DOWNLOAD Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man2) Service Manual ↓ Size: 5.22 MB | Pages: 82 in PDF or view online for FREE

 

 

 

1.  Open a web browser and enter the following URL :- 

 

http://ipaddress/service_login.html   or  http://ipaddress/service_account.html 

 

Example: http://192.168.0.156/service_login.html 

 

Note:  If User Authentication (username & password) is enabled, open the device webpage and  
 

           “login” using the service username and password (as below):- 

 

 

 

2.  Select/Enter the “Service” Username and Password to access the Service Webpage and click Login:- 

Default  

Username:  service 

 

 

 

 

 

 

Password: 

service 

 

 

 

3.  When the service webpage opens, click Update of Firmware:- 

 

 

 

 

 

4.  Click Browse to navigate to the location of the updated firmware file and select Open:- 

 

 

 

5.  Press Execute to start the firmware update. 

 

Note: Once the machine has entered “service download mode”, the update will commence and the  

           progress will be displayed. 

 

 

 

6.  When the firmware upgrade is complete, click Reboot to execute a remote restart of the machine. 

 

 

 

Firmware Upgrade is complete

 

 

In the event of a power failure during a firmware update, the device may fail to “reboot” because of 
corrupted firmware. Using the CN Update procedure described below, this function is used to 
update/recover the firmware by transferring data to the MFP PWB, SCU PWB, PCU PWB, FAX PWB, and 
various options by means of a USB memory. 
 
MENU KEY REFERENCE: 

 

The following five keys are used to perform firmware recovery mode. For MX-3050-6070N series, touch the 
LCD panel within the area shown below to select the desired key:- 

 

 

 

 

 

 

    

     [UP]                                 [BACK] 

 

 
 

 

 

 

 

              

 [DOWN]   

 

         [OK] 

     [MENU] 

 

CN UPDATE - Firmware Recovery Procedure:- 
 

1.  Power off the MFP and remove the MFP Rear Cabinet & Screws. 

 

2.  Set the SCN-MFP CONTROL PWB UPDATE DIP-SW to ON:- 

 

 

Note: If a Boot failure has occurred, replace the Boot FlashROM. 

 

3.  Install the USB Memory containing the MX-3060/3070/3560/3570/4060/4070/5070/6070N firmware 

into the USB slot. 

Note: The Firmware file (*.sfu) must only be saved on the main or one level lower directory of the 
           USB Memory. 

 

4.  Power ON the MFP device - the UPDATE PROGRAM INIT PLEASE WAIT boot menu should appear  

after approx 10 seconds, followed by VERSION CHECK CONFIG: information:-. 

 
 
 

 

 

Version Check 
  Conf: 00050000 

Update Program Init 
Please wait

 

 

 

5.  Select FIRM UPDATE Mode by using the [Menu] & [Back] keys. Using the [UP] and [DOWN] keys, 

navigate and select the required firmware SFU. 

 
 
 

 

Note: 
Use the [OK] key when a directory name is selected to browse through to the sub folder(s) or  
the [BACK] key to return to the parent folder(s). 
 

6.  Press [OK] to commence Firmware Update. – It may take approx. 1-2 minutes to read the SFU file. 

After reading is completed, the firmware update (writing) will commence automatically. 

 
 
 
 

Note:   
The abbreviated name/location of the firmware that is being updated will appear in the upper  
right corner. 

 

7.  If the firmware upgrade completes successfully, RESULT OK will be displayed:- 

 
 
 
 

Result: NG = Update failed;    Result: Not Update = Update is not executed. 

 

8.  Power off the MFP and return the SCN-MFP CONTROL PWB UPDATE DIP-SW to OFF (Default):- 

 

 

 

9.  Power ON the MFP, and confirm that the machine boots up normally. 

 

10. Power OFF the MFP and refit the MFP PWB Rear Cabinet & Screws. 

 

11. Check/confirm the firmware version using SIM 22-05. 

 

CN UPDATE - Firmware Recovery Procedure is now complete. 

 

 
 

Firm Update 
> 0300Z100.sfu

 

Firm Update 
    Reading Data

 

Firm Update              IcuM 
    Writing Data

 

Firm Update           IcuM 
    Result  :  OK

 

Firm Update 
    From USB Memory