOSE
A : 0
;
0:YES, 1:NO
A:
SIMULATION NO.27-06
MANUAL SERVICE CALL SETUP
0
0
1
OK
TEST
CLOSE
MX-7001N SIMULATION 7 – 39
27-9
Purpose
Setting
Function (Purpose) Paper transport time between sensors /
Gain adjustment retry number setting
Section
Operation/Procedure
1)
1)
Select an item to be set with [
↑] and [↓] keys.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key.
The set value in step 2 is saved.
The set value in step 2 is saved.
27-10
Purpose
Data clear
Function (Purpose) Used to clear the history information of
trouble prediction
Section
Operation/Procedure
1)
1)
Press [EXECUTE] key.
2)
Press [YES] key.
The history information of trouble prediction is cleared.
The history information of trouble prediction is cleared.
27-11
Purpose
Other
Function (Purpose) Used to check the serial communication
retry number history and the scanner gain
adjustment retry number history.
adjustment retry number history.
Section
Operation/Procedure
The serial communication retry number history and the scanner
gain adjustment retry number history are displayed.
The serial communication retry number history and the scanner
gain adjustment retry number history are displayed.
No alert cause
Initial state / Trouble / Continuous JAM alert
Maintenance
When the maintenance timing is reached.
Service call
When pressing Service call.
Toner send request
When the toner order automatic send setting is
reached.
reached.
Toner collection
request
request
Revision of the toner installation date (only for a
new product)
new product)
A
FEED TIME 1
0 - 100:
Threshold value of the paper
transport time between sensors
(Main unit) (50: Default)
transport time between sensors
(Main unit) (50: Default)
B
FEED TIME 2
0 - 100:
Threshold value of the paper
transport time between sensors
(DSPF) (50: Default)
transport time between sensors
(DSPF) (50: Default)
C
GAIN ADJUSTMENT
RETRY
RETRY
1 - 100:
Threshold value of the gain
adjustment retry number (50:
Default)
adjustment retry number (50:
Default)
D
JAM ALERT
1 - 100:
Threshold value of the continuous
JAM alert judgment (10: Default)
JAM alert judgment (10: Default)
A : 1
;
FUNCTION(0:YES 1:NO)
B : 0
;
ALERT(0:YES 1:NO)
A:
SIMULATION NO.27-07
FSS FUNCTION SETUP (FUNCTION)
1
0
1
OK
TEST
CLOSE
A : 50
; FEED TIME1
B : 50
; FEED TIME2
C : 50
; GAIN ADJUSTMENT RETRY
D : 10
; JAM ALERT
A:
SIMULATION NO.27-09
FSS FUNCTION ADJUSTMENT
50
0
100
OK
TEST
CLOSE
Target history
Serial communication retry number history
High density process control error history
Medium density process control error history
Automatic registration adjustment error history
Gain adjustment retry history
Paper transport time between sensors
High density process control error history
Medium density process control error history
Automatic registration adjustment error history
Gain adjustment retry history
Paper transport time between sensors
Serial communication retry number
history display
history display
LSU1
LSU2
DESK1
DESK2
INSERTER1
INSERTER2
FINISHER1
FINISHER2
DSPF1
DSPF2
LSU2
DESK1
DESK2
INSERTER1
INSERTER2
FINISHER1
FINISHER2
DSPF1
DSPF2
Scanner gain adjustment retry history
display
display
SCAN GAIN ADJ1
SCAN GAIN ADJ2
SCAN GAIN ADJ3
SCAN GAIN ADJ4
SCAN GAIN ADJ5
SCAN GAIN ADJ2
SCAN GAIN ADJ3
SCAN GAIN ADJ4
SCAN GAIN ADJ5
DSPF gain adjustment retry history
display
display
DSPF GAIN ADJ1
DSPF GAIN ADJ2
DSPF GAIN ADJ3
DSPF GAIN ADJ4
DSPF GAIN ADJ5
DSPF GAIN ADJ2
DSPF GAIN ADJ3
DSPF GAIN ADJ4
DSPF GAIN ADJ5
SIMULATION NO.27-10
TEST
TROUBLE PRECOGNITION HISTORY CLEAR
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
MX-7001N SIMULATION 7 – 40
27-12
Purpose
Other
Function (Purpose) Used to check the error history of high den-
sity, half tone process control, and auto-
matic registration adjustment.
matic registration adjustment.
Section
Operation/Procedure
The high density error history, the half tone error history, and the
automatic registration adjustment error history are displayed.
The high density error history, the half tone error history, and the
automatic registration adjustment error history are displayed.
27-13
Purpose
Other
Function (Purpose) Used to check the history of paper transport
time between sensors.
Section
Operation/Procedure
Select the display with [
Select the display with [
↑] and [↓] keys.
<Cord between sensors>
HV_ERR1
High density error history 1
HV_ERR2
High density error history 2
HV_ERR3
High density error history 3
HV_ERR4
High density error history 4
HV_ERR5
High density error history 5
H_TONE ERR1
Half tone error history 1
H_TONE ERR2
Half tone error history 2
H_TONE ERR3
Half tone error history 3
H_TONE ERR4
Half tone error history 4
H_TONE ERR5
Half tone error history 5
AUTO REG ADJ1
Automatic registration adjustment error history 1
AUTO REG ADJ2
Automatic registration adjustment error history 2
AUTO REG ADJ3
Automatic registration adjustment error history 3
AUTO REG ADJ4
Automatic registration adjustment error history 4
AUTO REG ADJ5
Automatic registration adjustment error history 5
SIMULATION NO.27-11
TEST
TROUBLE PRECOGNITION RESULT
CLOSE
DATE
RETRY
LSU1
: 99/99/99 99:99:99
99999999
LSU2
: 99/99/99 99:99:99
99999999
DESK1
: 99/99/99 99:99:99
99999999
DESK2
: 99/99/99 99:99:99
99999999
INSERTER1
: 99/99/99 99:99:99
99999999
INSERTER2
: 99/99/99 99:99:99
99999999
FINISHER1
: 99/99/99 99:99:99
99999999
FINISHER2
: 99/99/99 99:99:99
99999999
DSPF1
: 99/99/99 99:99:99
99999999
DESK2
: 99/99/99 99:99:99
99999999
SCAN GAIN ADJ1 : 99/99/99 99:99:99
99999999
SCAN GAIN ADJ2 : 99/99/99 99:99:99
99999999
SCAN GAIN ADJ3 : 99/99/99 99:99:99
99999999
SCAN GAIN ADJ4 : 99/99/99 99:99:99
99999999
SCAN GAIN ADJ5 : 99/99/99 99:99:99
99999999
DSPF GAIN ADJ1 : 99/99/99 99:99:99
99999999
DSPF GAIN ADJ2 : 99/99/99 99:99:99
99999999
1/2
SIMULATION NO.27-12
TEST
TROUBLE PRECOGNITION RESULT(ADJUSTMENT_ERROR)
CLOSE
DATE
ERROR CODE
1/1
HV_ERR1
: 99/99/99 99:99:99
9999
HV_ERR2
: 99/99/99 99:99:99
9999
HV_ERR3
: 99/99/99 99:99:99
9999
HV_ERR4
: 99/99/99 99:99:99
9999
HV_ERR5
: 99/99/99 99:99:99
9999
H_TONE ERR1
: 99/99/99 99:99:99
9999
H_TONE ERR2
: 99/99/99 99:99:99
9999
H_TONE ERR3
: 99/99/99 99:99:99
9999
H_TONE ERR4
: 99/99/99 99:99:99
9999
H_TONE ERR5
: 99/99/99 99:99:99
9999
AUTO REG ADJ1 : 99/99/99 99:99:99
9999
AUTO REG ADJ2 : 99/99/99 99:99:99
9999
AUTO REG ADJ3 : 99/99/99 99:99:99
9999
AUTO REG ADJ4 : 99/99/99 99:99:99
9999
AUTO REG ADJ5 : 99/99/99 99:99:99
9999
FEED TIME1
History 1 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME2
History 2 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME3
History 3 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME4
History 4 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME5
History 5 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME6
History 6 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME7
History 7 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME8
History 8 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME9
History 9 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME10
History 10 of paper transport time between
sensors (ms)
sensors (ms)
FEED TIME1(DSPF)
History 1 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME2(DSPF)
History 2 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME3(DSPF)
History 3 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME4(DSPF)
History 4 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME5(DSPF)
History 5 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME6(DSPF)
History 6 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME7(DSPF)
History 7 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME8(DSPF)
History 8 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME9(DSPF)
History 9 of paper transport time between DSPF
sensors (ms)
sensors (ms)
FEED TIME10(DSPF)
History 10 of paper transport time between DSPF
sensors (ms)
sensors (ms)
Sensors A
Sensors B
Status
Cord between sensors
Bk
Color
Heavy
paper
PPD1
PPD2
On
→ On
0
40
80
Off
→ Off
1
41
81
PPD2
POD1
On
→ On
2
42
82
Off
→ Off
3
43
83
POD1
POD2
On
→ On
4
44
84
Off
→ Off
5
45
85
POM
reverse
rotation
reverse
rotation
POD3
On
→ On
6
46
86
APPD1
APPD2
On
→ On
0E
4E
8E
Off
→ Off
0F
4F
8F
APPD2
PPD1
On
→ On
10
50
90
Off
→ Off
11
51
91
CPUC1
CPFD1
On
→ On
12
52
92
CPFD1
PPD1
On
→ On
14
54
94
Off
→ Off
15
55
95
CPUC2
CPFD2
On
→ On
16
56
96
CPFD2
CPFD1
On
→ On
18
58
98
Off
→ Off
19
59
99
MPUC
PPD1
On
→ On
1A
5A
9A
Click on the first or last page to see other MX-6201N / MX-7001N (serv.man19) service manuals if exist.