DOWNLOAD Sharp AR-507 (serv.man7) Service Manual ↓ Size: 4.04 MB | Pages: 127 in PDF or view online for FREE

READY TO COPY. 

EXPOSURE

PAPER SELECT

COPY RATIO

2. A3

A4

A4R

106~200

g

/m

2

ORIGINAL

Press to set key operator programs or adjust the

contrast of the touch panel.

Press to select the 1-sided to 1-sided, 1-sided to

2-sided, 2-sided to 1-sided or 2-sided to 2-sided

copy mode.

Press to select the finisher mode: SORT or

GROUP.

Press to select the network scanner function.

(Optional Printer Expansion Kit and Network

Scanner Expansion Kit must be installed.)

Indicates the selected exposure mode.

EXPOSURE key (p. 2-16)

Press to select the exposure mode: AUTO,

TEXT, TEXT/PHOTO, or PHOTO.

Displays the selected paper size. When “AUTO”

is displayed, paper size matching the original and

copy ratio will be automatically selected.

Press to select the desired paper tray.

Displays the copy ratios for reductions or

enlargements.

Press to select a reduction or enlargement copy

ratio or select the automatic copy ratio selection

mode.

Press to check the settings of selected functions.

Initial settings
The copier assumes the initial settings when it is
turned on, when the CLEAR ALL (

CA

) key is pressed,

and approximately 1 minute after the last copy is
made in any mode.

●

Copy ratio:  100%

●

Automatic exposure

●

Copy quantity:  0

●

All special copier modes are set to off.

●

Tray select:  Paper tray 1
Optional large capacity tray will be selected when
installed.

★ KEY OPERATOR

Part names and functions

The document glass and the document feeder cover must be kept
clean to avoid dirty areas from being copied onto the copies.

●

If necessary, dampen the cloth with water. Do not use thinner,
benzene, or similar volatile cleaning agents.

User maintenance

●

If black lines appear on copies when copying with the RSPF,
wipe the parts shown in the illustration with a soft, clean cloth
dampened with plain water or water containing a small amount
of neutral detergent.

RSPF scanning
section glass

Scanning
guide

The contrast of the touch panel can be adjusted as below.

~200

g

/m

2

ETTINGS

 

DISPLAY

CONTRAST

KEY OPERATOR

PROGRAMS

TTINGS

ONTRAST

LIGHTER

DARKER

TER

DARKER

Touch panel contrast adjustment

Specifications

Type

Desktop

Copy system

Dry, electrostatic transfer system

Originals

Sheets, bound documents

Original feed system

Reversing single pass feeder (RSPF)

Original sizes

Max. A3 (11" x 17")

Copy sizes

Max. A3 (11" x 17"), min. A6 (5-1/2" x 8-1/2")
Image loss:

Max. 5 mm (13/64")
(both leading and trailing edges)
Max. 5 mm (13/64")
(along all other edges in total)

For paper weight, see page 4-2.

Copying speed

50 copies/min. (A4 (8-1/2" x 11"))

(at 100% copy ratio)

35 copies/min. (A4R (8-1/2" x 11"R))
29 copies/min. (B4 (8-1/2" x 14"))
25 copies/min. (A3 (11" x 17"))

Continuous copy

Max. 999 copies; subtractive counter

First-copy time*

Approx. 4.3  sec.

Warm-up time

Less than 150 sec.

Copy ratio

Variable: 25 to 400% in 1% increments, total 376 steps
(can be set in the horizontal and vertical directions
independently)
Fixed presets: 25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200%, 400% (25%, 50%, 64%, 77%, 95%, 100%, 121%,
129%, 141%, 200%, 400%)

Exposure system

Document glass:

Moving optical source (stationary platen) with
automatic exposure function

RSPF:

Moving original

Copy paper feed

Two paper trays with automatic paper feed (500 sheets each);
one bypass tray with 50-sheet automatic feed capability

Fusing system

Heat rollers

Developer system

Magnetic brush development

Light source

Xenon lamp

Resolution

Scan:

400 dpi

Output: 600 dpi

Gradation

Scan:

256 levels

Output: 2 levels (normal copying)

Required power supply

Local voltage ±10% (For this copier’s power supply requirements,
see the name plate located on the left hand side at the rear corner of
the copier.)

* When the copier is in the noise level reduce mode, the first copy time will be several seconds longer.