DOWNLOAD Sharp AR-C260 (serv.man32) Service Manual ↓ Size: 6.42 MB | Pages: 127 in PDF or view online for FREE

■

■

■

■ Other optional equipment

●

●

●

●Print controller (AR-P16)

This is required to add printing or network
scanning capability to a machine not equipped for
printing as standard. This board also functions as
a printer controller that is required for use of the
network scanner function.

●

●

●

●Print server card (AR-NC5J)

This NIC card (Network Interface Card) is required
to connect a machine equipped with a print
controller for network printing and network
scanning functions.

●

●

●

●Network scanner expansion kit (AR-NS2)

This kit is required to add the network scanner
function. (The network scanner function is
scheduled to be supported in the spring of 2003.)

●

●

●

●Hard disk drive (AR-HD4)

This must be installed to use the job retention
function, which is used to temporarily hold print
data rather than immediately printing it out. The
hard disk drive is also required for the network
scanner function.
Models that have the printer controller as a
standard feature are also equipped with a built-in
hard disk drive.

Peripheral devices are basically optional, but are incorporated in some models as standard equipment.

■

■

■

■ Face-up and face-down output

After printing, the paper is delivered to the exit tray. This product has two exit trays (centre tray and left tray). The
paper specifications (page 8-3) and output conditions differ for each tray; however, if the paper and output
conditions are such that the paper can be delivered to either tray, you can select the tray to which the paper will
go.
● Paper exits to the centre tray face-down only.
● Paper exits to the left tray face-up only. However, if a duplex bypass/inverter unit has been installed, face-

down output is also possible. In this case, face-up or face-down output is automatically selected according to
the paper and output conditions (it is not possible to manually select face-up or face-down.)  

Whale_general-copy_EX.book  7 ページ  ２００２年１１月１３日　水曜日　午後４時５０分

The machine status, messages and touch keys are
displayed on the panel. The display will change to
show the status of printing, copying or network
scanning according to which mode is selected. For
details see the next page.

Use to change modes and the corresponding
display on the touch panel.

Press to enter the print mode. 

Print data can be received when this indicator is
lit.

Lights up or blinks when print data is being
received. Also lights up or blinks when printing is
being performed.

Press to enter the network scan mode when the
network scanner function is added. (See the
operation manual (for network scanner).)

Press to select the copy mode.

Press to display the current job status. (See page
1-10.)

Use to adjust the contrast of the touch panel or to
set key operator programs. (See page 2-13.)

Use to enter number values for various settings.

This key is used as an account control key for copy
and network scan features.

This key is used as a program key for copy
features.

This key is active for copy features.

This is used to make black and white copies and to
scan a black and white original when the network
scan function is used.

This key is active for copy and network scan
features.

This is used to make full-colour or single-colour
copies and to scan a colour original when the
network scanner function is used.

Whale_general-copy_EX.book  8 ページ  ２００２年１１月１３日　水曜日　午後４時５０分

[Example 1]

Items on the touch panel
are easily selectable by
touching the key associ-
ated with the item with a
finger. Selection of an
item will be
accompanied with a
beep tone to confirm the
item was selected. Also,
the key area for the item
will be highlighted for
visual confirmation.

[Example 2]

Keys which are greyed
out on any screen are
not selectable. If a
greyed out key is
touched, a double beep
will be sounded.

The confirmation beeps can be disabled by a key
operator program. (See page 8 of the key
operator's guide.)

The touch panel screens shown in this manual are
printed images, and may appear different from the
actual screens.

[Example 1]

Items which are
highlighted at the time a
screen appears are
already selected and will
be registered to function if
the [OK] key is touched.

[Example 2]

When the machine is
used in the copy mode,
the functions shown in
the table below can only
be set or cancelled on
the special feature
screen by alternate
touches of the function
keys on the panel.

[Example 3]

When the machine is
used in the copy mode
and a special feature is
selected, a
corresponding icon
representing the feature
will appear on the touch
key and on the main
screen of the mode
selected. If this icon is
touched, the setting
screen of the function (or
a menu screen) will
appear, allowing the
settings to be checked
or adjusted and the
function to be cancelled
easily.

JOB QUEUE

COPY

SHARP001

0666211221

003 / 00

003 / 00

010 / 00

SETS / PRO

1/13

Copier feature

● Dual page copy
● Centring
● Transparency inserts
● Mirror image
● A3 (11"x17") Full-bleed

CANCEL

OK

D

RIGHT 

BINDING

LEFT 

BINDING

COLOUR 

ADJUSTMENTS

 DUAL PAGE
 COPY

SPECIAL MODES

2-SIDED COPY

OUTPUT

READY TO COPY.

B4

P

OR

A3

A4

DUPLEX

Whale_general-copy_EX.book  9 ページ  ２００２年１１月１３日　水曜日　午後４時５０分

This screen is displayed when the [JOB STATUS] key on the operation panel is pressed.
A job list showing the current job at the top of the job queue or a list showing completed jobs can be displayed.
The contents of jobs can be viewed or jobs can be deleted from the queue.

This shows the current job and the jobs waiting to
be run. The icons to the left of the jobs in the queue
show the job mode.

The displayed jobs in the job list are themselves
operation keys. To cancel printing or to give a job
the highest print priority, touch the relevant job key
to select the job and execute the desired operation
using the keys described in 5 and 6.

When a job status display indicates "PAPER
EMPTY", the specified paper size for the job is not
loaded in any of the trays. 
In this case, the job will be suspended until the
required paper is loaded. Other stored jobs will be
printed (if possible) until the required paper is
loaded. (Other jobs will not be printed if the paper
runs out during printing.) If you need to change the
paper size because the specified paper size is not
available, touch the current job key to select it and
then touch the [DETAIL] key described in 6.

Use to display the print job list for print and copy
mode.

This displays a list of only the jobs that use the
network scanner function. (Only when the network
scanner function is added.)

Use to switch the page of the displayed job list.

Use to cancel or delete the current job or delete the
selected reserved job.

The key is only effective for computer print jobs and
only appears in the job status screen of the print
mode. It is used to display detailed information of a
selected print job and to change the paper size for
the print job.

JOB QUEUE

COPY

SHARP001

STATUS

PAPER EMPTY

003 / 000

PRINT JOB

SCANNER JOB

JOB QUEUE

DETAIL

STOP/DELETE

003 / 000

1/1

SETS / PROGRESS

WAITING

*

Copy mode

Print mode

Network scan mode

sec_whale_01_1.fm  10 ページ  ２００２年１１月１４日　木曜日　午前９時１２分