Sharp AR-FX8 Service Manual ▷ View online
AR-FX8 SIMULATIONS, FAX SOFTWARE SWITCH 6 - 21
TEL/FAX auto
switch
switch
TEL/FAX auto switch setup
Initial setup
SW 7-1
The line is used either for TEL or FAX.
Voice response send level to the line
SW 51-1
Voice response send in TEL/FAX auto switch
SW 51-2~3
Number of ring back tone preceding send
SW 9-5~8
External
telephone call
telephone call
Number of calls by external telephone
pseudo-ringing sound
pseudo-ringing sound
Initial setup
SW 9-1~4
Ring back tone ON time
SW 10-1~4
External telephone call disable
CNG detection disable
CNG detection disable
Ring back tone OFF time
SW 10-5~8
External telephone call disable
CNG detection disable
CNG detection disable
Communication General
Signal send level
SW 15-1~8
When the remote machine does not
receive signals in a proper level.
receive signals in a proper level.
Polarity reversion monitor in communication
SW 23-2
When the line is disconnected during
communication, the communication
report code 2 of 11 or 20 is resulted.
communication, the communication
report code 2 of 11 or 20 is resulted.
ECM (Other than V.34 mode)
Initial setup
SW 17-5
Error resend frequently occurs, resulting
in extended communication time.
in extended communication time.
Timer setup between flag-adrs (V.21-FSK)
SW 20-3~4
Communication error in a satellite line
Send/receive coding capacity (Only V.34)
SW 17-3~4
Error in JBIG mode
Send/receive coding capacity
(Except for V.34)
(Except for V.34)
SW 17-7~8
Error in JBIG mode
SG3
V.34 mode function
SW 43-1
Frequent errors in SG3 communication
V.34 Symbol Rate Mask
SW 43-3~6
Frequent errors in SG3 communication
V.34 mode function in manual
communication
communication
SW 42-8
Frequent errors in SG3 communication
in FAX service
in FAX service
Send
G3/SG3
Countermeasures against echo in sending
SW 20-7
An error occurs in phase B.
DIS reception confirmation
SW 20-2
An error occurs in phase B.
CED detection time
SW 25-5
CED signal detection error
SG3
V.34 mode send speed
SW 44-1~4
An error occurs in SG3 communication.
G3
Echo suppresser tone
SW 27-1~4
An error occurs in V.29 communication
Modem send speed
SW 16-1~4
To uncertain/certain receiver
DCS-TCF interval time
SW 24-1
An error occurs in training.
Error process in RTN reception
SW 30-2
OK is displayed when RTN is received.
Receive
G3/SG3
CSI send
SW 20-1
SG3
V.34 mode reception speed
SW 44-5~8
An error occurs in SG3 communication.
G3
Countermeasures against echo in reception
SW 20-6
An error occurs n phase B in reception.
Modem speed fixed in reception
SW 16-5~6
Fall back or an error occurs due to poor
line conditions.
line conditions.
EOL detection timer
SW 23-1
EOL time up occurs frequently.
RTN send line error rate
SW 23-7~8
Line error occurs frequently.
EQM judgment in TCF reception
confirmation
confirmation
SW 24-2
TCF reception error occurs.
TCF reception confirmation judgment
method
method
SW 24-3
TCF reception error occurs.
Receive print
Paper
selection
selection
Sub scan length judgment
SW 35-2
Print is not made on the selected paper.
FAX paper exit tray
Receive
setup
setup
SW 28-7~8
Print is not made on the selected paper.
Reception data print output condition setup
Receive
setup
setup
SW 35-3~4
To make divided print instead of
reduction print.
reduction print.
Auto reduction/Dispose setup
Receive
setup
setup
SW 35-7
To disable reduction print.
magnification ratio setup in auto reduction
SW 36-1~8
To disable reduction print on fixed size
paper.
paper.
Reduction/Dispose setup in printing
A3-11x17
A3-11x17
SW 35-8
Print is not made on the selected paper
when A3-11x17 size document is
received.
when A3-11x17 size document is
received.
Duplex reception print
Receive
setup
setup
SW 34-8
To make duplex print of received
document
document
Rotation print
SW 35-1
To disable rotation print
Received document output setup in
reception
reception
SW 35-5
To print after reception of each page
Reception width setup of 11 x 17 paper
SW 37-3
To print 11x17 document as B4 width
Reception size setup
SW 37-1~2
To limit the reception size.
Large item
Medium item
Content of switch
Key operator Soft SW No.
Purpose of use
AR-FX8 SIMULATIONS, FAX SOFTWARE SWITCH 6 - 22
B. Details
US = U.S.A./Canada,
UK = U.K.,
FR = France,
GR = Germany,
SW = Sweden,
AS = Australia,
NZ = New Zealand
SW
No.
No.
Bit
No.
Item
Switch selection and function
US UK FR GR SW AS NZ Initial value
Key
operator
1
1-8 Country code
Country code set by ITU-T. Control is made according to
the set country code.
the set country code.
1
1
0
0
1
0
0
0
0
0
0
0
0
1
1
1
1
0
1
0
1
1
1
1
0
0
0
1
0
0
1
0
0
1
1
1
1
1
1
1
0
1
0
0
0
0
0
0
1
1
0
1
0
1
1
0
2
1
TSI judgment setting
when a certain number
receive reject
(No signal or all space)
when a certain number
receive reject
(No signal or all space)
Used to set receive reject or receive allow when there is
no TSI signal from the remote machine or when the TSI
signal is all space, when a certain number receive reject
is set to valid by the key operation.
no TSI signal from the remote machine or when the TSI
signal is all space, when a certain number receive reject
is set to valid by the key operation.
0
0
0
0
0
0
0 Receive
allow
2
Specified number
receive rejection setup
(FAX)
receive rejection setup
(FAX)
Used to set whether a certain number receive reject by
FAX is Enabled or Disabled. In auto receive only.
FAX is Enabled or Disabled. In auto receive only.
0
0
0
0
0
0
0 Specified
number
receive
ignored
(Invalid)
receive
ignored
(Invalid)
Receive
setup
setup
3
Manual receive mode
receive rejection setup
(FAX)
receive rejection setup
(FAX)
Used to set whether a certain number receive reject by
FAX is Enabled or Disabled. In manual receive only.
FAX is Enabled or Disabled. In manual receive only.
0
0
0
0
0
0
0 Specified
number
ignored
ignored
4
Manual receive mode
auto receive switch
setup
auto receive switch
setup
Used to set whether auto receive switch is performed or
not in the manual receive mode. The number of
switching to auto receive is set with SW2-5-8.
not in the manual receive mode. The number of
switching to auto receive is set with SW2-5-8.
0
0
0
0
0
0
0 Inhibit
Receive
setup
setup
5-8 Number of calls to
switch to auto receive in
manual receive
manual receive
Used to set the number of calls to switch to auto receive
in manual receive mode.
This function is valid only when SW2-4 is set to "1: Allow
(to switch)." If a value outside the set range is inputted,
the default setup is made.
in manual receive mode.
This function is valid only when SW2-4 is set to "1: Allow
(to switch)." If a value outside the set range is inputted,
the default setup is made.
1
1
1
1
1
1
1 9 (FR)
Receive
setup
setup
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
3
1
Not used
0
0
0
0
0
0
0
2
External telephone
connection
connection
Setting to use an external telephone. If not set to YES,
an external telephone cannot be used.
an external telephone cannot be used.
In North America, users cannot set this switch to "0: NO."
1
1
1
1
1
1
1 YES
Initial setup
3
Default finish stamp
Used to set whether the finish stamp is used or not after
completion of document scan when the SPF/RSPF is
used.
completion of document scan when the SPF/RSPF is
used.
If a document feed unit other than the SPF/RSPF is
used, this setup is invalid.
used, this setup is invalid.
0
0
0
0
0
0
0 NO
Operation
setup
setup
4
Not used
0
0
0
0
0
0
0
5-8 Number of calls for auto
receives
Used to set the number of calls to start auto receive (to
catch the line). Setup is made in the range of 0 ~ 15 by
binary input.
When set to 0, no ringing is made. For the nighttime FAX
mode (main SW OFF, memory SW ON), however,
ringing of an external telephone is made.
catch the line). Setup is made in the range of 0 ~ 15 by
binary input.
When set to 0, no ringing is made. For the nighttime FAX
mode (main SW OFF, memory SW ON), however,
ringing of an external telephone is made.
0
0
0
0
0
0
0 2
Receive
setup
setup
0
0
0
0
0
0
0
1
1
1
1
1
1
1
0
0
0
0
0
0
0
4
1,2 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
3
Polling protection
Used to set Enable/Disable of confidential protection
(inhibition of transmission to erroneous party) in
transmission of bulletin board. Confidential protection is
made by collating the number registered in this machine
and that in the other party machine. Sender's number
and send request allow number are collated each other.
In this machine, Sharp's unique collating of system
number
(inhibition of transmission to erroneous party) in
transmission of bulletin board. Confidential protection is
made by collating the number registered in this machine
and that in the other party machine. Sender's number
and send request allow number are collated each other.
In this machine, Sharp's unique collating of system
number
ID number is not performed.
0
0
0
0
0
0
0 Protect
Polling
security
setup
security
setup
1: Receive reject
0: Receive allow
1: Specified number
receive rejection (Valid)
receive rejection (Valid)
0: Specified number
receive ignored (Invalid)
receive ignored (Invalid)
1: Specified number
receive rejection
receive rejection
0: Specified number
receive ignored(OFF)
receive ignored(OFF)
1: Allow(Switched)
0: Inhibit (Not switched)
1: External telephone YES 0: External Telephone NO
1: Finish stamp used
0: Finish stamp not used
1: Not protected
0: Protected
AR-FX8 SIMULATIONS, FAX SOFTWARE SWITCH 6 - 23
US = U.S.A./Canada,
UK = U.K.,
FR = France,
GR = Germany,
SW = Sweden,
AS = Australia,
NZ = New Zealand
4
4
Relay data output
Used to set whether the document received from the
relay station is outputted or not when relay broadcast
reception is made.
relay station is outputted or not when relay broadcast
reception is made.
Similar to F code relay broadcast indicating reception.
0
0
0
0
0
0
0 Output
5
Not used
0
0
0
0
0
0
0
6
F code relay broadcast
function
function
Used to set whether relay broadcast transmission is
made by receiving F code relay broadcast instruction
from the other party or F code relay broadcast instruction
is not received (even though the relay box number by
SUB is matched on). Though this item is set to "without
this function," F code relay broad cast instruction can be
transmitted.
made by receiving F code relay broadcast instruction
from the other party or F code relay broadcast instruction
is not received (even though the relay box number by
SUB is matched on). Though this item is set to "without
this function," F code relay broad cast instruction can be
transmitted.
0
0
0
0
0
0
0 Receive
7
F code confidential
reception
reception
Used to set YES/NO of F code confidential reception
from the other party (even though the confidential box
number is matched by SUB). Though this item is set to
NO, F code confidential transmission can be made.
from the other party (even though the confidential box
number is matched by SUB). Though this item is set to
NO, F code confidential transmission can be made.
0
0
0
0
0
0
0 Receive
8
F code communication
error process
error process
Used to set YES/NO of resend in F code transmission.
When, however, SW59-3 (Recall allow in communication
error) is set to 0 (Inhibit), recall is not made.
When, however, SW59-3 (Recall allow in communication
error) is set to 0 (Inhibit), recall is not made.
0
0
0
0
0
0
0 Resend
5
1
F code password
transmission setup
when the other party
has no function of
password
transmission setup
when the other party
has no function of
password
Used when the other party machine has no function of F
code password in F code transmission.
code password in F code transmission.
0
0
0
0
0
0
0 Line dis-
connection
with DCN
with DCN
2,3 Image quality in
reception
(Reflected on DIS, not
reflected on DTC)
(Reflected on DIS, not
reflected on DTC)
Used to set reception image resolution in FAX reception
ringing (DIS send).
ringing (DIS send).
0
0
0
0
0
0
0 Ultra fine
0
0
0
0
0
0
0
4-8 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
6
1
SUB capacity in
reception
reception
Used to set SUB capacity (Bit 49) to "1" in reception (DIS
send).
send).
0
0
0
0
0
0
0 YES
2
SEP capacity in
reception
reception
Used to set SEP capacity (Bit 47) to "1" in reception (DIS
send)
send)
0
0
0
0
0
0
0 YES
3
Reception PWD/SID
capacity
capacity
Used to set PWD/SID capacity (Bit 50) to "1" in reception
(DIS send).
(DIS send).
0
0
0
0
0
0
0 YES
SW
No.
No.
Bit
No.
Item
Switch selection and function
US UK FR GR SW AS NZ Initial value
Key
operator
1: Document received
from relay station is not
outputted.
outputted.
0: Document received
from relay station is
outputted.
outputted.
1: F code relay
broadcast instruction
is received from
allowed party.
is received from
allowed party.
0: F code relay broadcast
instruction is not received
even from allowed party.
(Judged as a
communication error.)
even from allowed party.
(Judged as a
communication error.)
1: F code confidential
reception inhibited (Judged
as a communication error.)
as a communication error.)
0: F code confidential
reception allowed.
1: Not resend
0: Resend
1: Send with password
0: Disconnecting of line
with DCN
Bit No.
2
3
Standard
1
1
Fine + Standard
1
0
Super fine + Fine + Standard
0
1
Ultra fine+ Super fine + Fine +
Standard
Standard
0
0
1: NO (Set to 0)
0: YES (Set to 1)
1: NO (Set to 0)
0: YES (Set to 1)
1: NO (Set to 0)
0: YES (Set to 1)
AR-FX8 SIMULATIONS, FAX SOFTWARE SWITCH 6 - 24
US = U.S.A./Canada,
UK = U.K.,
FR = France,
GR = Germany,
SW = Sweden,
AS = Australia,
NZ = New Zealand
6
4
Automatic reduction
send
send
Used to set whether the transmitted document is
reduced or the both ends are cut when the transmitted
document size is greater than the recording paper size
(width) in the other party's machine.
reduced or the both ends are cut when the transmitted
document size is greater than the recording paper size
(width) in the other party's machine.
0
0
0
0
0
0
0 Reduction
setup
Send setup
5
Rotation send selection
(A4
(A4
A4R)
(LTR
LTR-R)
Used to set whether A4 document is transmitted in A3
width (A4) or A4 document is rotated and transmitted in
A4R.
width (A4) or A4 document is rotated and transmitted in
A4R.
0
0
0
0
0
0
0 Rotate
Send setup
6
Rotation send selection
(B5R
(B5R
B5)
(16K
16KR)
Used to set whether B5R document is transmitted in A4
width (B5R) or the scan image is rotated and transmitted
in B4 width (B5).
width (B5R) or the scan image is rotated and transmitted
in B4 width (B5).
0
0
0
0
0
0
0 Rotate
Send setup
7
Rotation send selection
(A5R
(A5R
A5)
(INVOICE-R
INVOICE)
INVOICE)
Used to set whether A5R document is transmitted to A4
width (A5R) or the scan image is rotated and transmitted
in A4 width (A5).
width (A5R) or the scan image is rotated and transmitted
in A4 width (A5).
0
0
0
0
0
0
0 Rotate
Send setup
8
EEPROM access inhibit When an access trouble to EEPROM in the modem
controller occurs, FAX operation cannot be performed.
When this item is set to INHIBIT, FAX operation can be
performed.
The modem controller adjustment values (part of soft
switch) are saved in EEPROM.
ALLOW or INIHIBIT of access to EEPROM is set.
When this item is set to INHIBIT, FAX operation can be
performed.
The modem controller adjustment values (part of soft
switch) are saved in EEPROM.
ALLOW or INIHIBIT of access to EEPROM is set.
0
0
0
0
0
0
0 Access
allowed
7
1
Not used
0
0
0
0
0
0
0
2
Auto/Manual default
setup
setup
Used to select automatic reception or manual reception.
(Do not set to manual reception when handset or
external telephone is not connected. However, setting is
possible and reception with on-hook key is possible.) In
the manual reception mode, when the machine is in the
nighttime FAX mode, the machine is booted but
reception ringing is not made.
(Do not set to manual reception when handset or
external telephone is not connected. However, setting is
possible and reception with on-hook key is possible.) In
the manual reception mode, when the machine is in the
nighttime FAX mode, the machine is booted but
reception ringing is not made.
0
0
0
0
0
0
0 Auto
reception
User setup
3,4 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5
Remaining memory
capacity for reception
capacity for reception
Used to set whether call-in is made until remaining
memory capacity reaches 64KB or less or 128KB or
less.
memory capacity reaches 64KB or less or 128KB or
less.
0
0
0
0
0
0
0 128KB or
less
6
Memory over during
reception
reception
Used to set whether received data are outputted or
disregarded without outputting in case of memory over
during reception.
disregarded without outputting in case of memory over
during reception.
0
0
0
0
0
0
0 Output
7,8 Not used
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SW
No.
No.
Bit
No.
Item
Switch selection and function
US UK FR GR SW AS NZ Initial value
Key
operator
1: Send by cutting both edges without
reduction
0 Send by
reduction
1: Send as A3 width
document (A4) without
rotating
rotating
0: Send as A4 width
document (A4R) with
rotating
rotating
1: Send as A4 width
document (B5R)
without rotating
without rotating
0: Send as B4 width
document (B5) with
rotating
rotating
1: Send as A4 width
document (A5R)
without rotating
without rotating
0: Send as A4 width
document (A5) with
rotating
rotating
1: Access to EEPROM
inhibited
0: Access to EEPROM
allowed
1: Manual reception
0: Auto reception
1: Call-in until remaining
memory is 64KB or less.
0: Call-in until remaining
memory is 128KB or less.
1: Received data are not
outputted.
0: Received data are
outputted.
Click on the first or last page to see other AR-FX8 service manuals if exist.