Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man13) Service Manual ▷ View online
MX-4101N ADJUSTMENTS 5 – 77
2)
Select the item A, B with the scroll key.
* If a tone gap occurs on part of high density, set 0 to item A and B
The density of high density part decreases. However, the tone
gap is better.
gap is better.
* In case of more increase of the density on high density part, set 1
to item A and B.
The tone gap may occur in high density part.
The tone gap may occur in high density part.
NOTE: Do not change the setting values of item C, D, E and F. If
these values is changed, density of the high density part is
changed.
changed.
If these values is changed, be sure to execute the copy color bal-
ance density adjustment. (Auto adjustment)
ance density adjustment. (Auto adjustment)
20-P
Copy color balance adjustment (Single
color copy mode) (Normally not required)
color copy mode) (Normally not required)
This adjustment is used to set the color balance and the density in
the single color copy mode to the user's request.
The adjustment is made by changing Y, M, C components of each
color.
This adjustment is not required normally, but executed when there
is a request from the user.
When the default adjustment value is changed, this adjustment is
required in the following cases.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
the single color copy mode to the user's request.
The adjustment is made by changing Y, M, C components of each
color.
This adjustment is not required normally, but executed when there
is a request from the user.
When the default adjustment value is changed, this adjustment is
required in the following cases.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
a. Adjustment procedure
1)
1)
Enter the SIM 46-25 mode.
2)
Select the color to be adjusted with the scroll key.
3)
Select the color (YMC) to be adjusted with the color key.
4)
Enter the adjustment value with 10-key.
5)
Press [OK] key.
6)
Press [Close] key to exit the simulation.
7)
Make a copy in the single color copy mode and check the
copy.
copy.
If a satisfactory result is not obtained, return to the SIM 46-25 mode
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
20-Q
Copy density adjustment in the RSPF mode
(Normally unnecessary to adjust)
(Normally unnecessary to adjust)
This setting normally not required. When, however, there are case
of following, change the setting.
* When copy in RSPF mode differs from copy in document table
of following, change the setting.
* When copy in RSPF mode differs from copy in document table
mode.
* When copy density in RSPF mode is low or too high.
* When the RSPF unit is replaced.
* When the RSPF unit is disassembled.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
* When the RSPF unit is replaced.
* When the RSPF unit is disassembled.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
Display/Item
Content
Setting
range
Default
A
CMY
(0:ENABLE
1:DISABLE)
0
CMY engine
maximum density
correction mode
Enable
maximum density
correction mode
Enable
0 - 1
0
1
CMY engine
maximum density
correction mode
Disable
maximum density
correction mode
Disable
B
K
(0: ENABLE
1: DISABLE)
0
K engine maximum
density correction
mode Enable
density correction
mode Enable
0 - 1
1
1
K engine maximum
density correction
mode DIsable
density correction
mode DIsable
C
CYAN MAX
TARGET
Scanner target value for
CYAN maximum density
correction
CYAN maximum density
correction
0 - 999
500
D
MAGENTA MAX
TARGET
Scanner target value for
MAGENTA maximum
density correction
MAGENTA maximum
density correction
0 - 999
500
E
YELLOW MAX
TARGET
Scanner target value for
YELLOW maximum
density correction
YELLOW maximum
density correction
0 - 999
500
F
BLACK MAX
TARGET
Scanner target value for
BLACK maximum density
correction
BLACK maximum density
correction
0 - 999
500
Display/Item
Adjustment
range
Default
C
M
Y
A
RED
0 - 255
0
255
200
B
GREEN
0 - 255
255
0
255
C
BLUE
0 - 255
255
200
0
D
YELLOW
0 - 255
0
0
255
E
MAGENTA
0 - 255
0
255
0
F
CYAN
0 - 255
255
0
0
OK
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,1*/(&2/2502'(&2/25%$/$1&(6(783
$˖
˷̚˹
˖5('
$˖
˖*5((1
%˖
˖%/8(
&˖
˖&<$1
'˖
˖<(//2:
)˖
˖0$*(17$
(˖
2.
&
0
<
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,1*/(&2/2502'(&2/25%$/$1&(6(783
$˖
˷̚˹
˖5('
$˖
˖*5((1
%˖
˖%/8(
&˖
˖&<$1
'˖
˖<(//2:
)˖
˖0$*(17$
(˖
2.
&
0
<
MX-4101N ADJUSTMENTS 5 – 78
a. Adjustment procedure
1)
1)
Enter the SIM 46-9 mode.
2)
Select the mode to be adjusted with the scroll key.
When adjusting density on low density part, select "A (COPY
LOW)". When adjusting density on high density part, select "D
(COPY HIGH)".
When adjusting density on low density part, select "A (COPY
LOW)". When adjusting density on high density part, select "D
(COPY HIGH)".
3)
Enter the adjustment value with 10-key.
In case of increase of image density, input large numeric
value. Or in case of diluting the image density, input small
numeric value.
In case of increase of image density, input large numeric
value. Or in case of diluting the image density, input small
numeric value.
4)
Press [OK] key.
5)
Press [Close] key to exit the simulation.
6)
Make a copy in the single color copy mode and check the
copy.
copy.
If a satisfactory result is not obtained, return to the SIM 46-25 mode
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
20-R
DSPF mode copy density adjustment
(Normally not necessary to adjust)
(Normally not necessary to adjust)
It is normally not necessary to perform this adjustment.
In the following cases, however, this adjustment must be per-
formed.
* When the copy density differs in the DSPF mode and in the doc-
In the following cases, however, this adjustment must be per-
formed.
* When the copy density differs in the DSPF mode and in the doc-
ument table mode.
* When the copy density differs on the front surface and on the
back surface in the DSPF mode.
* When the copy density in the DSPF mode is too low or too high.
* When the DSPF unit is replaced.
* When the DSPF unit is disassembled.
* When the DSPF CCD unit is replaced.
* When U2 trouble occurs.
* When the DSPF unit is replaced.
* When the DSPF unit is disassembled.
* When the DSPF CCD unit is replaced.
* When U2 trouble occurs.
a. Adjustment procedures
(Front surface copy density adjustment)
1)
1)
Enter the SIM46-9 mode.
Item/Display
Content
Setting
range
De-
fault
A
COPY : LOW
RSPF copy mode exposure
adjustment (Low density side)
adjustment (Low density side)
1 - 99
48
B
SCAN : LOW
RSPF scanner mode exposre
adjustment (Low density side)
adjustment (Low density side)
1 - 99
48
C
FAX : LOW
PSPF FAX mode exposure
adjustment (Low density side)
adjustment (Low density side)
1 - 99
48
D
COPY : HIGH
RSPF copy copy mcde
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
53
E
SCAN : HIGH
RSPF scanner mode exposre
adjustment (Low density side)
adjustment (Low density side)
1 - 99
53
F
FAX : HIGH
RSPF FAX mode exposure
adjustment
(High density side)
adjustment
(High density side)
1 - 99
53
OK
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<˖/2:
$˖
˖6&$1˖/2:
%˖
˖)$;˖/2:
C
˖
˖&23<˖+,*+
D
˖
˖)$;˖+,*+
F
˖
˖6&$1˖+,*+
(˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<˖/2:
$˖
˖6&$1˖/2:
%˖
˖)$;˖/2:
C
˖
˖&23<˖+,*+
D
˖
˖)$;˖+,*+
F
˖
˖6&$1˖+,*+
(˖
2.
OK
DSPF
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<6,'($˖/2:
$˖
˖6&$16,'($˖/2:
%˖
˖)$;6,'($˖/2:
&˖
˖&23<6,'($˖+,*+
' 䋺
˖)$;6,'($˖+,*+
)˖
˖6&$16,'($˖+,*+
(˖
2.
'63)
2&
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<6,'(%˖/2:
$˖
˖6&$16,'(%˖/2:
%˖
˖)$;6,'(%˖/2:
&˖
˖&23<6,'(%˖+,*+
' 䋺
˖)$;6,'(%˖+,*+
)˖
˖6&$16,'(%˖+,*+
(˖
2.
'63)
2&
10-key
MX-4101N ADJUSTMENTS 5 – 79
2)
Press OC key to select the front surface copy density adjust-
ment mode.
ment mode.
3)
Select an adjustment mode with the scroll key.
To adjust the density in the low density area, select "COPY
SIDE A LOW." To adjust the density in the high density area,
select "COPY SIDE A HIGH."
To adjust the density in the low density area, select "COPY
SIDE A LOW." To adjust the density in the high density area,
select "COPY SIDE A HIGH."
4)
Enter an adjustment value with 10-key.
To increase the density, enter a greater number. To decrease
the density, enter a smaller number.
To increase the density, enter a greater number. To decrease
the density, enter a smaller number.
5)
Press [OK] key.
6)
Press [CLOSE] key to exit the simulation mode.
7)
Make a copy and check the copy density.
Repeat the above procedures until a satisfactory result is obtained.
(Back surface copy density adjustment)
1)
Enter the SIM46-9 mode.
Item
Button
Display
Content
Setting
range
Default
value
A
OC
COPY SIDEA:
LOW
LOW
DSPF copy mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
47
B
SCAN SIDEA:
LOW
LOW
DSPF scanner
mode exposure
adjustment (Low
density side)
mode exposure
adjustment (Low
density side)
1 - 99
47
C
FAX SIDEA:
LOW
LOW
DSPF FAX mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
47
D
COPY SIDEA:
HIGH
HIGH
DSPF copy mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
52
E
SCAN SIDEA:
HIGH
HIGH
DSPF scanner
mode exposre
adjustment (High
density side)
mode exposre
adjustment (High
density side)
1 - 99
52
F
FAX SIDEA:
HIGH
HIGH
DSPF FAX mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
52
A
DSPF
COPY SIDEB:
LOW
LOW
DSPF copy mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
47
B
SCAN SIDEB:
LOW
LOW
DSPF scanner
mode exposure
adjustment (Low
density side)
mode exposure
adjustment (Low
density side)
1 - 99
47
C
FAX SIDEB:
LOW
LOW
DSPF FAX mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
47
D
COPY SIDEB:
HIGH
HIGH
DSPF copy mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
50
E
SCAN SIDEB:
HIGH
HIGH
DSPF scanner
mode exposre
adjustment (High
density side)
mode exposre
adjustment (High
density side)
1 - 99
50
F
FAX SIDEB:
HIGH
HIGH
DSPF FAX mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
50
G
BALANCE
SIDEB: R
SIDEB: R
DSPF color
balance R
balance R
1 - 99
50
H
BALANCE
SIDEB: G
SIDEB: G
DSPF color
balance G
balance G
1 - 99
50
I
BALANCE
SIDEB: B
SIDEB: B
DSPF color
balance B
balance B
1 - 99
50
Item
Button
Display
Content
Setting
range
Default
value
A
OC
COPY SIDEA:
LOW
LOW
DSPF copy mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
42
B
SCAN SIDEA:
LOW
LOW
DSPF scanner
mode exposure
adjustment (Low
density side)
mode exposure
adjustment (Low
density side)
1 - 99
42
C
FAX SIDEA:
LOW
LOW
DSPF FAX mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
42
D
COPY SIDEA:
HIGH
HIGH
DSPF copy mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
53
E
SCAN SIDEA:
HIGH
HIGH
DSPF scanner
mode exposre
adjustment (High
density side)
mode exposre
adjustment (High
density side)
1 - 99
53
F
FAX SIDEA:
HIGH
HIGH
DSPF FAX mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
53
OK
DSPF
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<6,'($˖/2:
$˖
˖6&$16,'($˖/2:
%˖
˖)$;6,'($˖/2:
&˖
˖&23<6,'($˖+,*+
' 䋺
˖)$;6,'($˖+,*+
)˖
˖6&$16,'($˖+,*+
(˖
2.
'63)
2&
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(1763)
$˖
˷̚˹
˖&23<6,'(%˖/2:
$˖
˖6&$16,'(%˖/2:
%˖
˖)$;6,'(%˖/2:
&˖
˖&23<6,'(%˖+,*+
' 䋺
˖)$;6,'(%˖+,*+
)˖
˖6&$16,'(%˖+,*+
(˖
2.
'63)
2&
10-key
MX-4101N ADJUSTMENTS 5 – 80
2)
Press DSPF key to select the back surface copy density
adjustment mode.
adjustment mode.
3)
Select an adjustment mode with the scroll key.
To adjust the density in the low density area, select "COPY
SIDE B LOW." To adjust the density in the high density area,
select "COPY SIDE B HIGH."
To adjust the density in the low density area, select "COPY
SIDE B LOW." To adjust the density in the high density area,
select "COPY SIDE B HIGH."
4)
Enter an adjustment value with 10-key.
To increase the density, enter a greater number. To decrease
the density, enter a smaller number.
To increase the density, enter a greater number. To decrease
the density, enter a smaller number.
5)
Press [OK] key.
6)
Press [CLOSE] key to exit the simulation mode.
7)
Make a copy, and check the copy density.
Repeat the above procedures until a satisfactory result is obtained.
20-S
Auto color balance adjustment by the user
(Copy color balance auto adjustment
ENABLE setting and adjustment)
(Copy color balance auto adjustment
ENABLE setting and adjustment)
a. General
In the user program mode, the user can execute the auto color cal-
ibration (auto adjustment of the copy color balance and density).
This adjustment is to set Enable/Disable of the above user opera-
tion with SIM 26-53.
In the user program mode, the user can execute the auto color cal-
ibration (auto adjustment of the copy color balance and density).
This adjustment is to set Enable/Disable of the above user opera-
tion with SIM 26-53.
NOTE: This setting must be set to ENABLE only when the user's
understanding on the automatic adjustment of the copy
color balance and density and the user's operational ability
are judged enough to execute the adjustment.
When set to ENABLE, give enough explanations on the
operating procedures, notes, and operations to the user.
color balance and density and the user's operational ability
are judged enough to execute the adjustment.
When set to ENABLE, give enough explanations on the
operating procedures, notes, and operations to the user.
This adjustment is required in the following cases.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
* When the PCU PWB is replaced.
* When the EEPROM of the PCU PWB is replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
* When the PCU PWB is replaced.
* When the EEPROM of the PCU PWB is replaced.
b. Setting procedure
1)
1)
Enter the SIM 26-53 mode.
2)
Select ENABLE or DISABLE with 10-key.
When disabling, set to "0" (NO). When enabling, set to "1"
(Yes).
When disabling, set to "0" (NO). When enabling, set to "1"
(Yes).
3)
Press [OK] key.
When set to DISABLE, the menu of the user auto color calibration
(automatic adjustment of copy color balance and density) is not dis-
played in the user program mode.
(Auto color calibration by the user (Auto color balance adjustment))
Remark:
This adjustment is based on the service target color balance set
with SIM 63-7 and SIM 63-8. If, therefore, the above settings are
not properly performed, this adjustment cannot be made properly.
1)
(automatic adjustment of copy color balance and density) is not dis-
played in the user program mode.
(Auto color calibration by the user (Auto color balance adjustment))
Remark:
This adjustment is based on the service target color balance set
with SIM 63-7 and SIM 63-8. If, therefore, the above settings are
not properly performed, this adjustment cannot be made properly.
1)
Enter the system setting mode.
2)
Enter the copy setting mode.
3)
Press the auto color calibration key.
4)
Press [EXECUTE] key.
The color patch image (adjustment pattern) is printed out.
The color patch image (adjustment pattern) is printed out.
5)
Set the color patch image (adjustment pattern) printed in pro-
cedure 4) on the document table.
Set the patch image so that the light density area is on the left
side.
At that time, place 5 sheets of white paper on the above color
patch image (adjustment pattern).
cedure 4) on the document table.
Set the patch image so that the light density area is on the left
side.
At that time, place 5 sheets of white paper on the above color
patch image (adjustment pattern).
6)
Press [EXECUTE] key, and the copy color balance adjustment
is executed automatically. After completion of the adjustment,
the display returns to the original operation screen.
is executed automatically. After completion of the adjustment,
the display returns to the original operation screen.
A
DSPF
COPY SIDEB:
LOW
LOW
DSPF copy mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
45
B
SCAN SIDEB:
LOW
LOW
DSPF scanner
mode exposure
adjustment (Low
density side)
mode exposure
adjustment (Low
density side)
1 - 99
45
C
FAX SIDEB:
LOW
LOW
DSPF FAX mode
exposure
adjustment (Low
density side)
exposure
adjustment (Low
density side)
1 - 99
45
D
COPY SIDEB:
HIGH
HIGH
DSPF copy mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
50
E
SCAN SIDEB:
HIGH
HIGH
DSPF scanner
mode exposre
adjustment (High
density side)
mode exposre
adjustment (High
density side)
1 - 99
50
F
FAX SIDEB:
HIGH
HIGH
DSPF FAX mode
exposure
adjustment (High
density side)
exposure
adjustment (High
density side)
1 - 99
50
G
BALANCE
SIDEB: R
SIDEB: R
DSPF color
balance R
balance R
1 - 99
50
H
BALANCE
SIDEB: G
SIDEB: G
DSPF color
balance G
balance G
1 - 99
50
I
BALANCE
SIDEB: B
SIDEB: B
DSPF color
balance B
balance B
1 - 99
50
Item
Button
Display
Content
Setting
range
Default
value
OK
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&&2/25&2/,%5$7,21
$˖
˷̚˹
˖<(612
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1$%/,1*2)$8720$7,&&2/25&2/,%5$7,21
$˖
˷̚˹
˖<(612
$˖
2.
Thin line
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man13) service manuals if exist.