Sharp AR-507 (serv.man7) User Manual / Operation Manual ▷ View online
2-3
CHAPTER
2
USING THE RSPF
●
The RSPF can handle a maximum of 50 originals in
A4 (8-1/2" x 11") paper size.
A4 (8-1/2" x 11") paper size.
●
1-sided to 2-sided, 2-sided to 1-sided, and 2-sided to
2-sided copying can be performed.
2-sided copying can be performed.
●
The originals must be set face up in the document
feeder tray.
feeder tray.
●
Different size originals with the same width can be
placed in the document feeder tray and automatically
copied onto copy paper of their respective sizes.
The automatic copy ratio selection will not function in
this case. Also, some special functions might not be
properly activated.
placed in the document feeder tray and automatically
copied onto copy paper of their respective sizes.
The automatic copy ratio selection will not function in
this case. Also, some special functions might not be
properly activated.
●
When using large originals such as B4 and A3 (8-1/2"
x 14" and 11" x 17") sizes, unfold the auxiliary tray.
x 14" and 11" x 17") sizes, unfold the auxiliary tray.
The RSPF (reversing single pass feeder) will handle
multiple originals.
multiple originals.
●
Before loading originals into the document feeder
tray, be sure to remove any staples or paper clips
from them.
tray, be sure to remove any staples or paper clips
from them.
●
Damaged or crumpled originals or originals which
have been folded may misfeed in the RSPF or cause
incorrect size detection. It is recommended that these
be copied from the document glass and the copies be
used as original documents.
have been folded may misfeed in the RSPF or cause
incorrect size detection. It is recommended that these
be copied from the document glass and the copies be
used as original documents.
●
When feeding originals which have closely spaced
binding holes punched along an edge, place the
originals so that the punched edge is positioned to the
right or along the side guides.
binding holes punched along an edge, place the
originals so that the punched edge is positioned to the
right or along the side guides.
●
Special originals such as transparency film and tracing
paper should not be fed from the RSPF, but should be
placed on the document glass.
paper should not be fed from the RSPF, but should be
placed on the document glass.
●
Duplex copying will not work when a non-standard
sized paper (or 5-1/2" x 8-1/2" paper) is used.
sized paper (or 5-1/2" x 8-1/2" paper) is used.
●
If the orientation of the originals does not match that
of the copy paper when both the originals and copy
paper are of standard sizes and the auto paper select
mode or automatic copy ratio select mode is on, the
image of the originals will be automatically rotated to
match the copy paper. If enlargement copying onto a
paper size larger than A4 (8-1/2" x 11") is performed
and in case of 100% copying onto a paper size larger
than B4 (8-1/2" x 14"), however, the image will not be
rotated.
of the copy paper when both the originals and copy
paper are of standard sizes and the auto paper select
mode or automatic copy ratio select mode is on, the
image of the originals will be automatically rotated to
match the copy paper. If enlargement copying onto a
paper size larger than A4 (8-1/2" x 11") is performed
and in case of 100% copying onto a paper size larger
than B4 (8-1/2" x 14"), however, the image will not be
rotated.
●
Image loss (max. 5mm (13/64")) can occur along the
leading and trailing edges of the copies. Also image
loss (max. 5mm (13/64") in total) can occur along the
other edges of the copies.
leading and trailing edges of the copies. Also image
loss (max. 5mm (13/64") in total) can occur along the
other edges of the copies.
MAKING COPIES
Using the RSPF
Example) Same-size copying from A4 (8-1/2" x 11") original
onto A3 (11" x 17") paper
Copying from
the document
glass
the document
glass
Copy
Copying from
the RSPF
the RSPF
Original
Top
Bottom
Top
Bottom
Example) Enlargement copying onto copy paper of
the same size as the original
Copying from
the document
glass
the document
glass
Copy
Copying from
the RSPF
the RSPF
Original
Top
Bottom
Top
Bottom
NOTE:
●
The original image positions on the copies are different concerning the leading edge position between copying from
the RSPF and copying from the document glass. In some cases, the desired copy cannot be obtained from the
normal orientation of the originals. The image position can be changed by rotating the original. When the optional
staple sort mode is used, however, the stapling position may not be proper.
the RSPF and copying from the document glass. In some cases, the desired copy cannot be obtained from the
normal orientation of the originals. The image position can be changed by rotating the original. When the optional
staple sort mode is used, however, the stapling position may not be proper.
1. Different image positions on the copy
Same-size copying onto a larger size copy is
performed.
performed.
2. Different copy image ranges
Enlargement copying is performed onto copy paper
of the same size as the original and part of image is
out of the copy.
of the same size as the original and part of image is
out of the copy.
Stream feeding mode
If the stream feedng mode has been enabled using a
key operator program, the message “
If the stream feedng mode has been enabled using a
key operator program, the message “
NEWLY PLACED
O R I G I N A L S W I L L B E F E D A N D C O P I E D
AUTOMATICALLY.
AUTOMATICALLY.
” will appear for approximately 5
seconds after feeding of all originals is completed.
While this message is displayed, any new originals
placed in the document feeder tray will be fed and
copied automatically.
While this message is displayed, any new originals
placed in the document feeder tray will be fed and
copied automatically.
★ KEY OPERATOR See page 8-19 for information on
setting the stream feeding mode.
2-4
CHAPTER
2
1-sided copies of 1-sided originals
1
Adjust the original guides to the size of the originals and
set the originals face up in the document feeder tray.
set the originals face up in the document feeder tray.
●
The original size will be indicated on the touch panel, and the
paper tray with the corresponding paper size will be automatically
selected.
paper tray with the corresponding paper size will be automatically
selected.
●
Be sure to remove any original from the document glass before
setting the originals in the document feeder tray. However, if an
original has been placed on the document glass, copying will be
setting the originals in the document feeder tray. However, if an
original has been placed on the document glass, copying will be
performed from the RSPF when the START (
) key is pressed.
●
If copy paper of the required size is not installed in any of the
trays, the following message will appear.
trays, the following message will appear.
LOAD
PAPER.
If a tray of the required size is not installed, use the bypass tray
and press the “PAPER SELECT” key on the touch panel to select
the bypass tray.
and press the “PAPER SELECT” key on the touch panel to select
the bypass tray.
●
To copy onto a different size paper, use the “PAPER SELECT”
key to make the selection.
key to make the selection.
2
Ensure that the 1-sided to 1-sided copying mode is
selected on the touch panel.
selected on the touch panel.
●
When no icon is displayed in the area indicated in the illustration
(
(
), the 1-sided to 1-sided copying mode is selected.
●
If the 1-sided to 1-sided mode is not selected, press the
2-SIDED COPY key and then press the 1-sided to 1-sided key
(
2-SIDED COPY key and then press the 1-sided to 1-sided key
(
) on the touch panel. Press the “OK” key to return to the
basic screen.
3
Use the 10-key pad to enter the desired number of
copies.
copies.
●
The number will be shown in the copy quantity display of the
touch panel.
touch panel.
●
Use the CLEAR (
C
) key to cancel an entry if a mistake has been
made.
●
If you set a multiple number of copies, the copies will be delivered
collated. To deliver in the GROUP mode, press the OUTPUT key
and then select “GROUP” on the touch panel. See page 2-17.
collated. To deliver in the GROUP mode, press the OUTPUT key
and then select “GROUP” on the touch panel. See page 2-17.
4
Press the START (
) key.
●
To cancel a copy run, press the CLEAR ALL (
CA
) key. Copying
will stop and the RSPF will output any originals which have been
fed. Also, the number in the copy quantity display will be reset to
0.
fed. Also, the number in the copy quantity display will be reset to
0.
MAKING COPIES
Using the RSPF
USING THE RSPF
READY TO COPY. (DOCUMENT FEEDER MODE)
1.
2.
A4
A3
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
A4
106~200
g
/m
2
ORIGINAL
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
C
CLEAR
INTERRUPT
CA
CLEAR ALL
START
Maximum height
line
line
2-5
CHAPTER
2
MAKING COPIES
Using the RSPF
USING THE RSPF
2-sided copies from 1-sided originals
1
Adjust the original guides to the size of the originals and
set the originals face up in the document feeder tray.
set the originals face up in the document feeder tray.
2
Press the 2-SIDED COPY key.
3
Press the
key on the touch panel.
4
Press the “OK” key.
5
Enter the desired number of copies.
6
Press the START (
) key.
●
To cancel a copy run during duplex copying, press the CLEAR
ALL (
ALL (
CA
) key.
AUTO
1
2
3
4
5
6
7
8
9
0
P
PROGRAM
AUDIT CLEAR
INT
CA
CLEAR ALL
START
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
OK
AUTO A4
Maximum height
line
line
2-6
CHAPTER
2
MAKING COPIES
Using the RSPF
USING THE RSPF
2-sided copies from 2-sided originals
1
Adjust the original guides to the size of the originals and
set the originals face up in the document feeder tray.
set the originals face up in the document feeder tray.
2
Press the 2-SIDED COPY key.
3
Press the
key on the touch panel.
4
Press the “OK” key.
5
Enter the desired number of copies.
6
Press the START (
) key.
●
To cancel a copy run during duplex copying, press the CLEAR
ALL (
ALL (
CA
) key.
AUTO
1
2
3
4
5
6
7
8
9
0
P
PROGRAM
AUDIT CLEAR
INT
CA
CLEAR ALL
START
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO A4
READY TO COPY.(DOCUMENT FEEDER MODE)
2-SIDED COPY
OK
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
AUTO
A4
Maximum height
line
line
Click on the first or last page to see other AR-507 (serv.man7) service manuals if exist.