Sharp DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man5) Service Manual ▷ View online
DX-C401 SIMULATION 5 – 10
63
1
Used to display the shading correction result.
Scanner
2
Used to perform shading.
3
Used to perform scanner (CCD) color balance and gamma auto adjustment.
Scanner
4
Used to display the SIT chart patch density.
5
Used to perform the scanner (CCD) color balance and gamma default setting.
6
Used to display the scan level and the density level of the copy color balance adjustment patch.
7
Used to register the service target of the copy mode auto color balance adjustment.
8
Used to set the default of the service target of the copy mode auto color balance adjustment.
11
Used to set the target color balance of the copy mode auto color balance adjustment.
64
1
Test print. (Self print) (Color mode)
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print) (256 gradations)
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
7
Used to print the adjustment pattern of the test print. (Self print).
(The adjustment pattern of SIM46-21 is printed.)
(The adjustment pattern of SIM46-21 is printed.)
65
1
Used to adjust the touch panel (LCD display section) detection coordinates. (8.5 Inch LCD model only)
Operation panel section
2
Used to display the touch panel (LCD display section) detection coordinates. (8.5 Inch LCD model only)
5
Used to check the operation panel key input.
67
17
Used to reset the printer controller.
Printer
24
Printer color balance adjustment (Auto adjustment)
Printer
25
Printer color balance adjustment (Manual adjustment)
Printer
26
Used to set the target color balance of the printer mode auto color balance adjustment.
Printer
27
Used to set the service target of the printer mode auto color balance adjustment.
Printer
28
Used to set the default of the service target of the printer mode auto color balance adjustment.
Printer
31
Used to clear the printer calibration value.
Printer
33
Used to change the gamma of the printer screen. (for PCL/PS)
Printer
34
Used to set the density correction in the printer high density section. (Support for the high density section
tone gap)
tone gap)
Printer
36
Used to adjust the density in the low density section.
Printer
52
Used to reset the printer color balance adjustment (adjustment for each dither) to the default value. (The set
values of SIM67-54 and SIM67-33 are set to the default values.)
values of SIM67-54 and SIM67-33 are set to the default values.)
54
Printer color balance adjustment (Automatic adjustment for each dither)
70
MFP PWB SRAM data clear
MFP PWB
Main
Sub
Functions
Section
DX-C401 SIMULATION 5 – 11
3. Details of simulation
1
1-1
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the scanner
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
1)
Select the operation speed.
2)
Press [EXECUTE] key.
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
Scanning is once performed at the speed corresponding to the
scan resolution (operation speed).
• 4.3 Inch LCD model
• 8.5 Inch LCD model
1-2
Purpose
Operation test/check
Function (Purpose) Used to check the sensors in the scanner
(reading) section and the related circuits.
Section
Scanner (reading)
Operation/Procedure
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
The operating status of the sensor is displayed.
When "MHPS" is highlighted, the scanner unit is in the home posi-
tion.
• 4.3 Inch LCD model
• 8.5 Inch LCD model
1-5
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the scanner
(reading) unit and the control circuit.
Section
Scanner (reading)
Operation/Procedure
1)
1)
Select the operation speed.
2)
Press [EXECUTE] key.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
Scanning is repeated at the speed corresponding to the scan
resolution (operation speed).
When [EXECUTE] key is pressed, the operation is terminated.
• 4.3 Inch LCD model
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI
(205.9mm/s)
(205.9mm/s)
300DPI
(205.9mm/s)
(205.9mm/s)
400DPI
400DPI
(154.4mm/s)
(154.4mm/s)
600DPI
600DPI
(102.9mm/s)
(102.9mm/s)
1200DPI
1200DPI
(51.5mm/s)
(51.5mm/s)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
6&$11(5&+(&.
7(67
'3,
'3,
'3,
'3,
2&6&$1
(;(&87(
Item/Display
Operation mode
Default value
OC SCAN
300DPI
300DPI
(205.9mm/s)
(205.9mm/s)
300DPI
(205.9mm/s)
(205.9mm/s)
400DPI
400DPI
(154.4mm/s)
(154.4mm/s)
600DPI
600DPI
(102.9mm/s)
(102.9mm/s)
1200DPI
1200DPI
(51.5mm/s)
(51.5mm/s)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
6&$11(56(1625&+(&.
7(67
0+36
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
6&$11(5&+(&.
7(67
'3,
'3,
'3,
'3,
2&6&$1
(;(&87(
DX-C401 SIMULATION 5 – 12
• 8.5 Inch LCD model
2
2-1
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the auto
document feed unit and the control circuit.
Section
RSPF
Operation/Procedure
1)
1)
Select the operation mode and the speed.
2)
Press [EXECUTE] key.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
The RSPF repeats paper feed, transport, and paper exit oper-
ations at the speed corresponding to the scan resolution (oper-
ation speed).
When [EXECUTE] key is pressed, the operation is terminated.
• 4.3 Inch LCD model
• 8.5 Inch LCD model
2-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in the document
feed unit section and the control circuits.
feed unit section and the control circuits.
Section
RSPF
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
• 4.3 Inch LCD model
• 8.5 Inch LCD model
Item/Display
Operation mode
Default value
(SINGLE)
300DPI
300DPI
(205.9mm/s)
(205.9mm/s)
300DPI
(205.9mm/s)
(205.9mm/s)
400DPI
400DPI
(154.4mm/s)
(154.4mm/s)
600DPI
600DPI
(102.9mm/s)
(102.9mm/s)
(DOUBLE)
300DPI
300DPI
(205.9mm/s)
(205.9mm/s)
300DPI
(205.9mm/s)
(205.9mm/s)
400DPI
400DPI
(154.4mm/s)
(154.4mm/s)
600DPI
600DPI
(102.9mm/s)
(102.9mm/s)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
63)$*,1*
7(67
'3,
'3,
'3,
63)6&$1
(;(&87(
6,1*/(
'28%/(
SSET
RSPF installation detection
SOCD
RSPF open/close detector
SCOV
RSPF cover open/close detector
SPED
RSPF document empty detector
SPPD1
RSPF transport detector 1
SPPD2
RSPF transport detector 2
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
63)6(1625&+(&.
7(67
66(7
62&'
6&29
63('
633'
633'
DX-C401 SIMULATION 5 – 13
2-3
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the loads
in the auto document feed unit and the con-
trol circuit.
trol circuit.
Section
RSPF
Operation/Procedure
1)
1)
Select a target item of the operation check.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
• 4.3 Inch LCD model
• 8.5 Inch LCD model
3
3-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and the detectors in the finisher and
the control circuit.
the control circuit.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
The code names of the sensors and the detectors which are active
are highlighted.
• 4.3 Inch LCD model
• 8.5 Inch LCD model
3-3
Purpose
Operation test/check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1)
1)
Select the item to be operation checked.
2)
Press [EXECUTE] key.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
The selected load performs the operation.
When [EXECUTE] key is pressed, the operation is terminated.
SPFM_F
RSPF transport motor (normal rotation)
SPFM_R
RSPF transport motor (reverse rotation)
SPUS
RSPF paper feed roller solenoid
FPPD1
Finisher paper pass detector
FPLD
Finisher paper level detector
FDTULS
Finisher delivery tray upper limit sensor
FDTLLS
Finisher delivery tray lower limit sensor
FDRPS
Finisher delivery roller position sensor
FPRD-F
Finisher paper rear edge detector F
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
63)287387&+(&.
7(67
6350B)
6386
6350B5
(;(&87(
FPRD-C
Finisher paper rear edge detector C
FPRD-R
Finisher paper rear edge detector R
FAPHPS-F
Finisher paper alignment plate home position sensor F
FAPHPS-R
Finisher paper alignment plate home position sensor R
FSTPD
Finisher staple tray paper detector
FSHPS
Finisher staple home position sensor
FSED
Finisher staple empty detector
FSLD
Finisher staple lead detector
FSSW
Finisher safety swithch
FPGS
Finisher paper gate solenoid
FPDM
Finisher paper delivery motor
FPS
Finisher paddle solenoid
FARLS
Finisher alignment roller lift solenoid
FPTM
Finisher paper transport motor
FDRLM
Finisher delivery roller lift motor
FPAM-F
Finisher paper alignment motor F
FPAM-R
Finisher paper alignment motor R
FSM
Finisher staple motor
FTLM
Finisher tray lift motor
FSCF
Finisher stapler cooling fan
FBCF
Finisher control board cooling fan
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
),16(1625&+(&.
7(67
)33'
)3/'
)'78/6
)'7//6
)'536
)35')
)35'&
)35'5
)$3+36)
)$3+365
)673'
)6+36
)6('
)6/'
)66:
Click on the first or last page to see other DX-C310 / DX-C311 / DX-C400 / DX-C401 (serv.man5) service manuals if exist.