Sharp AR-C250 (serv.man6) User Manual / Operation Manual ▷ View online
2-15
CHAPTER
2
Two-sided copying with bypass tray
Two-sided copies can be made manually using the bypass tray. The
procedure described below is useful for users of the copier without an
optional duplex module (AR-DU2).
procedure described below is useful for users of the copier without an
optional duplex module (AR-DU2).
1
Place the first original face down on the document glass
and make a copy.
and make a copy.
●
The first side of the copy can be made using any of the paper feed
stations.
stations.
2
Remove the first original and place the second original
face down on the document glass.
face down on the document glass.
●
Make sure the first and second originals are oriented in the same
way on the document glass.
way on the document glass.
●
If an optional document feeder is used, the originals must be fed
one at a time.
one at a time.
3
Turn the first copy over without changing its top-bottom
orientation and place it into the bypass tray.
orientation and place it into the bypass tray.
●
Be sure to feed the copies one sheet at a time.
4
Press the “PAPER SELECT” key and select the desired
paper type in the bypass tray section.
paper type in the bypass tray section.
5
Press the COLOUR COPY START (
) key or BLACK
COPY START (
) key.
SPECIAL PAPERS (manual feed)
MAKING COPIES
Special papers (manual feed)
1 2
1 2
3 4
3 4
1 2
C
CA
CLEAR
INTERRUPT
CLEAR
ALL
ER SELECT
100%
COPY RATIO
INFORMATION
CUSTOM
SETTINGS
PAPER TYPE
.
.
.
A4
A3
B4
A4
60~105
g
/m
2
106~130
g
/m
2
131~200
g
/m
2
TRANSPARENCY
2-16
CHAPTER
2
Automatic
This is the standard initial setting for this copier. In this mode, the
characteristics of an original being copied are “read” by the exposure
system, and exposure adjustments are made automatically.
This optimizes the contrast of the copied images.
characteristics of an original being copied are “read” by the exposure
system, and exposure adjustments are made automatically.
This optimizes the contrast of the copied images.
Original image type
TEXT/PRTD. PHOTO:
This mode provides the best balance for copying
an original which contains both text and printed
photographs.
an original which contains both text and printed
photographs.
TEXT:
This mode is useful in enhancing very low density
areas of an original or in suppressing unusually
high-density background areas.
areas of an original or in suppressing unusually
high-density background areas.
TEXT/PHOTO:
This mode provides the best balance for copying
an original which contains both text and
photographs.
an original which contains both text and
photographs.
PRINTED PHOTO: This mode is useful for copying printed
photographs.
PHOTO:
This mode provides the best copies of photographs
with fine details.
with fine details.
MAP:
This mode is useful to provide the best shading
and fine details found on most maps.
and fine details found on most maps.
COPY OF COPY: This mode provides the better adjustment for the
printed originals such as copied text or copied
photo. If the check box is checked, only Text/prtd.
photo, Text and Printed photo mode keys are
shown on the touch panel, then select the type of
original among them. The exposure can only be
adjusted manually.
photo. If the check box is checked, only Text/prtd.
photo, Text and Printed photo mode keys are
shown on the touch panel, then select the type of
original among them. The exposure can only be
adjusted manually.
EXPOSURE ADJUSTMENTS
Exposure selections for this copier should be selected according to
the type of originals being copied: TEXT/PRTD. PHOTO, TEXT,
TEXT/PHOTO, PHOTO, PRINTED PHOTO or MAP. (Refer to the
samples on page 4 to see the effects on copy images in relation to
the EXPOSURE ADJUSTMENTS.) If the original image type is
TEXT/PRTD. PHOTO, TEXT or TEXT/PHOTO, the exposure can be
adjusted automatically or manually. If the original image type is
PHOTO, PRINTED PHOTO or MAP, the exposure can be adjusted
manually only. Also if the COPY OF COPY mode is selected, it allows
only TEXT/PRTD. PHOTO, TEXT and PRINTED PHOTO image
types for the better copy result and the exposure can be adjusted
manually only. The standard initial setting of the original image type
for this copier is TEXT/PRTD. PHOTO.
the type of originals being copied: TEXT/PRTD. PHOTO, TEXT,
TEXT/PHOTO, PHOTO, PRINTED PHOTO or MAP. (Refer to the
samples on page 4 to see the effects on copy images in relation to
the EXPOSURE ADJUSTMENTS.) If the original image type is
TEXT/PRTD. PHOTO, TEXT or TEXT/PHOTO, the exposure can be
adjusted automatically or manually. If the original image type is
PHOTO, PRINTED PHOTO or MAP, the exposure can be adjusted
manually only. Also if the COPY OF COPY mode is selected, it allows
only TEXT/PRTD. PHOTO, TEXT and PRINTED PHOTO image
types for the better copy result and the exposure can be adjusted
manually only. The standard initial setting of the original image type
for this copier is TEXT/PRTD. PHOTO.
When copying a coloured original in the Black/White copy mode, a
coloured background with text in the background area may be
reproduced with the text unclear. Check with the key operator for
the setting of “Disabling of Pre-scan in B/W Copy” program (see
page 8-30). If pre-scan is enabled, text may be reproduced with
improved clarity.
coloured background with text in the background area may be
reproduced with the text unclear. Check with the key operator for
the setting of “Disabling of Pre-scan in B/W Copy” program (see
page 8-30). If pre-scan is enabled, text may be reproduced with
improved clarity.
MAKING COPIES
Exposure adjustments
AUTO
EXPOSURE
2-17
CHAPTER
2
MAKING COPIES
Exposure adjustments
1
Press the “EXPOSURE” key on the touch panel.
2
Select “TEXT/PRTD. PHOTO”, “TEXT”, “TEXT/PHOTO”,
“PRINTED PHOTO”, “PHOTO”, or “MAP” depending on
the original.
“PRINTED PHOTO”, “PHOTO”, or “MAP” depending on
the original.
●
When making a copy from a copy made by the AR-C250,
checking the box of COPY OF COPY then choosing the proper
alternatives depending upon the content of the original allows for
the best result.
checking the box of COPY OF COPY then choosing the proper
alternatives depending upon the content of the original allows for
the best result.
●
When checking the COPY OF COPY check box, TEXT/
PRTD.PHOTO, TXT and PRINTED PHOTO can be selected.
PRTD.PHOTO, TXT and PRINTED PHOTO can be selected.
3
If “TEXT/PRTD. PHOTO”, “TEXT” or “TEXT/PHOTO”
has been selected in step 2, select “AUTO” or “MANUAL”.
has been selected in step 2, select “AUTO” or “MANUAL”.
●
When the COPY OF COPY check box is checked, the exposure
is automatically set to “MANUAL”.
is automatically set to “MANUAL”.
4
If the manual mode has been selected, use the
and
keys to adjust the copy density as desired.
EXPOSURE ADJUSTMENTS
UTPUT
AUTO
EXPOSURE
PAPE
AUTO
TEXT/
PRTD.PHOTO
TEXT
PRINTED
PHOTO
COPY
OF COPY
TEXT/PHOTO
PHOTO
MAP
100%
A4
AUTO
OK
TE
PRTD.
TE
PRI
PH
CO
OF
AUTO
MANUAL
AUTO
SIDED
OPY
UTPUT
TEXT/
PRTD.PHOT
TEXT
PRINTED
PHOTO
COPY
OF COPY
EXPOSURE
AUTO
MANUAL
PAPER SELECT
A4
AUTO
OUTPUT
2-SIDED
COPY
2-18
CHAPTER
2
JOB MEMORY
Frequently used job programs can be stored in one of nine storage
registers. This is convenient for quick job recall without losing time
manually reprogramming each aspect of the job.
registers. This is convenient for quick job recall without losing time
manually reprogramming each aspect of the job.
●
All functions that can be set in the copy mode except the copy
quantity setting can be stored in the job memory.
quantity setting can be stored in the job memory.
●
If any function which has been stored in a job program is modified
by a key operator program, the key operator settings will supercede
the previous setting.
by a key operator program, the key operator settings will supercede
the previous setting.
★ KEY OPERATOR
Job memory replacement/deletion can be
prohibited. See page 8-28.
Storing a job program
1
Press the PROGRAM (
P
) key.
●
The JOB PROGRAMS screen will appear on the touch panel.
2
Press the “STORE/DELETE” key on the touch panel.
●
To cancel the job memory mode, press the “EXIT” key or the
CLEAR ALL (
CLEAR ALL (
CA
) key.
3
Select a program number from 1 to 9 on the touch panel.
●
The numbers which are highlighted are job registers which
already contain job programs.
already contain job programs.
●
If a program number containing a registered job program is
selected, a message will appear to confirm the selection. To
replace a stored job program with a new program, press the
“STORE” key and proceed to the next step.
To cancel replacement, press the “CANCEL” key.
selected, a message will appear to confirm the selection. To
replace a stored job program with a new program, press the
“STORE” key and proceed to the next step.
To cancel replacement, press the “CANCEL” key.
4
Make all copier selections to be stored.
5
Press the “OK” key to complete the storage.
MAKING COPIES
Job memory
8
9
0
P
C
CLEAR
PROGRAM
IT
STORE/DELETE
RECALL
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
JOB PROGRAMS
STORE/DELETE
RECALL
PRESS PROGRAM NUMBER.
EXIT
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
MAKE COPIER SELECTIONS AND PRESS
[OK].
OK
CANCEL
A4
A3
B4
B4
AUTO
A4
Click on the first or last page to see other AR-C250 (serv.man6) service manuals if exist.