Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man3) Handy Guide ▷ View online
9
Document Solutions After Sales Service
Machine Consumables
Product Code
Description / Contents
Life (Approx.)
MX‐310X1
Primary Transfer Roller Kit:‐
•
Transfer roller x 4
•
Belt drive gear
MX‐310B2
Secondary Transfer Belt Kit:‐
•
Transfer belt only
MX‐410X2
Secondary Transfer Roller Kit:‐
•
Transfer roller
•
Drive idle gear
•
Upper Thermistor PA
Peripherals
MX‐SCX1
Finisher Staple (MXFNX9/MXFN10) Cartridge
5000 staples (x3)
AR‐SC3
Staple Cartridge for (MXFN10) Saddle Finisher
2000 staples (x 3)
AR‐SC2
Finisher (MXFN11) Staple Cartridge
5000 staples (x 3)
AR‐SV1
Ink Cartridge for Stamp Unit (AR‐SU1)
2 Units
AR‐620RT
Paper Feed Roller Kit
• Paper Feed Roller
• Paper Feed Pick Up Roller
• Paper Separation Roller
• Paper Feed Pick Up Roller
• Paper Separation Roller
100K
AR‐620DF
DSPF Roller Kit
• DSPF Paper Feed Roller
• DSPF Pick Up Roller
• DSPF Separation Roller
• DSPF Pick Up Roller
• DSPF Separation Roller
100K
Service Rotation Unit
MX‐410U1
Primary Transfer Belt Unit
For Service Rotation
MX‐410U2
Secondary Transfer Belt Unit
MX‐410FU
Fusing Unit (230v)
Note: The consumable life may vary, depending on document density, temperature, humidity and machine
operation.
10
Document Solutions After Sales Service
Initial Set‐Up
DEVELOPER INSTALLATION
Sim 25‐02
Auto Developer Adjustment
Select CMYK
Note: Toner Installation should be performed after
Auto Developer Adjustment is completed
For Optimum Image Quality it is recommended to
install developer at the customer site
Auto Developer Adjustment is completed
For Optimum Image Quality it is recommended to
install developer at the customer site
INITIAL SETTINGS
Sim 26‐06
Machine Destination Set
Sim 26‐02
LCC Paper Size setting
Sim 26‐52
Blank Paper Count Mode Setting (Non Print)
Sim 26‐65
Finisher Alarm mode
Select Staple sheet limit (30 or 50)
Staple copies/sets limit (ON/OFF)
Sim 26‐01
Right Tray Installation
Yes/No.
Sim 26‐35
Set Multi Error Counter
Set to 1 (Multi Count).
Sim 26‐78
Remote Desktop Access Password set.
CASSETTE SETUP & PAPER TYPE
Set cassette size by adjusting the guides in the cassette.
Paper Size & Type Setting:‐ System Settings – Paper Tray Settings
IMAGE WRITING DISTORTION – CMYK
Sim 61‐04
Image Writing Adjustment (Black)
Select Paper A3
SIM 50‐22
Image Writing Adjustment (Colour)
DRUM POSITION (PHASE) & COLOUR REGISTRATION
Sim 50‐22
Drum Pos Adjustment
Registration Adjustment
Select ALL
Note: Manual Colour Registration (Sim 50‐20/21) &
Drum Position (Sim 44‐31) adjustments can also be
performed if required.
Drum Position (Sim 44‐31) adjustments can also be
performed if required.
11
Document Solutions After Sales Service
Initial Set‐Up
PRINT IMAGE MAGNIFICATION & OFF CENTRE
Manual Adjustment:
Sim 50‐10
Adjust BK MAG to 240mm
Image Off Centre Adjustment
(All cassettes & ADU).
Automatic Adjustment:
Sim 50‐28
BK MAG ADJUST (Magnification)
SETUP/PRINT ADJ (Offset)
COPY IMAGE POSITION & VOID
Manual Adjustment:
Sim 50‐01
Lead/Rear Edge, Image Loss &
Void Adjustment
.
Sim 48‐01
Magnification Adjustment (OC)
Sim 50‐12
OC & SPF Off Centre Adjust.
Automatic Adjustment:
Sim 50‐28
OC ADJUST (Platen)
SPF ADJUST
RSPF & DSPF IMAGE POSITION & VOID
Manual Adjustment:
Sim 50‐06
SPF Lead Edge Adjust
Sim 50‐12
OC & SPF Off Centre Adjust.
Automatic Adjustment:
Sim 50‐28
OC ADJUST (Platen)
SPF ADJUST
HALF‐TONE ‐ COLOUR CALIBRATION
Copy/Engine:
Sim 46‐74
Automatic Colour Calibration
Please refer to Page 12 for Calibration Procedure.
Note: This Must Be Completed In Full
12
Document Solutions After Sales Service
Initial Set‐Up
IMAGE DENSITY
Sim 46‐01
Copy Density Adjust (Colour)
Sim 46‐02
Copy Density Adjust (B/W)
Sim 46‐04
Scanner Density Adjust (Colour)
Sim 46‐05
Scanner Density Adjust (Mono)
Sim 46‐09
DSPF Copy Density Adjust
PERIPHERALS
Sim 03‐10
Saddle/Staple Position Adjust (MX‐FN10 only)
FAX OPTION (MX‐FXX2)
Sim 66‐02
Fax SW Setting (Destination)
Sim 66‐39
Fax Destination Set
Sim 66‐10
Fax Memory Clear (For Standard Extended Memory)
MFP Status Display
Sim 55‐03
Toner Remaining Status Display SSW
22, Data/Bit 5 (Change from 0:1)
Product Activation & Firmware
Activation of Optional Products:
System Settings – Administrator Mode – Product Key
Sim 22‐05
Check Firmware version – Upgrade to latest version.
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man3) service manuals if exist.