Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man11) Service Manual ▷ View online
MX3500N MX-FNX1 5 – 2
2. Installation
<Note before installation>
* Before starting installation, check to insure that the data lamp on
* Before starting installation, check to insure that the data lamp on
the operation panel does not light up or blink.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Open the front cabinet.
Turn OFF the power switch in the front cabinet of the main unit.
Turn OFF the power switch in the front cabinet of the main unit.
3)
Remove the earth cord and disconnect the power plug of the
main unit from the power outlet.
main unit from the power outlet.
B. Removal of the paper holding arm unit
1)
Push up the section A to disengage the pawl, and remove the
paper holding arm and the paper holding arm holder together
as a unit.
* Be careful to remove both of the paper holding arm (which is
paper holding arm and the paper holding arm holder together
as a unit.
* Be careful to remove both of the paper holding arm (which is
easily removed alone) and the paper holding arm holder.
C. Installation of the inner finisher
1)
Open the front cover.
2)
Remove two screws, and remove the front cabinet upper.
OFF
OFF
OFF
2
1
A
MX3500N MX-FNX1 5 – 3
3)
Disengage two pawls, and remove the paper exit tray cover.
4)
Remove four screws, and remove the paper exit tray.
* When removing the paper exit tray, there is no need to
* When removing the paper exit tray, there is no need to
remove the screws in the section (A).
5)
Remove the paper exit full detection actuator.
6)
Engage the projection on the main unit frame with the hole in
the finisher fixing plate (package part No. 1).
the finisher fixing plate (package part No. 1).
7)
Fix the right cover plate with the fixing screw (package part No.
8).
8).
* Fix the side plate of the paper exit shifter with the fixing
guide.
8)
Install the front slide rail (A) (package part No. 2) with the three
fixing screws (package part No. 8), and install the left front
cover (B) (package part No. 6) with one fixing screw (package
part No. 8).
fixing screws (package part No. 8), and install the left front
cover (B) (package part No. 6) with one fixing screw (package
part No. 8).
9)
Fix the dummy punch unit (package part No. 3) with the fixing
screw (package part No. 8).
screw (package part No. 8).
10) Check to insure that the slide roller is in the rail groove, and
insert the inner finisher.
11) Fix the rear slide rail with the fixing screw (package part No. 8).
A
A
B
MX3500N MX-FNX1 5 – 4
12) After pushing the intermediate rail of accuride, insert the fin-
isher slide stopper (package part No. 7) between the rear slide
rail and the accuride.
Fix it with the coin screw (package part No. 10).
rail and the accuride.
Fix it with the coin screw (package part No. 10).
13) Install the front open/close cover (package part No. 4) to the
front rail stay rotating shaft, and fix it with the resin clip (pack-
age part No. 9).
age part No. 9).
14) Fix the punch cover (package part No. 5) together with the
band (metal fixture) with the fixing screw (package part No. 8).
15) Install the front cabinet upper with two screws.
D. Connector connection
1)
Remove the protection material and fixing tape.
2)
Remove the screw, and remove the connector cover.
3)
Connect the finisher connector with the main unit connector,
and tighten with a screw.
and tighten with a screw.
E. Staple position label attachment
1)
Attach the label to the position indicated in the figure.
[For scanner] (package part No. 11)
[For scanner] (package part No. 11)
1
2
1
2
1
2
Label attachment
reference
reference
* Corner of the
"upper cabinet rear"
Corner R end fitting
Corner R end fitting
MX3500N MX-FNX1 5 – 5
[For RSPF/DSPF] (package part No. 12)
F. Turn on the power of the main unit
1)
Connect the earth cord, and insert the power plug of the main
unit into the power outlet.
unit into the power outlet.
2)
Open the front cabinet.
Turn ON the power switch in the front cabinet of the main unit.
Turn ON the power switch in the front cabinet of the main unit.
3)
Turn ON the power switch on the operation panel.
DSPF
RSPF
CAUTION
When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
Document scan section
ON
ON
ON
Click on the first or last page to see other MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man11) service manuals if exist.