Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man11) Service Manual ▷ View online
MX3500N MX-FXX1 14 – 1
MX3500N
Service Manual
[14] MX-FXX1
1. Unpacking
A. Parts included
2. Installation
<Note before installation>
• Start installation after checking that the LINE indicator and the
• Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
blinking.
A. Turn off the power switches of the main unit.
1)
Turn the power switch located on the operation panel to the
“OFF” position.
“OFF” position.
2)
After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the “OFF” opsi-
tion.
front cabinet and turn the main power switch to the “OFF” opsi-
tion.
3)
Remove the power plug of the main unit from the outlet.
B. Attach the fax box unit to the rear part of the
main unit.
1)
Remove the two screws from the rear cabinet of the main unit.
2)
Attach the supplied step screw to one of the two positions from
which the screws are removed.
which the screws are removed.
3)
Insert the step screw into the mounting hole of the fax box unit.
4)
Use a screw that has been removed in step 1) to secure the
fax box unit.
fax box unit.
C. Pull out the control PWB.
1)
Push the location indicated in the illustration to unlock, and
remove the ozone filter cover from the right rear cabinet.
remove the ozone filter cover from the right rear cabinet.
2)
Remove the screw from the right rear cabinet and remove the
right rear cabinet.
right rear cabinet.
MX3500N MX-FXX1 14 – 2
3)
Remove the two screws from the control PWB unit.
4)
Pull out the control PWB unit.
D. Attach the FAX memory.
1)
Install the FAX memory to the socket on the controller PWB as
shown in the figure below so that the memory notch is on the
right side.
shown in the figure below so that the memory notch is on the
right side.
E. Attach the interface cable.
1)
Connect the interface cable to the control PWB unit.
[Note] Check that the connector is not obliquely inserted.
[Note] Check that the connector is not obliquely inserted.
2)
Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.
metal on the control PWB unit.
3)
Attach the snap band to the sheet metal of the control PWB
unit.
unit.
F. Attach the control PWB and the right rear
cabinet.
1)
Push the control PWB unit into the main unit and secure it with
the two screws.
the two screws.
2)
Cut out the cut-out portion of the right rear cabinet.
3)
Fit the interface cable into the opening that has been cut.
4)
Attach the right rear cabinet cover to the main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
5)
Secure the right rear cabinet with the screw.
6)
Attach the ozone filter cover to the main unit.
MX3500N MX-FXX1 14 – 3
G. Turn on the main power switch of the main
unit.
1)
Insert the power plug of the main unit to the outlet.
2)
Turn on the main power switch.
3)
Turn on the power switch located on the operation panel.
H. Set the destination and the logo type.
1)
Switch the operation panel to the copy mode and use the key
operation [P], [
operation [P], [
∗], [C], and [∗] to enter the simulation mode.
2)
Use the numeric keys to enter [26] in the main code entry
screen shown below and press the [START] key.
screen shown below and press the [START] key.
3)
Use the numeric keys to enter [06] in the sub-code entry
screen shown below and press the [START] key.
screen shown below and press the [START] key.
4)
Press the desired destination on the touch panel and press
[EXECUTE] to highlight it.
[EXECUTE] to highlight it.
5)
Press the [CA] key or the [SYSTEM SETTINGS] key to exit
from the simulation mode. The message [PLEASE TURN
MAIN POWER OFF THEN ON] is displayed.
Restart the machine to change the destination.
from the simulation mode. The message [PLEASE TURN
MAIN POWER OFF THEN ON] is displayed.
Restart the machine to change the destination.
• List of destinations
I. Clear the FAX related software switches.
1)
Switch the operation panel to the copy mode and use the key
operation [P], [
operation [P], [
∗], [C], and [∗] to enter the simulation mode.
2)
Use the numeric keys to enter [66] in the main code entry
screen shown below and press the [START] key.
screen shown below and press the [START] key.
3)
Use the numeric keys to enter [02] in the sub-code entry
screen shown below and press the [START] key.
screen shown below and press the [START] key.
4)
Use numeric keys [0] and [1] to enter the desired 8-digit coun-
try code.
After entry, press [SET], [EXECUTE], and [YES] in this order.
try code.
After entry, press [SET], [EXECUTE], and [YES] in this order.
• Country code list screen
* Press the [DEST CODE] button on the initial screen to move to
* Press the [DEST CODE] button on the initial screen to move to
the country code list screen.
To return to the input screen, press the [BACK] button.
To return to the input screen, press the [BACK] button.
Display
Description
U.S.A
U.S.A.
CANADA
Canada
INCH
Inch system, other destinations
JAPAN
Japan
AB_B
AB system (B5 size detectable), other destinations
EUROPE
Europe
U.K.
U.K.
AUS.
Australia
AB_A
AB system (A5 size detectable), other destinations
CHINA
China
Country code list
JAPAN
: 00000000
FINLAND
: 00111100
U.S.A.
: 10110101
NORWAY
: 10000010
AUSTRALIA
: 00001001
DENMARK
: 00110001
U.K.
: 10110100
NETHERLANDS
: 01111011
FRANCE
: 00111101
ITALY
: 01011001
GERMANY
: 00000100
SWITZERLAND
: 10100110
SWEDEN
: 10100101
AUSTRIA
: 00001010
NEWZEALAND
: 01111110
INDONESIA
: 01010100
CHINA
: 00100110
THAILAND
: 10101001
SINGAPORE
: 10011100
MALAYSIA
: 01101100
TW
: 11111110
INDIA
: 01010011
OTHER1
: 11111101
PHILIPPINES
: 10001001
OTHER2
: 11111100
HONGKONG
: 01010000
OTHER3
: 11111011
MX3500N MX-FXX1 14 – 4
J. Clear the image memory.
1)
Switch the operation panel to the copy mode and use the key
operation [P], [
operation [P], [
∗], [C], and [∗] to enter the simulation mode.
2)
Use the numeric keys to enter [66] in the main code entry
screen shown below and press the [START] key.
screen shown below and press the [START] key.
3)
Use the numeric keys to enter [10] in the sub-code entry
screen shown below and press the [START] key.
screen shown below and press the [START] key.
4)
In the submenu screen shown below, press [EXECUTE] on the
touch panel.
After [YES] on the panel lights up, press it.
touch panel.
After [YES] on the panel lights up, press it.
5)
The screen shown below is displayed and memory clear oper-
ation is executed.
ation is executed.
6)
After several minutes, memory clear operation is completed
and the [YES] button goes out. Press the [CA] key to exit from
the simulation mode.
Then the main unit is automatically rebooted.
and the [YES] button goes out. Press the [CA] key to exit from
the simulation mode.
Then the main unit is automatically rebooted.
K. Connect the line cable to the fax box unit.
Connect the line cable of the line side to the modular jack indicated
with “LINE.”
with “LINE.”
• For using an external telephone:
For using an external telephone, wind the line cable around the
supplied ferrite core by two turns and connect the cable to the
modular jack indicated with “TEL.”
supplied ferrite core by two turns and connect the cable to the
modular jack indicated with “TEL.”
Click on the first or last page to see other MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man11) service manuals if exist.