Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man13) Service Manual ▷ View online
MX-4101N ADJUSTMENTS 5 – 65
• Factory target in the copy color balance adjustment (SIM 46-24)
By use of SIM 63-11, one of the following color balances can be set as the factory color balance target.
Each of the three color balances cannot be changed. (Fixed)
Each of the three color balances cannot be changed. (Fixed)
• Service color balance target in the copy color balance adjust-
ment (SIM 46-24).
For the service color balance target, an optional color balance
can be adjusted with SIM 46-21 and registered with SIM 63-7.
When, however, SIM 63-8 is executed, the color balance is set to
the same balance as the factory color balance target set with
SIM 63-11.
For the service color balance target, an optional color balance
can be adjusted with SIM 46-21 and registered with SIM 63-7.
When, however, SIM 63-8 is executed, the color balance is set to
the same balance as the factory color balance target set with
SIM 63-11.
• Color balance target in the user color balance adjustment
This color balance is same as the service color balance target in
the copy color balance adjustment (SIM 46-24). When, therefore,
the service color balance target is changed, this target is also
changed accordingly.
the copy color balance adjustment (SIM 46-24). When, therefore,
the service color balance target is changed, this target is also
changed accordingly.
(Meaning of the service color balance target gamma data and the
purpose of registration)
This procedure must be executed only when the color balance is
customized with SIM 46-21. If the color balance is not customized,
this procedure is not required.
After completion of the customized color balance adjustment (Man-
ual) with SIM 46-21 according to the user's request, use SIM 63-7
to register the service color balance target data by using adjust-
ment pattern that was printed in this mode.
By this procedure, the service color balance target is revised.
It is recommendable to keep the printed adjustment pattern with
SIM 46-21. This adjustment pattern can be used to register the
same color balance target to another machine.
It is also useful to register the service color balance target data.
Do not fold it and keep it under the circumstances which protect it
from discoloration and dirt.
The service color balance target data are basically registered
immediately after the color balance adjustment (Manual) with SIM
46-21.
If a considerable time has passed after completion of the color bal-
ance adjustment (Manual) with SIM 46-21, the color balance of the
adjustment pattern at the time of adjustment differs from the color
balance of the adjustment pattern printed after a considerable time.
Never use such a pattern for the adjustment.
purpose of registration)
This procedure must be executed only when the color balance is
customized with SIM 46-21. If the color balance is not customized,
this procedure is not required.
After completion of the customized color balance adjustment (Man-
ual) with SIM 46-21 according to the user's request, use SIM 63-7
to register the service color balance target data by using adjust-
ment pattern that was printed in this mode.
By this procedure, the service color balance target is revised.
It is recommendable to keep the printed adjustment pattern with
SIM 46-21. This adjustment pattern can be used to register the
same color balance target to another machine.
It is also useful to register the service color balance target data.
Do not fold it and keep it under the circumstances which protect it
from discoloration and dirt.
The service color balance target data are basically registered
immediately after the color balance adjustment (Manual) with SIM
46-21.
If a considerable time has passed after completion of the color bal-
ance adjustment (Manual) with SIM 46-21, the color balance of the
adjustment pattern at the time of adjustment differs from the color
balance of the adjustment pattern printed after a considerable time.
Never use such a pattern for the adjustment.
The correctness of the service color balance target data can be
judges as follows.
When result of the color valance adjustment (Auto) with selecting
the service color balance target in SIM 46-24 is unsatisfactory or
abnormal.
In that case, the registered service target data for the color balance
adjustment (Auto) may be improper.
This may be caused when an improper or abnormal color balance
adjustment pattern was used to register the service color balance
target data for the color balance adjustment with SIM 63-7.
The color balance adjustment pattern used in registration was
made and printed by the color balance adjustment (Manual) with
SIM 46-21. This procedure may have been executed erroneously
judges as follows.
When result of the color valance adjustment (Auto) with selecting
the service color balance target in SIM 46-24 is unsatisfactory or
abnormal.
In that case, the registered service target data for the color balance
adjustment (Auto) may be improper.
This may be caused when an improper or abnormal color balance
adjustment pattern was used to register the service color balance
target data for the color balance adjustment with SIM 63-7.
The color balance adjustment pattern used in registration was
made and printed by the color balance adjustment (Manual) with
SIM 46-21. This procedure may have been executed erroneously
b. Setting procedure
(Setting procedure of an optional color balance (gamma) as the
service color balance target)
1)
(Setting procedure of an optional color balance (gamma) as the
service color balance target)
1)
Use SIM 46-21 (Copy color balance adjustment (manual
adjustment) mode) to print two sheets of the color patch image
(adjustment pattern).
If the color balance is shifted from the standard, an adjustment
is required. If not, an adjustment is not required. When an
optional color balance is requested by the user, make an
adjustment.
adjustment) mode) to print two sheets of the color patch image
(adjustment pattern).
If the color balance is shifted from the standard, an adjustment
is required. If not, an adjustment is not required. When an
optional color balance is requested by the user, make an
adjustment.
2)
Enter the SIM 63-7 mode.
DEF1
DEF1
Item
Content
Default
DEF2
DEF3
Factory color balance target (DEF3) =
Service color balance target/Color balance
target for the user color balance adjustment
Service color balance target/Color balance
target for the user color balance adjustment
The engine color balance adjustment target in the automatic color balance
operation is slightly shifted to Magenta. When this target is selected, the
color balance is converted into natural gray color balance by the color
correction table in an actual copy mode and print is made.
operation is slightly shifted to Magenta. When this target is selected, the
color balance is converted into natural gray color balance by the color
correction table in an actual copy mode and print is made.
The engine color balance adjustment target in the automatic color balance
operation is slightly shifted to natural gray color balance. When this target is
selected, the color balance is slightly shifted to Cyan by the color correction
table in an actual copy mode and print is made.
operation is slightly shifted to natural gray color balance. When this target is
selected, the color balance is slightly shifted to Cyan by the color correction
table in an actual copy mode and print is made.
The engine color balance adjustment target in the automatic color balance
operation is slightly shifted to Cyan. When this target is selected, the color
balance is converted into the color balance with enhanced Cyan by the color
correction table in an actual copy mode and print is made.
operation is slightly shifted to Cyan. When this target is selected, the color
balance is converted into the color balance with enhanced Cyan by the color
correction table in an actual copy mode and print is made.
SIM63-8
SIM63-8
SIM63-8
Factory color balance target (DEF2) =
Service color balance target/Color balance
target for the user color balance adjustment
Service color balance target/Color balance
target for the user color balance adjustment
Factory color balance target
(DEF1) = Service color balance
target/Color balance target for the
user color balance adjustment
(DEF1) = Service color balance
target/Color balance target for the
user color balance adjustment
Hue
+b* Direction of Yellow
Direction of Blue
(A)
Factory color balance target
(DEF2)
(DEF2)
Factory color balance target
(DEF1)
(DEF1)
Direction
of Red
of Red
Factory color balance target
(DEF3)
(DEF3)
Direction
of Green
of Green
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(57$5*(72)&2/25&$/,%6(7836(59,&(
6(783
%&'()
*+,-.
㩺㪣012
.
&
0
<
MX-4101N ADJUSTMENTS 5 – 66
3)
Press [SETUP] key.
4)
Set the color patch image (adjustment pattern) correctly
adjusted and printed in the copy color balance adjustment
(Manual adjustment) (SIM 46-21) (ADJ 20C) on the document
table.
The color patch image (adjustment pattern) printed with SIM
64-7 can be used instead. In this case, however, check that the
printed pattern is normal.
(When the color patch image (adjustment pattern) is printed by
SIM 64-7, set the item B (PROC ADJ) to "0 (YES)" and press
[EXECUTE] key to print.)
A color patch image (adjustment pattern) printed by another
machine can be used.
Set the pattern so that the light density side is on the left side.
Place 5 sheets of white paper on the color patch image
(adjustment pattern).
If the color balance could not be adjusted satisfactorily with
SIM 46-21 (Color balance adjustment (Manual)), do not exe-
cute SIM 63-7 to register the service color balance target data.
adjusted and printed in the copy color balance adjustment
(Manual adjustment) (SIM 46-21) (ADJ 20C) on the document
table.
The color patch image (adjustment pattern) printed with SIM
64-7 can be used instead. In this case, however, check that the
printed pattern is normal.
(When the color patch image (adjustment pattern) is printed by
SIM 64-7, set the item B (PROC ADJ) to "0 (YES)" and press
[EXECUTE] key to print.)
A color patch image (adjustment pattern) printed by another
machine can be used.
Set the pattern so that the light density side is on the left side.
Place 5 sheets of white paper on the color patch image
(adjustment pattern).
If the color balance could not be adjusted satisfactorily with
SIM 46-21 (Color balance adjustment (Manual)), do not exe-
cute SIM 63-7 to register the service color balance target data.
5)
Press [EXECUTE] key.
The color patch image (adjustment pattern) is read.
6)
Press [REPEAT] key, set the second color patch image
(adjustment pattern), and execute the procedure 5) again.
(adjustment pattern), and execute the procedure 5) again.
The color balance (gamma) target set level of each color
(KCMY) can be checked with K/C/M/Y keys.
Check that the set level is increased in the sequence of B - Q
(MAX). If there is no variation or variation is reversed, it is
judged as abnormal.
In case of an abnormality, repair the problem and try again.
(KCMY) can be checked with K/C/M/Y keys.
Check that the set level is increased in the sequence of B - Q
(MAX). If there is no variation or variation is reversed, it is
judged as abnormal.
In case of an abnormality, repair the problem and try again.
7)
Press [OK] key.
The color balance (gamma) of the color patch image (adjust-
ment pattern) used in the procedure 5) is set as the service tar-
get.
The color balance (gamma) of the color patch image (adjust-
ment pattern) used in the procedure 5) is set as the service tar-
get.
(Procedures to set the service color balance target and the color
balance target for the user color balance adjustment to the same
color balance as the factory color balance target)
This procedure must not be executed when the copy color balance
was adjusted with SIM 46-21 to a unique color balance requested
by the user and it was registered as the service color balance tar-
get with SIM 63-7.
balance target for the user color balance adjustment to the same
color balance as the factory color balance target)
This procedure must not be executed when the copy color balance
was adjusted with SIM 46-21 to a unique color balance requested
by the user and it was registered as the service color balance tar-
get with SIM 63-7.
* When the factory color balance target is changed with SIM 63-11,
be sure to execute this procedure.
1)
Enter the SIM 63-8 mode.
2)
Press [EXECUTE] key.
3)
Press [YES] key.
The service color balance target and the color balance target for
the user color balance adjustment are set to the same color bal-
ance as the factory color balance target.
the user color balance adjustment are set to the same color bal-
ance as the factory color balance target.
20-D
Copy density adjustment (Each color copy
mode) (Whole adjustment) (Normally
unnecessary to adjust)
mode) (Whole adjustment) (Normally
unnecessary to adjust)
This adjustment is needed in the following situations:
* When there is necessity to change the copy density of the low
* When there is necessity to change the copy density of the low
density and high density part at each copy density individually.
* When there is necessity to change the density gradient of the
copy by each the copy mode individually.
* When there is necessity to change all copy density by each the
copy mode individually.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
The density is adjusted in each copy mode individually. Normally
individual adjustments are not required. When there is a request
from the user, execute this adjustment.
1)
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
The density is adjusted in each copy mode individually. Normally
individual adjustments are not required. When there is a request
from the user, execute this adjustment.
1)
Enter the SIM 46-1 mode.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(57$5*(72)&2/25&$/,%6(7836(59,&(
(;(&87(
6(77+(&+$57213/$7(1$1'728&+>(;(&87(@
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6&$11(57$5*(72)&2/25&$/,%6(7836(59,&(
(;(&87(
12:&+$573$7&+5($',1*
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
67$1'$5'6&$11(57$5*(76(77,1*6(59,&(
(;(&87(
$5(<28685("
<(6
12
㩷
OK
㪈㪇㪄㫂㪼㫐
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17&2/25>&23<@
$˖
˷̚˹
˖$872
$˖
˖7(;7
%˖
˖7(;735,17('ǂ3+272
&˖
˖7(;73+272
'˖
˖3+272*5$3+
)˖
˖35,17('ǂ3+272
(˖
˖0$3
*˖
˖/,*+7
+˖
˖7(;7&23<ǂ72ǂ&23<
,˖
˖7(;735,17('ǂ3+272&23<ǂ72ǂ&23<
-˖
˖35,17('ǂ3+272&23<ǂ72ǂ&23<
.˖
˖7(;7&2/25ǂ721(ǂ(1+$1&(0(17
/˖
2.
+,*+
/2:
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17&2/25>&23<@
$˖
˷̚˹
˖$872
$˖
˖7(;7
%˖
˖7(;735,17('ǂ3+272
&˖
˖7(;73+272
'˖
˖3+272*5$3+
)˖
˖35,17('ǂ3+272
(˖
˖0$3
*˖
˖/,*+7
+˖
˖7(;7&23<ǂ72ǂ&23<
,˖
˖7(;735,17('ǂ3+272&23<ǂ72ǂ&23<
-˖
˖35,17('ǂ3+272&23<ǂ72ǂ&23<
.˖
˖7(;7&2/25ǂ721(ǂ(1+$1&(0(17
/˖
2.
+,*+
/2:
MX-4101N ADJUSTMENTS 5 – 67
2)
Select the copy mode to be adjusted with the scroll key.
3)
Enter the adjustment value with 10-key and press [OK] key.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
4)
Press [CLOSE] key in this simulation mode to jump to the nor-
mal copy mode. Make a copy and check the adjustment result
Switch the simulation mode and the normal copy mode alter-
nately, and adjust and check the adjustment result.
Repeat switching the adjustment mode (SIM 46-1) and the
normal copy mode and changing the adjustment value and
checking the adjustment result until a satisfactory result is
obtained.
To increase the density, increase the adjustment value. To
decrease the density, decrease the adjustment value.
mal copy mode. Make a copy and check the adjustment result
Switch the simulation mode and the normal copy mode alter-
nately, and adjust and check the adjustment result.
Repeat switching the adjustment mode (SIM 46-1) and the
normal copy mode and changing the adjustment value and
checking the adjustment result until a satisfactory result is
obtained.
To increase the density, increase the adjustment value. To
decrease the density, decrease the adjustment value.
20-E
Copy density adjustment (Each
monochrome copy mode) (Whole
adjustment) (Normally unnecessary to
adjust)
monochrome copy mode) (Whole
adjustment) (Normally unnecessary to
adjust)
This adjustment is needed in the following situations:
* When there is necessity to change copy density of the low den-
* When there is necessity to change copy density of the low den-
sity and high density part at each copy mode individually.
* When there is necessity to change the density gradient of the
copy by each the copy mode individually.
* When there is necessity to change all copy density by each the
copy mode individually.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
The density is adjusted in each copy mode individually. Normally
individual adjustments are not required. When there is a request
from the user, execute this adjustment.
1)
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
The density is adjusted in each copy mode individually. Normally
individual adjustments are not required. When there is a request
from the user, execute this adjustment.
1)
Enter the SIM 46-2 mode.
Display/Item
Content
Setting
range
Default
A
AUTO
Auto
LOW
1 - 99
50
HIGH
1 - 99
50
B
TEXT
Text
LOW
1 - 99
50
HIGH
1 - 99
50
C
TEXT/PRINTED
PHOTO
PHOTO
Text/Printed
Photo
Photo
LOW
1 - 99
50
HIGH
1 - 99
50
D
TEXT/PHOTO
Text/Photograph
LOW
1 - 99
50
HIGH
1 - 99
50
E
PRINTED PHOTO
Printed Photo
LOW
1 - 99
50
HIGH
1 - 99
50
F
PHOTOGRAPH
Photograph
LOW
1 - 99
50
HIGH
1 - 99
50
G
MAP
Map
LOW
1 - 99
50
HIGH
1 - 99
50
H
LIGHT
Light document
LOW
1 - 99
50
HIGH
1 - 99
50
I
TEXT
(COPY TO COPY)
(COPY TO COPY)
Text (Copy
document)
document)
LOW
1 - 99
50
HIGH
1 - 99
50
J
TEXT/PRINTED
PHOTO
(COPY TO COPY)
PHOTO
(COPY TO COPY)
Text/Printed
Photo (Copy
document)
Photo (Copy
document)
LOW
1 - 99
50
HIGH
1 - 99
50
K
PRINTED PHOTO
(COPY TO COPY)
(COPY TO COPY)
Printed Photo
(Copy document)
(Copy document)
LOW
1 - 99
50
HIGH
1 - 99
50
L
TEXT
(COLOR TONE
ENHANCEMENT)
(COLOR TONE
ENHANCEMENT)
Text
(Color tone
enhancement)
(Color tone
enhancement)
LOW
1 - 99
50
HIGH
1 - 99
50
M
TEXT/PRINTED
PHOTO
(COLOR TONE
ENHANCEMENT)
PHOTO
(COLOR TONE
ENHANCEMENT)
Text/Printed
Photo
(Color tone
enhancement)
Photo
(Color tone
enhancement)
LOW
1 - 99
50
HIGH
1 - 99
50
N
TEXT/PHOTO
(COLOR TONE
ENHANCEMENT)
(COLOR TONE
ENHANCEMENT)
Text/Photograph
(Color tone
enhancement)
(Color tone
enhancement)
LOW
1 - 99
50
HIGH
1 - 99
50
O
PRINTED PHOTO
(COLOR TONE
ENHANCEMENT)
(COLOR TONE
ENHANCEMENT)
Printed Photo
(Color tone
enhancement)
(Color tone
enhancement)
LOW
1 - 99
50
HIGH
1 - 99
50
P
PHOTOGRAPH
(COLOR TONE
ENHANCEMENT)
(COLOR TONE
ENHANCEMENT)
Photograph
(Color tone
enhancement)
(Color tone
enhancement)
LOW
1 - 99
50
HIGH
1 - 99
50
Q
MAP
(COLOR TONE
ENHANCEMENT)
(COLOR TONE
ENHANCEMENT)
Map
(Color tone
enhancement)
(Color tone
enhancement)
LOW
1 - 99
50
HIGH
1 - 99
50
R
SINGLE COLOR
Single color
LOW
1 - 99
50
HIGH
1 - 99
50
S
SINGLE COLOR
(COPY TO COPY)
(COPY TO COPY)
Single color
(Copy document)
(Copy document)
LOW
1 - 99
50
HIGH
1 - 99
50
T
TWO COLOR
Two-color
(Red/Black) copy
(Red/Black) copy
LOW
1 - 99
50
HIGH
1 - 99
50
U
TWO COLOR
(COPY TO COPY)
(COPY TO COPY)
Two-color
(Red/Black) copy
(Copy document)
(Red/Black) copy
(Copy document)
LOW
1 - 99
50
HIGH
1 - 99
50
OK
㪈㪇㪄㫂㪼㫐
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17%:>&23<@
$˖
˷̚˹
˖$872
$˖
˖$872
%˖
˖7(;7
&˖
˖7(;735,17('3+272
'˖
˖35,17('3+272
)˖
˖7(;73+272
(˖
˖3+272*5$3+
*˖
˖0$3
+˖
˖7(;7&23<72&23<
,˖
˖7(;735,17('3+272&23<72&23<
-˖
˖35,17('3+272&23<72&23<
.˖
˖/,*+7
/˖
2.
+,*+
/2:
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(;32685($'-8670(17%:>&23<@
$˖
˷̚˹
˖$872
$˖
˖$872
%˖
˖7(;7
&˖
˖7(;735,17('3+272
'˖
˖35,17('3+272
)˖
˖7(;73+272
(˖
˖3+272*5$3+
*˖
˖0$3
+˖
˖7(;7&23<72&23<
,˖
˖7(;735,17('3+272&23<72&23<
-˖
˖35,17('3+272&23<72&23<
.˖
˖/,*+7
/˖
2.
+,*+
/2:
MX-4101N ADJUSTMENTS 5 – 68
2)
Select the copy mode to be adjusted with the scroll key.
3)
Enter the adjustment value with 10-key and press [OK] key.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
When adjusting the copy density on the low density part, select
"LOW" mode and change the adjustment value. When adjust-
ing the copy density on the high density part, select "HIGH"
mode and change the adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy
density is decreased.
4)
Press [CLOSE] key in this simulation mode to jump to the nor-
mal copy mode. Make a copy and check the adjustment result
Switch the simulation mode and the normal copy mode alter-
nately, and adjust and check the adjustment result.
Repeat switching the adjustment mode (SIM 46-1) and the
normal copy mode and changing the adjustment value and
checking the adjustment result until a satisfactory result is
obtained.
To increase the density, increase the adjustment value. To
decrease the density, decrease the adjustment value.
mal copy mode. Make a copy and check the adjustment result
Switch the simulation mode and the normal copy mode alter-
nately, and adjust and check the adjustment result.
Repeat switching the adjustment mode (SIM 46-1) and the
normal copy mode and changing the adjustment value and
checking the adjustment result until a satisfactory result is
obtained.
To increase the density, increase the adjustment value. To
decrease the density, decrease the adjustment value.
20-F
Copy color balance adjustment (Color
balance adjustment at each density level in
each color copy mode)
(Normally not required)
balance adjustment at each density level in
each color copy mode)
(Normally not required)
This adjustment is needed in the following situations:
* When there is necessity to change the color balance and gamma
* When there is necessity to change the color balance and gamma
by each the copy mode individually.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
This is to adjust the color balance at each density level in each
color copy mode. Normally individual adjustments are not required.
This adjustment is executed when there is a request from the user.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
This is to adjust the color balance at each density level in each
color copy mode. Normally individual adjustments are not required.
This adjustment is executed when there is a request from the user.
1)
Enter the SIM 46-10 mode.
2)
Select the copy mode to be adjusted with the mode key.
3)
Select a color to change the adjustment value with the color
key.
key.
4)
Select the density level (point) to be adjusted with the scroll
key.
key.
Display/Item
Content
Setting
range
Default
A
AUTO1
Auto 1
LOW
1 - 99
50
HIGH
1 - 99
50
B
AUTO2
Auto 2
LOW
1 - 99
50
HIGH
1 - 99
50
C
TEXT
Text
LOW
1 - 99
50
HIGH
1 - 99
50
D
TEXT/PRINTED
PHOTO
PHOTO
Text/Printed
Photo
Photo
LOW
1 - 99
50
HIGH
1 - 99
50
E
TEXT/PHOTO
Text/Photograph
LOW
1 - 99
50
HIGH
1 - 99
50
F
PRINTED PHOTO
Printed Photo
LOW
1 - 99
50
HIGH
1 - 99
50
G
PHOTOGRAPH
Photograph
LOW
1 - 99
50
HIGH
1 - 99
50
H
MAP
Map
LOW
1 - 99
50
HIGH
1 - 99
50
I
TEXT
(COPY TO COPY)
(COPY TO COPY)
Text (Copy
document)
document)
LOW
1 - 99
50
HIGH
1 - 99
50
J
TEXT/PRINTED
PHOTO
(COPY TO COPY)
PHOTO
(COPY TO COPY)
Text/Printed
Photo (Copy
document)
Photo (Copy
document)
LOW
1 - 99
50
HIGH
1 - 99
50
K
PRINTED PHOTO
(COPY TO COPY)
(COPY TO COPY)
Printed Photo
(Copy document)
(Copy document)
LOW
1 - 99
50
HIGH
1 - 99
50
L
LIGHT
Light document
LOW
1 - 99
50
HIGH
1 - 99
50
Item/Display
Density level
(Point)
Adjustment
value range
value range
Default
A
POINT1
Point 1
245 - 755
500
B
POINT2
Point 2
245 - 755
500
C
POINT3
Point 3
245 - 755
500
D
POINT4
Point 4
245 - 755
500
E
POINT5
Point 5
245 - 755
500
F
POINT6
Point 6
245 - 755
500
G
POINT7
Point 7
245 - 755
500
H
POINT8
Point 8
245 - 755
500
I
POINT9
Point 9
245 - 755
500
J
POINT10
Point 10
245 - 755
500
10-key
OK
C
TEXT
EXECUTE
EXECUTE
or end of print
[SYSTEM
SETTINGS] key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(&2/25%$/$1&(0$18$/$'-8670(17
(;(&87(
7(;7
7(;7357ǂ3+272
3+272ˇ7(;73+272
35,17('ǂ3+272
0$3
/,*+7
&23<ǂ25*
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(&2/25%$/$1&(0$18$/$'-8670(17>7(;7@
$˖
˷̚˹
˖32,17
$˖
˖32,17
%˖
˖32,17
&˖
˖32,17
'˖
˖32,17
)˖
˖32,17
(˖
˖32,17
*˖
˖32,17
+˖
˖32,17
,˖
˖32,17
-˖
˖32,17
.˖
˖32,17
/˖
.
&
0
<
2.
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(&2/25%$/$1&(0$18$/$'-8670(17>7(;7@
$˖
˷̚˹
˖32,17
$˖
˖32,17
%˖
˖32,17
&˖
˖32,17
'˖
˖32,17
)˖
˖32,17
(˖
˖32,17
*˖
˖32,17
+˖
˖32,17
,˖
˖32,17
-˖
˖32,17
.˖
˖32,17
/˖
.
&
0
<
2.
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(&2/25%$/$1&(0$18$/$'-8670(17>7(;7@
$˖
˷̚˹
˖32,17
$˖
˖32,17
%˖
˖32,17
&˖
˖32,17
'˖
˖32,17
)˖
˖32,17
(˖
˖32,17
*˖
˖32,17
+˖
˖32,17
,˖
˖32,17
-˖
˖32,17
.˖
˖32,17
/˖
.
&
0
<
2.
(;(&87(
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man13) service manuals if exist.