Sharp AR-F14 (serv.man5) Service Manual ▷ View online
AR-F14/PN1 DISASSEMBLY AND ASSEMBLY 5-13
D. Interface transport section
(1) Decolor unit
a. Rear cabinet
1) Remove the screw (1 pc), and remove the maintenance cover.
2) Remove the four screws, and remove the rear cabinet.
2) Remove the four screws, and remove the rear cabinet.
b. Right cabinet
1) Open the manual feed tray.
2) Open the right door.
3) Remove the two screws, and remove the right cabinet.
3) Remove the two screws, and remove the right cabinet.
c. Decolor unit
1) Remove the connector of the decolor from the main unit.
2) Remove the four screws, and remove the decolor unit.
d. No. 2 paper exit sensor
1) Remove the No. 2 paper exit sensor, and remove the connector.
e. Tray detection switch
1) Remove the tray detection switch, and remove the connector.
f. DUP paper exit roller
1) Remove the screw, and remove the frame unit.
2) Remove the gear and the bearing. Remove the E-ring and the
bearing, and remove the DUP paper exit roller.
Maintenance cover
Rear cabinet
[05]DISASSEMBLYANDASSEMBLY.fm 13 ページ ２００４年４月１９日 月曜日 午後１時３８分
AR-F14/PN1 DISASSEMBLY AND ASSEMBLY 5-14
g. Decolor roller
1) Remove the frame unit.
2) Remove the E-ring, the gear, and the bearing. Remove the decolor
2) Remove the E-ring, the gear, and the bearing. Remove the decolor
roller.
*
When removing or attaching the roller, be careful of the actuator.
(2) Interface transport unit
a. Docking unit
1) Remove the screw, and slide the upper cover as shown in the figure.
2) Remove the screws C from the upper side of the front cover, and
2) Remove the screws C from the upper side of the front cover, and
remove the front cover and the docking unit.
3) Remove the two screws and remove the front cover.
4) Remove the four screws, and remove the left cover.
4) Remove the four screws, and remove the left cover.
5) Open the transport unit cover.
6) Remove the two screws A (M4 x 10).
6) Remove the two screws A (M4 x 10).
7) Pull out the transport unit to the copier unit guide.
8) Remove the docking unit connector, and pull it out.
8) Remove the docking unit connector, and pull it out.
b. Paper entry sensor 1
1) Remove the paper entry sensor 1, and remove the connector.
c. Photo sensor
1) Remove the photo sensor, and remove the connector.
d. Paper entry sensor 2
1) Remove the paper entry sensor 2, and remove the connector.
1
2
4
3
5
6
6
7
8
copier unit guide
[05]DISASSEMBLYANDASSEMBLY.fm 14 ページ ２００４年４月１９日 月曜日 午後１時３８分
AR-F14/PN1 DISASSEMBLY AND ASSEMBLY 5-15
e. Interface transport motor
1) Remove the connector and the screw, and remove the interface
transport motor.
f. Interface transport drive motor
1) Remove the jam release spring.
2) Pull the notch and release the lock, and raise the interface transport
upper unit.
3) Remove the interface transport lower unit.
4) Remove the interface transport earth wire.
5) Remove the E-ring, the belt, and the pulley. Remove the manual feed
auxiliary roller unit.
6) Remove the connector, the earth wire, and the screw. Remove the
interface transport motor unit. Remove the E-ring and the gear.
[05]DISASSEMBLYANDASSEMBLY.fm 15 ページ ２００４年４月１９日 月曜日 午後１時３８分
AR-F14/PN1 DISASSEMBLY AND ASSEMBLY 5-16
7) Remove the E-ring, and remove the interface transport drive roller
unit. Remove the bearing from the interface transport drive roller.
g. Interface transport medium roller 1, 2
1) Remove the interface transport lower unit.
2) Remove the interface transport earth wire.
3) Remove each part. Remove the manual feed auxiliary roller unit.
4) Remove the E-ring, and remove the interface transport medium roller
unit 1 and 2. Remove the bearing from the interface transport
medium roller 1 and 2.
h. Interface transport medium roller 3
1) Remove the interface transport lower unit.
2) Remove the interface transport earth wire.
2) Remove the interface transport earth wire.
3) Remove each part. Remove the manual feed auxiliary roller unit.
4) Remove the screw, and remove the transport paper guide.
5) Remove the E-ring, and remove the interface transport medium roller
unit 3. Remove the bearing from the interface transport medium
roller unit 3.
[05]DISASSEMBLYANDASSEMBLY.fm 16 ページ ２００４年４月１９日 月曜日 午後１時３８分
Click on the first or last page to see other AR-F14 (serv.man5) service manuals if exist.