DOWNLOAD Sharp AR-FX8 Service Manual ↓ Size: 2.14 MB | Pages: 74 in PDF or view online for FREE

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 17

(This mode is for development, and inhibited in the market.)

Purpose

Setup

Function 
(Content)

Used to restore the backup data (SIM 66-19) to Address 
data. (When FAX is installed and FAX extended memory 
is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

Address data backed up with SIM 66-19 are read from 
the option Flash ROM and written into the machine.
However, data backed up in the Tiger series cannot be 
restored to the machine. If an option Flash ROM backed 
up in the Tiger series is installed, the data in the option 
Flash ROM are deleted.

1

Read/Write executed

2

Read/Write not executed

Purpose

Adjustment, setup, operation data output, check (display, 
print)

Function 
(Content)

Used to print the FAX information (registrations, 
communication management, file management, system 
errors). (Only when FAX is installed.) 

Section

FAX

Item

Data

Operation/
Procedure

Information related to FAX is printed.
1) Enter the number corresponding to the information

(item) to be printed with 10-key.

2) Press [start] key.

1

1

Press [START] key.  

After completion of reading 

SIMULATION 66-20
ADDRESS DATA (READ FROM FLASH ROM)
ARE YOU SURE ?
1. YES
2. NO

SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM)  EXECUTING...

0

SIMULATION 66-21
FAX INFORMATION PRINT OUT.EXECUTING...
1. REGISTERED

SIMULATION 66-21
FAX INFORMATION PRINT OUT. SELECT 1-5, AND PRESS START.
1.REGISTERED

2.MANAGEMENT

3.FILE MANAGEMENT 

4.SYSTEM ERROR

5.PROTOCOL     

Select other than 0 and 
press [START] key. 

If there is no print data, 
the display returns to the
original state without printing.

After completion of printing 

(When 1) 

1

REGISTERED

Various registered information

2

MANAGEMENT

Communication management information

3

FILE 
MANAGEMENT

File management information

4

SYSTEM ERROR System error information

5

PROTOCOL

Protocol information

Purpose

Operation test, check

Function 
(Content)

Used to download the FAX program. 
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

The contents of ROM in the option memory (AR-MM9) 
installing section are copied as FAX program.

Purpose

Operation test, check

Function 
(Content)

Used to clear the FAST memory data.
(Only when FAX is installed.)

Section

FAX

Item

Operation 

Operation/
Procedure

1) Select with 10 digit key pad, press START to execute

the following.

1: Fast memory data clear
2: Not clear

SIMULATION 66-23
FAX PROGRAM DOWNLOAD.
EJECT PROTECT PIN, AND PRESS START.

SIMULATION 66-23
FAX PROGRAM DOWNLOAD. EXECUTING...

SIMULATION 66-23
FAX PROGRAM DOWNLOAD. 
FAIL
CHECK PROTECT PIN

SIMULATION 66-23
FAX PROGRAM DOWNLOAD. 
COMPLETE
POWER OFF, AND SET PROTECT PIN

Press [START] key.  

After normal completion of writing

After failure of writing

SIMULATION 66-24
FAST MEMORY DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 18

(This mode is for production check, and inhibited in the market.)

(This mode is for production check, and inhibited in the market.)

Purpose

Setup

Function 
(Content)

Used to clear the Address data.

Section

FAX, NWS

Item

Operation

Operation/
Procedure

1) Select with 10 digit key pad and press START to

execute the following.

1: 

Address data

 clear

2: 

Address data

 not clear

Purpose

Setup

Function 
(Content)

Used to check TEL/LIU status change. 
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

The TEL/LIU status can be checked.
The display is highlighted when the status is changed.

HS1

Polarity reverse signal

HS2

Polarity reverse signal

RHS

Handset hook SW

EXHS

External telephone hook SW

Purpose

Setup

Function 
(Content)

Used to set the TEL/LIU status. 
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

Entry of only 0 or 1 is effective.
Shift the cursor to the bit to enter.
Cursor shift keys : 

 : * , 

 : #.

The bits are 1, 2, 3, 4, 5, 6, 7, and 8 from the left.
The entered bit is highlighted.
Press STRT to select the relay.

Purpose

Setup

Function 
(Content)

Used to check the received data.
(Only when FAX is installed.)

Section

FAX

Item

Operation

Operation/
Procedure

The fixed data received from the line are checked.

SIMULATION 66-29
ADDRESS DATA CLEAR.
ARE YOU SURE ?
1. YES
2. NO

1

SIMULATION 66-30
TEL/LIU SENSOR CHECK.
HS1       HS2

EXHS

RHS

10001100

SIMULATION 66-31
TEL/LIU SETTING.
INPUT 0 - 1, AND PRESS START.
MOVEMENT LEFT: [*]  RIGHT: [#]
1. 

2.CION 

3. MR

4. EC

5. 6. 7. 

DP

8. 

1  2  3  4  5  6  7  8

MPXA

S.

CML

CHECKING

Checking

OK

Checking complete (Coincided)

NG

Checking end (Not coincided)

Purpose

Setup

Function 
(Content)

Used to check signal detection.

Section

FAX

Item

Operation

Operation/
Procedure

When the signal is detected, the display is highlighted.

Purpose

Setup

Function 
(Content)

Used to measure and display the communication time.

Section

FAX

Item

Operation

Operation/
Procedure

The time spent for communication is measured. 
Send/receives are performed in the Standard mode.
The communication time is displayed with the simulation. 
(unit: ms)

Communication means

memory transmission

Image quality

Normal 

Density

Thin

ECM

ON

Sender record

OFF

Purpose

Operation test, check 

Function 
(Content)

Modem program rewriting.

Section

FAX

Item

Operation

Operation/
Procedure

The modem program in the FAX program is rewritten.
1) Select with 10 digit key pad and press START to

execute the following.

1: MODEM program rewrite
2: Not clear

2) Check the loader check sum value. 

If it is OK, the test is normally completed. 
If NG, the check sum value 
(1 byte = hexadecimal) is displayed.

3) If the loader is NG, the MODEM result is also NG.
4) The Modem rewrite result is displayed.

SIMULATION 66-32
RECEIVED DATA CHECK.
CHECKING...(OK or NG)

SIMULATION 66-33
SIGNAL DETECT CHECK.
BUSY TONE

CNG

CED

FNET

DTMF

SIMULATION 66-34
COMMUNICATION TIME DISPLAY.
***** ms

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 19

COMPLETE

Writing completed

81

Check sum error

82

Write error

83

Delete error

84

Verify error

NG

Due to loader error

Purpose

Operation test, check

Function 
(Content)

Used to check I/F between MFPC and MDMC. 
Check is made in the data line or the command line.

Section

FAX

Item

Operation 

Operation/
Procedure

1) Select with 10 digit key pad and press START.
2) When check is "repeat," the operation is executed

until the result becomes NG or CUSTOM SETTING is
pressed.

1

MFPC <- MDMC

Data line once only

2

MFPC -> MDMC

Data line once only

3

MFPC <- MDMC

Data line repeat

4

MFPC -> MDMC

Data line repeat

5

MFPC <- MDMC

Command line once only

6

MFPC -> MDMC

Command line once only

7

MFPC <- MDMC

Command line repeat

8

MFPC -> MDMC

Command line repeat

SIMULATION 66-35
MODEM PROGRAM RELOAD.
ARE YOU SURE ?
1. YES
2. NO

1

SIMULATION 66-35
MODEM PROGRAM RELOAD. EXECUTING...
LOADER...(OK or  Check Sum value 1 byte (Hexadecimal))
MODEM...(COMPLETE or NG code  1 byte (Hexadecimal))

SIMULATION 66-35
MODEM PROGRAM RELOAD. 
LOADER...OK
MODEM...COMPLETE

Press [START] key.

After completion of writing

SIMULATION 66-36
MFPC-MDMC I/F CHECK . INPUT 1-8, AND PRESS START.
1. MFPC<-MDMC(DATA once)
2. MFPC->MDMC(DATA once)
3. MFPC<-MDMC(DATA repeat)
4. MFPC->MDMC(DATA repeat)
5. MFPC<-MDMC(CMD once)
6. MFPC->MDMC(CMD once)
7. MFPC<-MDMC(CMD repeat)
8. MFPC->MDMC(CMD repeat)

1

1

SIMULATION 66-36
MFPC-MDMC I/F CHECK . INPUT 1-8, AND PRESS START.
EXECUTING...

SIMULATION 66-36
MFPC-MDMC I/F CHECK . INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG)

Press [START] key.

When check is "once" or "repeat"  
and the result is NG 

When check is "repeat" and 
[CUSTOM SETTINGS] key is pressed.

Purpose

Function 
(Content)

Registration of FAX destination

Section

FAX

Item

Operation/
Procedure

The current destination saved in the EEPROM of 
FAXBOX is displayed.
Entries of 1 - 6 only are valid. Enter the number 
corresponding to your desired destination.
(If no destination is saved in the EERPOM of FAXBOX, 
"0" is displayed.)
1) Enter the number with the 10-key and press [START]

key, and the destination will be written on the FAX.

1

Japan

2

North America

3

Europe (including U.K.)

4

Australia

5

China

6

Asia

SIMULATION 66-39
FAX DESTINATION SETUP.
SELECT 1 - 6, AND PRESS START
0. NO DESTINATION
1. JAPAN
2. U.S.A/CANADA
3. EUROPE
4. AUSTRALIA
5. CHINA
6. ASIA

1

press  [START] key

AR-FX8  SIMULATIONS, FAX SOFTWARE SWITCH  6 - 20

Large item

Medium item

Content of switch 

Key operator Soft SW No.

Purpose of use

Dial (Calling)

Remote 
machine 
calling disable

Monitoring polarity reverse in calling

SW 23-3

Dial disable

Line current detection in dial call

SW 70-5

Dial disable

Dial call wait time

SW 62-1~2

Dial disable/Erroneous dialing

Pause time

Initial setup

SW 70-1~4

Dial disable/Erroneous dialing

Tone/Pulse default setup (Dial call signal)

Initial setup

SW 62-5~6

Dial disable

•DTMF signal level (high group)
•DTMF send level (low group)
•DTMF signal send time 
•DTMF minimum pause

SW 66-5~8

Dial disable in PB (PB/FAX service, etc.)

SW 67-1~4

Dial disable in PB (PB/FAX service, etc.)

SW 68-1~5

Dial disable in PB (PB/FAX service, etc.)

SW 69-1~8

Dial disable in PB (PB/FAX service, etc.)

Make time (10PPS)

SW 63-1~4

Dial disable in pulse

Break time (10PPS)

SW 63-5~8

Dial disable in pulse

Minimum pause (10PPS)

SW 64-1~4

Dial disable in pulse

Minimum pause (20PPS)

SW 64-5~8

Dial disable in pulse

Make time (20PPS)

SW 65-1~4

Dial disable in pulse

Break time (20PPS)

SW 65-5~8

Dial disable in pulse

Signal 
detection

Busy tone detection

SW 71-3

Busy tone detection disable

Busy tone detection cycle

SW 71-4~5

Busy tone detection error

DT/BT detection level

SW 71-6~7

Busy tone detection disable

Dial tone detection

SW 70-6

Dial tone detection disable

Dial tone monitor time

SW 70-7

Dial tone detection error

Busy tone detection time lower limit

SW 72-1~2

Busy tone detection error

Busy tone detection time upper limit

SW 72-3~4

Busy tone detection error

DT/BT detection frequency range setup

SW 71-1~2

Dial tone/busy tone detection error

F-NET

SDT signal detection

SW  68-6

F-NET contract line

Redial

Remote 
machine not 
responding

Recalling when the remote machine does not 
respond.

SW 56-8

No recall wanted when remote machine 
not responding

Error

Number of recall in communication error

send setup

SW 57-5~8

Effective only when divided with SW59-1

Error

Recall allowed in communication error

Send setup

SW 59-3

Error

Recall interval in communication error

SW 58-5~8

Busy

Recall interval in communication busy

send setup

SW 57-1~4

Busy

Number of recall in busy

send setup

SW 58-1~4

Busy

Recall allowed in busy

send setup

SW 59-2

Reception 
(Calling)

Not receiving

Auto reception call number setup

Receive 
setup

SW 3-5~8

Number of reception call

Auto/Manual default setup

User setup

SW 7-2

Initial setup of auto reception/manual 
reception 

CI detection 
disable

Call signal ON time lower limit

SW 75-1~4

CI signal detection disable

Call signal ON time upper limit

SW 75-5~8

CI signal detection disable

Call signal OFF time lower limit

SW 76-1~4

Ci signal detection disable

Call signal OFF time upper limit

SW 76-5~6

CI signal detection disable

Call signal OFF not-detection time

SW 77-1~4

CI signal detection disable

F-NET 
contract line

1300Hz detection time

SW 68-7~8

When F-net no-ring reception is not 
made.

External 
telephone 
handset

External 
telephone 
connection

External telephone connection

Initial setup

SW 3-2

External telephone connection

External 
telephone off-
hook detection

External telephone off-hook detection time

SW 12-1~8

External telephone off-hook detection 
error

Remote 
switch number

Remote switch number setup

Initial setup

SW 13-1~8

Remote switch detection error

Remote 
switch setup

Remove reception command

SW 14-1

Remote switch inhibit

External telephone notification in remote 
switching

SW 14-2

Remote switch enable

SW 14-3

Remote switch is made when calling 
from external telephone.