Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man6) Service Manual ▷ View online
MX-6070N SIMULATION 6 – 6
44
22
Used to display the toner patch density
level in the halftone process control
operation
level in the halftone process control
operation
24
Used to display the correction target and
the correction level in the halftone process
control operation
the correction level in the halftone process
control operation
25
Used to set the calculating conditions of the
correction value for the halftone process
control
correction value for the halftone process
control
26
Used to execute the halftone process
control compulsory
control compulsory
1-5
2-3
27
Used to clear the correction data of the
halftone process control
halftone process control
28
Used to set the process control execution
conditions
conditions
29
Used to set the operating conditions of the
process control during a job
process control during a job
31
Used to adjust the OPC drum phase
(Manual adjustment)
(Manual adjustment)
37
Used to set the development bias
correction level in the continuous printing
operation
correction level in the continuous printing
operation
43
Used to display the identification
information of the developing unit
information of the developing unit
62
Used to set the process control execution
conditions
conditions
46
1
Used to adjust the copy density in the copy
mode
mode
2
Used to adjust the copy density in the copy
mode
mode
4
Used to adjust the density in the image
send mode
send mode
5
Used to adjust the density in the image
send mode
send mode
8
Used to adjust the image send mode color
balance RGB
balance RGB
9
Used to adjust the scan image density
3
10
Used to adjust the copy color balance and
the gamma (for each color copy mode)
the gamma (for each color copy mode)
16
Used to adjust the monochrome copy
density and the gamma
density and the gamma
19
Used to set the operating conditions for the
density scanning (exposure) of
monochrome auto copy mode documents
density scanning (exposure) of
monochrome auto copy mode documents
21
Copy color balance adjustment (manual
adjustment)
adjustment)
1-3
5
23
Used to set the density correction of copy
high density section (high density tone gap
supported)
high density section (high density tone gap
supported)
24
Copy color balance adjustment (auto
adjustment)
adjustment)
5
25
Used to adjust the copy color balance
(single color copy mode)
(single color copy mode)
26
Used to reset the single color mode color
balance set value to the default
balance set value to the default
27
Used to adjust the gamma/density of copy
images, text and line image edges
images, text and line image edges
30
Used to adjust the resolution in the sub
scanning direction in the copy mode
scanning direction in the copy mode
32
Used to adjust the document background
density reproducibility in the monochrome
auto copy mode
density reproducibility in the monochrome
auto copy mode
36
Used to adjust the colors in the two color
copy mode
copy mode
37
Used to adjust the reproduction capability of
monochrome mode color
monochrome mode color
38
Used to adjust the black component
amount in the color copy mode
amount in the color copy mode
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
46
39
Used to adjust the sharpness of FAX send
images
images
40
Used to adjust the FAX send image density
(Collective adjustment of all the modes)
(Collective adjustment of all the modes)
41
Used to adjust the FAX send image density
(Normal)
(Normal)
42
Used to adjust the FAX send image density
(Fine)
(Fine)
43
Used to adjust the FAX send image density
(Super fine)
(Super fine)
44
Used to adjust the FAX send image density
(Ultra fine)
(Ultra fine)
45
Used to adjust the FAX send image density
(600dpi)
(600dpi)
46
Used to adjust the FAX send image density
(RGB RIP)
(RGB RIP)
47
Used to set the compression rate of copy
and scan images (JPEG)
and scan images (JPEG)
48
Used to set the copy output resolution of
copy mode
copy mode
51
Used to adjust the gamma for the copy
mode heavy paper mode and the image
process mode
mode heavy paper mode and the image
process mode
52
Used to set the gamma default for the copy
mode heavy paper and the image process
mode
mode heavy paper and the image process
mode
1-3
54
Used to perform the engine halftone
automatic density adjustment (dither)
automatic density adjustment (dither)
1-3
55
Used to adjust the drop out color in the
image send mode (monochrome manual
text mode)
image send mode (monochrome manual
text mode)
58
Used to set the copy mode pseudo
resolution (smoothing process)
resolution (smoothing process)
60
Used to adjust the sharpness in the copy/
scan mode
scan mode
61
Used to adjust the area separation
recognition level
recognition level
62
Used to set the operating condition of the
ACS the area separation the background
image process and the auto exposure
mode
ACS the area separation the background
image process and the auto exposure
mode
63
Used to adjust the density in the copy low
density section
density section
65
Used to set the color correction table
66
Used to adjust the reproduction capability of
watermarks in the copy/printer mode
watermarks in the copy/printer mode
68
Used to adjust the auto resolution
judgement (For MX-xx70 series)
judgement (For MX-xx70 series)
74
Copy color balance adjustment (Auto
adjustment)/printer color balance
adjustment (Auto adjustment)
adjustment)/printer color balance
adjustment (Auto adjustment)
1-1
-5
2-2
-3
1-2
-3
90
Used to set the process operation of high
compression PDF images
compression PDF images
91
Used to adjust the reproduction capability of
black text
black text
48
1
Used to adjust the scan image
magnification ratio (in the main scanning
direction and the sub scanning direction)
magnification ratio (in the main scanning
direction and the sub scanning direction)
1-1
5
Used to correct the scan image
magnification ratio (in the sub scanning
direction)
magnification ratio (in the sub scanning
direction)
1-1
6
Used to adjust the rotation speed of each
motor
motor
49
1
Used to perform the firmware update
4
5
3
Used to update the operation manual
4
5
5
Used to perform the watermarks update
4
5
6
Used to perform the OCR update
10
Used to perform the ACU update
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
MX-6070N SIMULATION 6 – 7
50
1
Copy image position, image loss
adjustment
adjustment
1-1
5
Used to adjust the print lead edge image
position
position
1-1
6
Used to adjust the copy image position and
the image loss (SPF mode)
the image loss (SPF mode)
1-1
10
Used to adjust print image position
1-2
2-1
1-1
12
Used to perform the scan image off center
position adjustment
position adjustment
1-1
20
Image registration adjustment (Main
scanning direction)
scanning direction)
1-2
22
Used to adjust the image registration (Main
scan direction, sub scan direction)
scan direction, sub scan direction)
1-1
2-1
1-1
-2
23
Used to set the registration for temperature
adjustment
adjustment
24
Used to display the detail data of SIM 44-2,
50-22
50-22
27
Used to perform the image loss adjustment
of scanned images in the FAX or image
send mode
of scanned images in the FAX or image
send mode
28
Used to automatically adjust the image
loss, void area, image off center and image
magnification ratio
loss, void area, image off center and image
magnification ratio
51
1
Used to adjust the ON/OFF timing of the
secondary transport voltage
secondary transport voltage
2
Used to adjust the contact pressure
(deflection amount) on paper by the main
unit and the SPF resist roller
(deflection amount) on paper by the main
unit and the SPF resist roller
53
6
Used to adjust the detection level of the
SPF document width
SPF document width
3
7
Used to adjust the SPF document size
width sensor
width sensor
8
Used to adjust the document lead edge
reference and the SPF mode document
scan position
reference and the SPF mode document
scan position
3
9
SPF dirt detection setting
10
SPF dirt detection execution
55
1
Used to set the specification of the engine
control operations (SOFT SW)
control operations (SOFT SW)
2
Used to set the specifications of the
scanner control operation (SOFT SW)
scanner control operation (SOFT SW)
3
Used to set the specifications of the
controller operation (SOFT SW)
controller operation (SOFT SW)
10
Used to set the special stamp text for
Taiwan
Taiwan
56
1
Used to transport data between HDD - MFP
PWB SRAM/EEPROM
PWB SRAM/EEPROM
2
Used to backup the data in the EEPROM
and HDD to the USB memory
and HDD to the USB memory
3
Used to backup the document filing data to
the USB memory
the USB memory
4
Used to backup the JOB log data to the
USB memory
USB memory
5
Used to import the SIM22-6 data to a USB
memory in the text format
memory in the text format
6
Used to output the JAM/trouble data
7
Used to export system log data to the USB
memory
memory
8
Used to perform ICC profile update
15
MFP EEPROM data restore
99
Used to export system log data to the USB
memory
memory
3-4
1-5
9-4
60
1
Used to check the memory operations
(read/write) of the SCU-MFP PWB
(read/write) of the SCU-MFP PWB
61
1
Used to check the LSU polygon motor
rotation and laser detection
rotation and laser detection
3
Used to set the laser power
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
61
4
Used to print the print image skew
adjustment pattern
adjustment pattern
11
Used to correct the laser power
automatically
automatically
2-3
1-2
-3
12
Laser power manual correction
13
Used to clear the laser power correction
value
value
2-3
1-3
14
Used to set the laser power correction
1-3
62
1
Used to format the HDD
2
Used to check read/write of the HDD
(partial)
(partial)
3
Used to check read/write of the HDD (all
areas)
areas)
6
Used to perform the self diagnostics of the
HDD
HDD
7
Used to print the HDD self diagnostics error
log
log
8
Used to format the HDD
10
Used to clear the job completion list data
11
Used to delete the document filing data
12
Used to set Enable/Disable of auto format
in a HDD trouble
in a HDD trouble
13
Used to format the HDD (Operation manual
watermark data only)
watermark data only)
14
Used to delete the document filing
management data
management data
20
Used to check the status display of HDD
63
1
Used to display the shading correction
result
result
2
Used to perform shading
1-5
3
3
Used to perform scanner (CCD) color
balance and gamma auto adjustment
balance and gamma auto adjustment
1-5
2-3
3
4
Used to display the scanner test chart patch
density
density
5
Used to perform the scanner (CCD) color
balance and gamma default setting
balance and gamma default setting
2-3
3
7
Used to register the service target of the
copy mode auto color balance adjustment
copy mode auto color balance adjustment
5
8
Used to set the default of the service target
of the copy mode auto color balance
adjustment
of the copy mode auto color balance
adjustment
5
11
Used to set the target color balance of the
copy mode auto color balance adjustment
copy mode auto color balance adjustment
5
64
1
Test print (self print) (color mode)
2
Test print (self print) (monochrome mode)
8
4
Printer test print (self print)
5
Printer test print (self print) (PCL)
1-4
6
Printer test print (self print) (PS)
65
1
Used to adjust the touch panel (LCD display
section) detection coodinates
section) detection coodinates
7
2
Used to display the touch panel (LCD
display section) detection coodinates
display section) detection coodinates
5
Used to check the operation panel key input
66
1
Used to display the image send-related soft
SW (2-150) on the LCD to allow changing
the soft SW while checking with the LCD
SW (2-150) on the LCD to allow changing
the soft SW while checking with the LCD
2-3
2
Used to enter a country code and set the
default value for the country code
default value for the country code
3
Used to check read/write of the EEPROM
and the SDRAM on the MODEM controller
and display the result
and the SDRAM on the MODEM controller
and display the result
4
Used to send the selected signals to the
line and the main unit speaker (send level:
max)
line and the main unit speaker (send level:
max)
5
Used to send the selected signal to the line
and the main unit speaker (send level: soft
SW setting)
and the main unit speaker (send level: soft
SW setting)
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
1
: ‘16/Sep.
1
1
MX-6070N SIMULATION 6 – 8
66
6
Used to print the confidential registration
check table (BOX No, BOX name,
passcode
check table (BOX No, BOX name,
passcode
7
Used to output all image data saved in the
image memory
image memory
8
Used to send the selected sound message
to the line and the speaker (send level:
max)
to the line and the speaker (send level:
max)
9
Used to send the selected sound message
to the line and the speaker (send level: soft
SW setting)
to the line and the speaker (send level: soft
SW setting)
10
Used to clear the FAX and image send
image data
image data
11
Used to send the selected signal at 300bps
to the line and the speaker (send level:
max)
to the line and the speaker (send level:
max)
12
Used to send the selected signal at 300bps
to the line and the speaker (send level: soft
SW setting)
to the line and the speaker (send level: soft
SW setting)
13
Used to register dial number for Sim66-14/
15/16 dial test
15/16 dial test
14
Used to execute the dial pulse (10pps) send
test and to adjust the make time
test and to adjust the make time
15
Used to execute the dial pulse (20pps) send
test and to adjust the make time
test and to adjust the make time
16
Used to execute the DTMF signal send test
and to adjust the send level
and to adjust the send level
17
Used to send the DTMF signal to the line
and the speaker (send level: max)
and the speaker (send level: max)
18
Used to send the DTMF signal to the line
and the speaker (send level: soft SW
setting)
and the speaker (send level: soft SW
setting)
21
Used to print the selected items (system
error, protocol monitor)
error, protocol monitor)
22
Used to set the handset sound volume
(Japan model only)
(Japan model only)
29
Used to initialize the telephone book data
and FAX system error
and FAX system error
30
Used to display the TEL/LIU status change,
the display is highlighted by status change
the display is highlighted by status change
31
Used to set ON/OFF the port for output to
TEL/LIU
TEL/LIU
32
Used to check the fixed data received from
the line and to display the result
the line and to display the result
33
Used to execute detection of various
signals with the line connected and to
display the detection result. When a signal
is detected the display is highlighted
signals with the line connected and to
display the detection result. When a signal
is detected the display is highlighted
36
Used to check send and receive data from
the MODEM controller to the MFP controller
or the data line or the command line
individually
the MODEM controller to the MFP controller
or the data line or the command line
individually
39
Used to check and change the destination
setting saved in EEPROM of the FAX BOX
setting saved in EEPROM of the FAX BOX
42
Used to rewrite the program to power
control installed in the FAX BOX
control installed in the FAX BOX
43
Used to write the adjustment value into the
power control installed in the FAX BOX
power control installed in the FAX BOX
61
Used to display the image send-related soft
SW (151-250) on the LCD to allow
changing the soft SW while checking with
the LCD
SW (151-250) on the LCD to allow
changing the soft SW while checking with
the LCD
62
Used to import the FAX receive data into a
USB memory in PDF file type
USB memory in PDF file type
67
17
Printer reset
24
Printer color balance adjustment (Auto
adjustment)
adjustment)
6
25
Printer color balance adjustment (Manual
adjustment)
adjustment)
1-4
6
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
67
26
Used to set the target color balance of the
printer mode auto color balance adjustment
printer mode auto color balance adjustment
6
27
Used to set the service target of the printer
mode auto color balance adjustment
mode auto color balance adjustment
6
28
Used to set the default of the service target
of the printer mode auto color adjustment
of the printer mode auto color adjustment
6
31
Used to clear the printer calibration value
33
Used to change the gamma of the printer
screen
screen
34
Used to set the density correction in the
printer high density section
printer high density section
36
Used to adjust the density in the low density
section
section
41
Used to set 2 color print
42
Used to set 2 color print color density
43
Used to adjust 2 color mode color balance
52
Used to set the default of the gamma of the
printer screen
printer screen
1-3
54
Printer color balance adjustment
1-3
Sim No.
Easy Mode
In
st
a
lla
ti
o
n
Main
te
nance
Adjus
tm
e
nt and
Set
ti
ngs
MX-6070N SIMULATION 6 – 9
5. Details of simulation
1
1-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
scan resolution (operation speed).
1-2
Purpose
Operation test/check
Function (Purpose)
Used to check the sensors in the scanner
(reading) section and the related circuits.
(reading) section and the related circuits.
Section
Scanner (reading)
Operation/Procedure
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
1-5
Purpose
Operation test/check
Function (Purpose)
Used to check the operation of the scanner
(reading) unit and the control circuit.
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
1) Select the operation speed with the touch panel key.
2) Press [EXECUTE] key.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
2
2-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the auto-
matic document feeder and the control cir-
cuit.
matic document feeder and the control cir-
cuit.
Section
SPF
Operation/Procedure
1) Select the operation mode and the speed with the touch panel
1) Select the operation mode and the speed with the touch panel
key.
2)
Press [EXECUTE] key.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
RSPF
DSPF
2-2
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the sen-
sors and the detectors in the automatic
document feeder section and the control
circuits.
sors and the detectors in the automatic
document feeder section and the control
circuits.
Section
Automatic document feeder
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
RSPF
DSPF
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI (372mm/s)
400DPI
400DPI (372mm/s)
600DPI
600DPI (264.0mm/s)
1200DPI
1200DPI (132mm/s)
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI (372mm/s)
300DPI (372mm/
s)
s)
400DPI
400DPI (372mm/s)
600DPI
600DPI (264.0mm/s)
1200DPI
1200DPI (132mm/s)
Item/Display
Operation mode
Default value
SPF SCAN
(SINGLE)
(SINGLE)
300DPI
300DPI(396.0mm/s)
300DPI
(396.0mm/s)
(396.0mm/s)
400DPI
400DPI(396.0mm/s)
600DPI
600DPI(264.0mm/s)
SPF SCAN
(DOUBLE)
(DOUBLE)
300DPI
300DPI(396.0mm/s)
300DPI
(396.0mm/s)
(396.0mm/s)
400DPI
400DPI(396.0mm/s)
600DPI
600DPI(264.0mm/s)
Item/Display
Operation mode
Default value
SPF SCAN
(SINGLE)
(SINGLE)
300DPI
300DPI(496.0mm/s)
300DPI
(496.0mm/s)
(496.0mm/s)
400DPI
400DPI(396.0mm/s)
600DPI
600DPI(264.0mm/s)
SPF SCAN
(DOUBLE)
(DOUBLE)
300DPI
300DPI(496.0mm/s)
300DPI
(496.0mm/s)
(496.0mm/s)
400DPI
400DPI(396.0mm/s)
600DPI
600DPI(264.0mm/s)
Display
Content
SPED
Document sensor
SPPD1
Document transport sensor 1
SPLS1
Paper size detector 1
SPLS2
Paper size detector 2
SOCD
SPF open/close sensor
SPPD2
Document transport sensor 2
SPPD3
Document transport sensor 3
SPPD4
Document transport sensor 4
SCOV
SPF cover open/close detector
SSET
SPF installation detection
STMPU
SPF stamp UN installation detection
SWD_LEN
SPF document guide plate position (Unit: 0.1mm)
SWD_AD
SPF document detection volume output AD value
Display
Content
SCOV
SPF cover open/close detector
SLCOV
Lower door open/close sensor
SOCD
SPF open/close sensor
SPED1
Document empty sensor
SPED2
Document empty sensor
SPLS1
Paper size detector 1
SPLS2
Paper size detector 2
SPOD
Document exit sensor
SPPD1
Document transport sensor 1
SPPD2
Document transport sensor 2
SPPD3
Document transport sensor 3
SPPD4
Document transport sensor 4
SPPD5
Document transport sensor 5
SPRDMD
Document random sensor
STLD
Document feed tray lower limit sensor
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man6) service manuals if exist.