DOWNLOAD Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man11) Service Manual ↓ Size: 18 MB | Pages: 72 in PDF or view online for FREE

MX3500N  MX-FRX2, MX-FRX2U  9 – 3

• If the fax box unit is installed, carry out steps 1), 2), and 3)

1)

Connect the interface cable to the control PWB unit.

2)

Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.

3)

Attach the snap band to the sheet metal of the control PWB
unit.

4)

Push the control PWB unit into the main unit.

5)

Secure the unit with the two screws.

• If the fax box unit is installed, carry out step 6) addition-

6)

Fit the interface cable into the right rear cabinet cover.

7)

Attach the right rear cabinet cover to the main unit.
At this time, check that the four hooks are properly fitted to the
main unit.

8)

Secure the right rear cabinet with the screw.

9)

Attach the ozone filter cover to the main unit.

• Reconnect the cables that have been removed in step B to

1)

Insert the power plug of the main unit to the outlet.

2)

Turn on the main power switch.

3)

Turn on the power switch located on the operation panel.

1)

To enable the data security function, use the keys on the oper-
ation panel to enter the product key.
a)

Touch [Product Key].

b)

Enter the product key with the 10-key, and touch [Enter]
key.

2)

After completing product key entry, turn off the power switch on
the operation panel of the main unit and then turn off the main
power switch.
Then, turn on the main power switch and then turn on the
power switch on the operation panel of the main unit again.
After the power switches are turned on, message "Please
wait." may appear and encryption and deletion of data may
take several minutes before the main unit starts.

Operation of the data security function can be set with System Set-
tings (Administrator).
For details, see the MX-FRX1U operation manual, and check the
operation.
If some files have been stored using the document filing function
(including the quick file function) before installation of MX-FRX1/
MX-FRX1U, be sure to execute [Clear All Memory] after installation
to delete all the stored files.
Restore the stored back up data into the memory (including HDD)
of the main unit.

CAUTION: For acquisition of the product key, the application

Normally only the check procedures (steps 1) and 2)) of the docu-
ment control function are required. If the control pattern is not
detected, perform the adjustment procedures of simulations (steps
3) and later).
For details of the operations, refer to the Operation Manual.
1)

Enable the document control function.
Touch [SYSTEM SETTINGS] key 

→ [DOCUMENT CONTROL

SETTING] key 

→ each mode key to perform each setting and

enable the document control function.

MX3500N  MX-FRX2, MX-FRX2U  9 – 4

2)

Check the document control function.
a)

Make a color copy of the control pattern in [Y] (yellow) on
white paper. Copy the output paper again.

b)

[Check the document.] is displayed on the touch panel. If
no print is made, the operation is normally completed.

c)

If any copy is made in step b), got to the simulation mode
and perform the control pattern adjustment.

3)

Perform SIM55-1 to adjust the control pattern.
a)

Use [Numeral] key (10-key) to select SIM55, and press
[BLACK/WHITE START] (

) key.

b)

Use [Numeral] key (10-key) to select [1], and press
[BLACK/WHITE START] (

) key.

c)

Check to confirm that [SW No.] is highlighted, and press
[Numeral] key (10-key) to select [1].

d)

Select [DATA] on the touch panel, and check to confirm
that the color is highlighted and the 8bit figure is dis-
played.

e)

Change the 6 bit – 8 bit with [Numeral] key (10-key), and
press [BLACK/WHITE START] (

) key to determine.

Basically, the greater the figure is, the higher the density
is.

4)

After completion of the control pattern adjustment, check the
document control function again.
After completion of the adjustment, perform step 2). If [Check
the document.] is displayed, the adjustment of [Y] (yellow) is
completed.
If copy is outputted, repeat the procedures of steps 2) and 3).

5)

Use the values after the adjustments to check the operations
of all the colors.
Check the document control function of [Y] (Yellow), [C]
(Cyan), and [Bk] (Black) in this sequence with the values after
adjustments.
If there is a copy output in any color, use the adjustment values
of one-step greater level and check all the colors again.
If [Check the document.] is displayed in the adjustments of all
the colors, the adjustments are completed.
With the above procedures, the check and adjustments of the
document control function are completed.

SIMULATION NO.55-01

TEST

ENGINE

SOFT

SW.

SETTING

CLOSE

EXECUTE

SW NO.

01

(SW No.1-16)

DATA

1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8

0

SIMULATION NO.55-01

TEST

ENGINE

SOFT

SW.

SETTING

CLOSE

EXECUTE

SW NO.

01

(SW No.1-16)

DATA

0 0 0 0 0 0 0 0

1 2 3 4 5 6 7 8

0

SIMULATION NO.55-01

TEST

ENGINE

SOFT

SW.

SETTING

CLOSE

EXECUTE

SW NO.

01

(SW No.1-16)

DATA

0 0 0 0 0 0 0 0

1 2 3 4 5 6 7 8

0

0 0 0 0 0 0 0 0

1 2 3 4 5 6 7 8

0 0 0 0 0 1 1 1

1 2 3 4 5 6 7 8

Small

Great

MX3500N  MX-PKX1  10 – 1

MX3500N

Service Manual

 

NOTE: To set up the PS driver, do not use the CD-ROM which is

included in the MX-PKX1 but use the CD-ROM which is
included in the MX-PBX1.

NOTE: To enable PS3, the product key must be acquired. (For

details of the acquiring method of the product key, refer to
the distributor.)
Write down the acquired product key on the product key
sheet and pass it to the user.

1)

To enable PS3, enter the product key by the key operation of
the copier machine.
a) Touch [PRODUCT KEY INPUT].
b) Enter the product key with the 10-key, and touch [OK] key.

2)

After completion of the product key entry, turn OFF the power
switch and the main power switch and turn them ON.

1)

Print the test page in PS3 fonts by the key operation of the
operation panel. (Select the PS font list by the procedures
described in the data list print printer test page of the system
setup guide.)
Check to confirm that printing is made normally.

1

CD-ROM (For Screen Font)

1

2

Product key sheet

1

1

2

APPLICATION
NUMBER

MACHINE
SERIAL
NUMBER

PRODUCT
KEY

Please keep below important information.
This information will use for other products.

MX3500N  AR-PF1  11 – 1

MX3500N

Service Manual

 

1)

Turn OFF the main switch of the copier, and disconnect the
power plug of the copier from the power outlet.

2)

Remove the screw, and remove the rear cabinet.

3)

Remove the connector and the screw, and remove the MFP
PWB shield plate upper.

4)

Install the barcode font ROM PWB to the barcode connector. 
* Check to confirm that the silver push lever extends out when

the PWB is installed.

* The connector position is indicated by the silk print on the

PWB.

5)

Install the MFP PWB shield plate upper and connect the con-
nector. 

6)

Install the rear cabinet.

7)

Insert the power plug of the copier into the power outlet. Turn
ON the power switch and perform the following procedures.

1)

PCL expansion font list check
Select the PCL expansion font list by the procedures described
in the printer test page in the system setup guide.
Check to confirm that the barcode font list is printed.

1

CD-ROM

1

2

Operation Manual

1

AR-PF1 barcode font ROM PWB

1

2

BOOT

BARCODE

PCL/BUMON

PS KANJI

PROGRAM

FAX IMG EXT