DOWNLOAD Sharp AR-FX8 Service Manual ↓ Size: 2.14 MB | Pages: 74 in PDF or view online for FREE

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 1

Enter the copy mode and perform the following procedures.

[P]  

[*]  

[C]  

[*]  

[Main 

code]  

[START]  

[Sub 

code]  

[START]

Enter the copy mode and perform the following procedures.

[9]  

[*]  

[8]  

[#]  

[7]

Press [USER SETTING] to return to the code entry screen. 

Press CA key to cancel the simulation mode.

Code

Function (Content)

Purpose

Section

Item

Main Sub

22

5

Used to check the ROM version of each unit (section).

Other

Software

6

Used to print the list of adjustments and setup data (simulations, 
FAX soft switches, counters).

Adjustment, setup, 
operation data output, 
check (print)

Data

Setup, 
adjustment 
data

11

Used to check the use frequency of FAX. (send/receive)
(Only when FAX is installed.)

Adjustment, setup, 
operation data output, 
check (display)

FAX

Data

23

2

Jam/Trouble data print

24

10

Used to clear the FAX counter. (After completion of maintenance, 
this counter must be cleared.) (Only when FAX is installed.)

Data clear

FAX

Counter

46

12

Used to adjust the print density in the FAX mode (all modes). 
An adjustment with this simulation affects all the copy density 
adjustment values. (Only when FAX is installed)

Adjustment

Picture 
quality

13

Used to adjust the print density in the FAX mode (Standard mode). 
(Only when FAX is installed.)

Adjustment

Picture 
quality

14

Used to adjust the print density in the FAX mode (Fine mode). 
(Only when FAX is installed.)

Adjustment

Picture 
quality

15

Used to adjust the print density in the FAX mode 
(Super Fine mode). (Only when FAX is installed.)

Adjustment

Picture 
quality

16

Used to adjust the print density in the FAX mode (Ultra Fine mode). 
(Only when FAX is installed.)

Adjustment

Picture 
quality

56

1

Data transfer

61

3

Used to adjust  laser power (absolute value) in the FAX reception 
mode. (Only when FAX is installed.)

Adjustment

Operation

66

1

Used to set the FAX soft switch function. (Used to utilize the FAX 
soft switch function.)

Setup

FAX

2

Used to set the FAX soft switch setup to the default. 
(Except for the adjustment values) 

Data clear

FAX

Data

3

Used to check the operations of FAX PWB memory (read/write). 
(This adjustment is required when replacing the PWB with a new 
one.)

Operation test, check

FAX

Data

4

Used to check the operations of data signal output in the FAX data 
output mode. (Used to check the MODEM operation.)
Send level Max. (Only when FAX is installed.)

Operation test, check

FAX

Operation

5

Used to check the operations of data signal output in the FAX data 
output mode. (Used to check the MODEM operation.) 
Signals are sent in the send level set with the soft switch. 
(Only when FAX is installed.)

Operation test, check

FAX

Operation

6

Used to print the confidential password. 
(Used when the confidential password is forgotten.)
(Only when FAX is installed.)

User data output, check 
(display, print)

FAX

Data

7

Used to print the image memory data (memory send, receive). 
(Only when FAX is installed.)

User data output, check 
(display, print)

FAX

Data

8

Used to check the output operation of the FAX sound signals. 
(Sound output IC operation check) Send level Max. 
(Only when FAX is installed.)

Operation test, check

FAX

Operation

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 2

66

9

Used to check the output operation of the FAX sound signals. 
(Sound output IC operation check) (Only when FAX is installed.)

Operation test, check

FAX

Operation

10

Used to clear all data of image memory 
(memory send, receive). Confidential data are also cleared. 
(Only when FAX is installed.)

User data output, check 
(display, print)

FAX

Data

11

Used to check the output operation of FAX G3 mode 300BPS. 
(Used to check the MODEM operation.) Send level 0dB (Max.) 
(Only when FAX is installed.)

Operation test, check

FAX

Operation

12

Used to check the output operation of FAX G3 mode 300BPS. 
(Used to check the MODEM operation.)  Signals are sent in the 
send level set with the soft switch. (Only when FAX is installed.)

Operation test, check

FAX

Operation

13

Used to enter (set) the number for the FAX dial signal output test. 
(The dial number signal set with this simulation is outputted in the 
dial signal output test with SIM 66-14 – 16)
(Only when FAX is installed.)

Setup

FAX

Data

14

Used to set the make time in the FAX pulse dial mode (10PPS) and 
to test the dial signal output. 
(The dial number signal set with SIM 66-13 is outputted.) 
Used to check dialing troubles and the operation. 
(Only when FAX is installed.)

Setup

FAX

Operation

15

Used to set the make time in the FAX pulse dial mode (20PPS) and 
to test the dial signal output. (The dial number signal set with SIM 
66-13 is outputted.) Used to check dialing troubles and the 
operation. (Only when FAX is installed.)

Setup

FAX

Operation

16

Used to test the dial signal (DTMF) output in the FAX tone dial 
mode. (The dial number signal set with SIM 66-13 is outputted.) 
The send level can be set to an optional level. 
Dialing troubles and operation. (Only when FAX is installed.)

Setup

FAX

Operation

17

Used to test the dial signal (DTMF) output in the Fax tone dial 
mode. Send level Max. Used to check the operation. 
(Only when FAX is installed.)

Setup

FAX

Operation

18

Used to test the dial signal (DTMF) in the FAX tone dial mode. The 
send level set with the soft switch is outputted. Used to check the 
operation. (Only when FAX is installed.)

Setup

FAX

Operation

19

Used to backup the Address data into the flash Memory
(Option FAX memory:AR-MM9) (Only when FAX is installed.)

Setup

FAX

Operation

20

Used to restore the backup data (SIM 66-19) to Address data.
(Only when FAX is installed.)

Setup

FAX

Operation

21

Used to print the FAX information (registrations, communication 
management, file management, system errors, protocol).
(Only when FAX is installed.)

Adjustment, setup, 
operation data output, 
check (display, print)

FAX

Data

23

Used to download the FAX program. (Only when FAX is installed.)

Inhibited

FAX

24

Used clear the FAST memory data. (Only when FAX is installed.)

Inhibited

FAX

25

Used to register the FAX number for MODEM dial-in. 
(Only when FAX is installed.)

Inhibited

FAX

26

Used to register the external telephone number for MODEM dial-in. 
(Only when FAX is installed.)

Inhibited

FAX

27

Used to register the voice-warp transfer number. 
(Only when FAX is installed.) (Voice-warp: Japan only)

Inhibited

FAX

29

Used to clear the Address data.

Setup

FAX

Operation

30

Used to check TEL/LIU status change.

Setup

FAX

Operation

31

Used to set the TEL/LIU status.

Setup

FAX

Operation

32

Used to check received data.

Inhibited

FAX

33

Used to check signal detection.

Inhibited

FAX

34

Used to measure and display the communication time.

Setup

FAX

Operation

35

Modem program rewriting.(Only when FAX is installed.)

Operation test, check

FAX

Operation

36

Used to check I/F between MFPC and MDMC. 
Check is made in the data line or the command line.

Operation test, check

FAX

Operation

39

Registration of FAX destination

FAX

Code

Function (Content)

Purpose

Section

Item

Main Sub

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 3

Purpose

Other

Function 
(Content)

Used to check the ROM version of each unit (section).

Section
Item

Software

Operation/
Procedure

The version of each ROM is displayed.

S/N

Engine section serial number

MFP

MFP controller

(LANGUAGE)

(Language version)

BOOT

MFP controller boot ROM

FAX

FAX controller

PCU

PCU controller

SCANNER

Scanner controller

FINISHER

Finisher controller

SADDLE UNIT

Saddle unit

LCC

Side LCC

INSERTER

Inserter

Purpose

Adjustment, setup, operation data output, check (print)

Function 
(Content)

Used to print the list of adjustments and setup data 
(simulations, FAX soft switches, counters).

Section

Item

Data

Operation/
Procedure

The selected data is displayed on the right side of the 
item.

0

TRAY SELECT auto only (no selection)

1

PRINT  START 

SIMULATION 22-5
ROM VERSION DATA DISPLAY.
S/N   :              000000000
MFP :                              1.00          (LANGUAGE :  1.00)
PCU :                              1.00                             BOOT :                 1.00
SCANNER :                    1.00                                FAX :                 1.00
FINISHER :                     1.00                               
SADDLE UNIT :              1.00                                LCC :                 1.00
INSERTER :                    1.00

SIMULATION 22-6
DATA PRINT MODE, SELECT SETTING,AND PRESS START.
0. TRAY SELECT

:AUTO ONLY

1. PRINT START

1

SIMULATION 22-6
DATA PRINT MODE.. EXECUTING...
0.TRAY SELECT

: 

0

1

When "1" is selected, 
press [START]  key.

Press  [CUSTOM SETTINGS] key

or  [START] key

Purpose

Adjustment, setup, operation data output, check (display)

Function 
(Content)

Used to check the use frequency of FAX. (send/receive) 
(Only when FAX is installed.)

Section

FAX

Item

Data

Operation/
Procedure

The counter data below are displayed.

FAX SEND

Number of times of FAX sending

FAX RECEIVE

Number of times of FAX receiving

FAX OUTPUT

FAX print quantity

SEND IMAGES

Quantity of sending

SEND TIME

Time for sending

RECEIVE TIME

Time for receiving

Purpose

Function 
(Content)

Jam/Trouble data print

Section

Item
Operation/
Procedure

The current selected data is displayed on the side of the 
menu.

0

TRAY SELECT (Selection disabled)

1

PRINT START

SIMULATION 22-11
FAX COUNTER DATA DISPLAY.
FAX SEND :  ********       FAX RECEIVE :  ********
FAX OUTPUT :  ********
SEND IMAGES :  ********       SEND TIME :  ********:**:**
RECEIVE TIME :  ********:**:**

SIMULATION 23-2
JAM/TOROUBLE DATA PRINT MODE. SELECT SETTING, AND
PRESS START.
0. TRAY SELECT

:AUTO ONLY

1. PRINT START

1

When "1" is selected,
press  [START] key

SIMULATION 23-2
JAM/TOROUBLE DATA PRINT MODE.. EXECUTING .
0.TRAY SELECT

: 

0

1

Press  [CUSTOM SETTINGS] key

or  [START] key

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 4

Purpose

Data clear

Function 
(Content)

Used to clear the FAX counter.

Section

FAX

Item

Counter

Operation/
Procedure

Select with 10 digit key pad and press START key.
The procedure below is executed and the display returns 
to the original state.
1: Counter is cleared  2: Not cleared

1

FAX SEND: Number of times of FAX sending

2

FAX RECEIVE: Number of times of FAX reception

3

FAX OUTPUT: FAX print quantity

4

SEND IMAGES: Sending quantity

5

SEND TIME: Time for sending

6

RECEIVE TIME: Time for reception

Purpose

Adjustment

Function 
(Content)

Used to adjust the print density in the FAX mode (all 
modes). An adjustment with this simulation affects all the 
reading density adjustment values.
(Only when FAX is installed)

Section
Item

Picture quality

Operation/
Procedure

The exposure mode to be set is selected. 
(FAX auto adjustment)
1) The current set value is highlighted on the right side

of each item. In this screen, be sure to select "1:
COPY START." (Set value: 1)

2) Set the exposure level with 10 digit key pad. 

Press P to store the set value. 
(Default: 50, set range: 0 - 99)

3) Press START, and copying is started and the set

value is stored. (Display value 1)

4) Select a paper feed tray. (Set value 2)

1

SIMULATION 24-10
* COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO

1

SIMULATION 24-10
FAX COUNTER DATA CLEAR. SELECT 1-6, AND PRESS START.
1. FAX SEND
2. FAX RECEIVED
3. FAX OUTPUT
4. SEND IMAGES
5. SEND TIME
6. RECEIVE TIME

Press [START] key.  

Press  [CUSTOM SETTINGS] key

or  [START] key

0

Paper feed tray selection

1

Copy start (Default)

2

FAX mode exposure setup

Normal display

“NOW PRINTING”

ERROR display

DOOR OPEN.
JAM

PAPER EMPTY.

1

TRAY1

2

TRAY2

3

TRAY3

4

TRAY4

5

Manual feed

6

Side LCC

SIMULATION 46-12
EXP. LEVEL SETUP FAX (AUTO SET). SELECT 0-2, AND PRESS START.
0. TRAY SELECT              1. COPY START
2. FAX EXP. LEVEL

1

SIMULATION 46-12
EXP. LEVEL SETUP FAX (AUTO SET),INPUT VALUE 0-99, AND PRESS
 START.
2. FAX EXP. LEVEL

50

SIMULATION 46-12
EXP.  LEVEL SETUP FAX (AUTO SET). SELECT 1-6, AND PRESS START. 
(FEED TRAY)
1. TRAY1  2. TRAY2  3. TRAY3  4. TRAY4  5.BPT  6.LCC

1

SIMULATION 46-12
EXP. LEVEL SETUP FAX (AUTO SET). NOW PRINTING.

1

50

Select other than 0 - 1, 
and press [START] key.  

Select 1, and 
press [START] key.  

Select 0, and 
press [START] key.  

Press [START] key.  

Press  [CUSTOM SETTINGS] key

Press  [CUSTOM SETTINGS] key

Press  [CUSTOM SETTINGS] key

Or copying is terminated.

Press  [START] key or