Sharp AR-C250 (serv.man6) User Manual / Operation Manual ▷ View online
1-5
CHAPTER
1
POWER ON AND OFF
The power switch is located on the left side of the copier. When the
power switch is turned to the “ON” position, the message “
power switch is turned to the “ON” position, the message “
WARMING
UP. PLEASE WAIT.
” will appear in the message display. Warming
up takes about 330 seconds. Once the copier is ready, the message
display will change to “
display will change to “
READY TO COPY.
”, and the START (
) key
indicators will light up, indicating that copying is possible.
If the copier has been programmed in the auditing mode, the message
“
If the copier has been programmed in the auditing mode, the message
“
ENTER YOUR ACCOUNT NUMBER. -----
” will appear after warming
up. Once a valid account number has been entered, copying will
become possible.
become possible.
GETTING STARTED
Power on and off
Power off
Power on
●
Be sure to extend the tray when paper sizes B4 (8-1/2"
x 14") or larger are to be received.
x 14") or larger are to be received.
1-6
CHAPTER
1
GETTING STARTED
Power on and off
Sleep mode
If the sleep mode is enabled, the copier will enter the mode once a
programmed length of time has elapsed without any copier
operation after the last copy of a run is made or the power is first
turned on. When the copier enters the sleep mode, the display on
the touch panel will disappear. In this condition, power is not
supplied to the fuser in the copier. To exit from the sleep mode,
press the COPY key.
If the sleep mode is enabled, the copier will enter the mode once a
programmed length of time has elapsed without any copier
operation after the last copy of a run is made or the power is first
turned on. When the copier enters the sleep mode, the display on
the touch panel will disappear. In this condition, power is not
supplied to the fuser in the copier. To exit from the sleep mode,
press the COPY key.
★ KEY OPERATOR See page 8-25 for setting the sleep mode timer. See
page 8-30 for enabling or disabling the sleep mode.
Preheat mode
The copier will enter the mode once the set time has elapsed without
any copier operation after the last copy of a run is made or power is
turned on.
When the copier enters the preheat mode, the message “
The copier will enter the mode once the set time has elapsed without
any copier operation after the last copy of a run is made or power is
turned on.
When the copier enters the preheat mode, the message “
PREHEAT
MODE. PLACE ORIGINALS
.” will appear.
In this condition, the fuser in the copier is maintained at a lower heat
level thereby saving power. The preheat level is, however, high
enough to allow the copier to come to a ready condition or begin
copying approximately 30 seconds after any key input is made.
To copy from the preheat mode, make desired copier selections and
press a START (
level thereby saving power. The preheat level is, however, high
enough to allow the copier to come to a ready condition or begin
copying approximately 30 seconds after any key input is made.
To copy from the preheat mode, make desired copier selections and
press a START (
,
) key using the normal copying
procedure.
★ KEY OPERATOR See page 8-26 for information on setting the preheat
mode.
POWER ON AND OFF
Power save modes
The copier has two power save modes to reduce overall power
consumption and thereby reduce the cost of operation and to conserve
natural resources to help reduce environmental pollution. The two
power save modes are preheat mode and sleep mode.
consumption and thereby reduce the cost of operation and to conserve
natural resources to help reduce environmental pollution. The two
power save modes are preheat mode and sleep mode.
★ KEY OPERATOR
The preheat activation time and the sleep activation time have been
preset at the factory to 15 min. for preheat mode and 60 min. for sleep
mode. These times can be changed as described in the key operator’s
guide section. It is suggested that you set appropriate times according to
the actual usage of the copier.
preset at the factory to 15 min. for preheat mode and 60 min. for sleep
mode. These times can be changed as described in the key operator’s
guide section. It is suggested that you set appropriate times according to
the actual usage of the copier.
The
E
NERGY
S
TAR
®
guidelines are
applied to the products only in
Europe, Australia and New
Zealand. The products that meet
the
Europe, Australia and New
Zealand. The products that meet
the
E
NERGY
S
TAR
®
guidelines carry
the logo shown above. The
products without the logo may not
meet the
products without the logo may not
meet the
E
NERGY
S
TAR
®
guidelines.
The Environmental Choice Program
guidelines are applied to the products
only in Canada. The products that
meet the Environmental Choice
Program guidelines carry the logo
shown above. The products without
the logo may not meet the
Environmental Choice Program
guidelines.
guidelines are applied to the products
only in Canada. The products that
meet the Environmental Choice
Program guidelines carry the logo
shown above. The products without
the logo may not meet the
Environmental Choice Program
guidelines.
1-7
CHAPTER
1
1
Press the INFORMATION (
) key in the standby mode.
●
The screen for the information categories will appear.
2
Select the “COPIER” key to display the first screen of
the copier feature items.
the copier feature items.
●
If the toner supply is not low, this screen is not displayed. Please
proceed to step 3.
proceed to step 3.
3
Select the feature you would like to know about by
pressing a copier feature item key on the touch panel.
pressing a copier feature item key on the touch panel.
●
If the feature you would like to know about is not displayed on the
touch panel, press the scroll (
touch panel, press the scroll (
) key on the touch panel until
the feature is displayed.
●
If a copier feature item key is pressed, the description for that
feature will appear. Use the scroll (
feature will appear. Use the scroll (
) key to display additional
information until all information for that feature has been displayed.
●
To return to the copier feature item screen, press the “INDEX”
key.
key.
●
To exit the INFORMATION mode, press the “EXIT” key on the
touch panel.
touch panel.
INFORMATION FUNCTION
The information function provides a quick reference guide to the use
of the various features and functions of this copier. The information
mode can be entered when the copier is in the standby mode.
of the various features and functions of this copier. The information
mode can be entered when the copier is in the standby mode.
GETTING STARTED
Information function
1
4
INFORMATION
CUSTOM
SETTINGS
EXIT
INFORMATION
SELECT INFORMATION.
COPIER
ADDING TONER
EXIT
MAKING 2-SIDED COPIES (2-SIDED COPY)
INFORMATION
SORTING COPIES INTO SETS OR STAPLING
FINISHED SETS OF COPIES (OUTPUT)
FINISHED SETS OF COPIES (OUTPUT)
USING THE DOCUMENT FEEDER
(DOCUMENT FEEDER)
REDUCTION/ENLARGEMENT/ZOOM
(COPY RATIO)
(COPY RATIO)
STORING FREQUENTLY USED JOB PROGRAMS
(PROGRAM)
(PROGRAM)
1/5
1-8
CHAPTER
1
USING THE TOUCH PANEL
How to use the touch panel
You can set or cancel a function displayed on the touch
panel by pressing (touching) a key with a finger. The touch
key operation can be confirmed with a beep tone (and
highlighting of the touch key).
panel by pressing (touching) a key with a finger. The touch
key operation can be confirmed with a beep tone (and
highlighting of the touch key).
★
★
★
★
★ KEY OPERATOR For the beep tone to be heard, the beep tone must be
enabled by a key operator program. See page 8-27.
A transparent status function key represents unavailability
of that function. If a transparent status key is pressed, two
short beeps will sound.
of that function. If a transparent status key is pressed, two
short beeps will sound.
Selection of function
To register the selected settings for a function, press the
“OK” key on the setting screen. The settings indicated by
a highlighted display will be registered as a selected function.
“OK” key on the setting screen. The settings indicated by
a highlighted display will be registered as a selected function.
Some special functions can be selected by pressing the
relevant keys on the SPECIAL MODES screen (page 3-4) or
on the IMAGE EDIT menu (page 3-24) to highlight the keys.
To cancel these functions, press the relevant keys again to
return the keys to the normal display. These functions are:
Dual page copying, Centring, Transparency inserts, Neg./
pos. reverse, Mirror image, and A3 (11x17) full-bleed.
relevant keys on the SPECIAL MODES screen (page 3-4) or
on the IMAGE EDIT menu (page 3-24) to highlight the keys.
To cancel these functions, press the relevant keys again to
return the keys to the normal display. These functions are:
Dual page copying, Centring, Transparency inserts, Neg./
pos. reverse, Mirror image, and A3 (11x17) full-bleed.
GETTING STARTED
Using the touch panel
READY TO COPY.
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
1.
2.
3.
A4
A3
B4
60~105
g
/m
2
106~130
g
/m
2
131~200
g
/m
2
TRANSPARENCY
PAPER TYPE
STORE/DELETE
RECALL
1
2
3
4
5
6
7
8
9
ERASE
CANCEL
10
OK
OK
(0~20)
mm
EDGE ERASE
CENTRE ERASE
EDGE+CENTRE
ERASE
READY TO COPY.
SPECIAL MODES
MARGIN SHIFT
ERASE
IMAGE EDIT
COVERS
CENTRING
DUAL PAGE
COPY
COLOUR
ADJUSTMENTS
TRANSPARENCY INSERTS
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO
A4
Click on the first or last page to see other AR-C250 (serv.man6) service manuals if exist.