DOWNLOAD Sharp AR-405 (serv.man9) Service Manual ↓ Size: 693.07 KB | Pages: 18 in PDF or view online for FREE

Model
AR-405 (serv.man9)
Pages
18
Size
693.07 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / AR405 Service Manual-Setting and Adjustments
File
ar-405-sm9.pdf
Date
PREV: Sharp AR-405 (serv.man8) Service Manual

Sharp AR-405 (serv.man9) Service Manual ▷ View online

2) Disconnect the connector from the CN9 on the control PWB, and
connect the short connector (OCW4074K526//) instead.
3) Remove the ADF/RADF top cover, and set the DIP switch on the
control PWB to the desired test mode. While pressing the push
switch ON, turn on the power of the machine. 
(With the above operation, the machine enters the test mode.)
4) Turn on the push switch on the control PWB.
(Test operation is started.)
(To switch to another test mode, set the DIP switch on the control
PWB to the desired test mode, and open/close the ADF/RADF paper
feed section cover (microswitch FGOD it turned OFF and ON).
•
DIP switch 3 meaning
ON
OFF
DIP switch 3
For AB series
For inch series
•
Kinds of test modes and setting of DIP switch
No.
Test mode name
DIP switch
a
Single paper pass mode
All OFF
b
Duplex paper pass mode
1 ON,
the others OFF
c
Single aging mode
1, 3 ON,
2, 4, 5 OFF
d
Duplex aging mode
4 ON,
the others OFF
e
Load check mode
1, 5 ON,
2, 3, 4, OFF
f
EEPROM initializing mode + all
sensors adjustment mode
3, 5 ON,
1, 2, 4, OFF
g
Resist sensor adjustment mode
4, 5 ON,
1, 2, 3, OFF
h
Timing sensor adjustment mode
1, 4, 5, ON,
2, 3, OFF
i
Paper exit sensor adjustment mode
(AR-RF1 only)
3, 4, 5, ON,
1, 2, OFF
a. Single paper pass mode (with paper)
When documents are set on the paper feed tray, the document feed
LED lights up. When the push switch is pressed, all documents on the
paper feed tray are fed.
b. Duplex paper pass mode (with paper)
When documents are set on the paper feed tray, the document feed
LED lights up. When the push switch is pressed, all documents on the
paper feed tray are fed.
c. Single aging mode (without paper)
When the push switch is pressed, aging is started. The operation
timing is made by detection of each document size on the tray.  
d. Duplex aging mode (without paper)
When the push switch is pressed, aging is started. The operation
timing is made by detection of each document size on the tray.  
e. Load check mode
Set the DIP switch on the contro PWB as shown below, and open
and close the ADF/ RADF paper feed section cover to enter the load
check mode.
(DIP switch)
Every time when the push switch is pressed, the operation is per-
formed in the sequence of 1) 
∼
 21)
 1) Document feed LED ON, Document remain LED ON, Paper
feed solenoid ON
  2) Reverse solenoid ON, Paper feed solenoid OFF
  3) Document feed LED OFF, Document remain LED OFF, Reverse
solenoid OFF
 4) Document feed LED ON, Document remain LED OFF, Paper
feed solenoid ON, Paper feed motor forward rotation 450mm/s
(Preliminary paper feed operation)
  5) Document feed LED OFF, Document remain LED OFF, Paper
feed solenoid OFF, Paper feed motor OFF
 6) Document feed LED ON, Document remain LED ON, Paper
feed motor reverse rotation 450mm/2 (2-step advanced feed)
  7) Document feed LED OFF, Document remain LED OFF, Paper
feed motor OFF
 8) Document feed LED ON, Document remain LED ON, Paper
feed motor reverse rotation 850mm/s (Paper feed operation)
  9) Document feed LED OFF, Document remain LED OFF, Paper
feed motor OFF
10) Document feed LED ON, Document remain LED ON, Transport
motor forward rotation 867mm/s
11) Document feed LED OFF, Document remain LED OFF,
Transport motor OFF
12) Document feed LED ON, Document remain LED ON, Transport
motor reverse rotation 867mm/s
13) Document feed LED OFF, Document remain LED OFF,
Transport motor OFF
14) Document feed LED ON, Document remain LED ON, Reverse
motor forward rotation 867mm/s (reverse operatoin)
15) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
16) Document feed LED ON, Document remain LED ON, Reverse
motor forward rotation 867mm/s (Pulling/paper exit operation)
1)
2)
OFF
ON
SW
No.1
2
3
4
5
AR-405
1/21/1999
7 – 26
17) Reverse motor speed reduction 867 
→
 297mm/s (Paper exit
speed reduction)
18) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
19) Document feed LED ON, Document remain LED ON, Reverse
motor forward rotation 867mm/s (Paper exit operation)
20) Reverse motor speed reduction 867 
→
 297mm/s (Paper exit
speed reduction)
21) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
Kind of JAM, error
LED display
Paper feed motor lock
error
REMOVE ORIGINAL LED blinks at
the cycle of 2000msec.
Return to 1).
f. EEPROM initializing + all sensors adjustment mode
When the DIP switch is set (3, 5 to ON, 1, 2, 4 to OFF) the push
switch is pressed, the EEPROM is initialized. At that time, the LED
blinks at the cycle of 100msec.
After completion of EEPROM initializing, the LED turns ON. In case of
an error in the EEPROM initializing, the LED blinks at the cycle of
2000msec.
Then all sensors adjustment is started. At that time, the document
remain LED blinks at the cycle of 100msec. After completion of all
sensors adjustment, the document remain LED turns ON. In case of
an. Error in the all sensors adjustment, the document remain LED
blinks at the cycle of 2000msec.
*
Only when the EEPROM is successfully completed, the all sensors
adjustment is performed. 
Kinds of JAM, error
LED display
EEPROM initializing
error
Ready LED blinks at the cycle of
2000msec.
All sensors adjustment
error
Document remain LED blinks at the
cycle of 2000msec
g. Resist sensor adjustment mode 
Set the DIP switch (4, 5 to ON, 1, 2, 3 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.  
After completion of the sensor adjustment, the LED turns ON. In case of
an error in the sensor adjustment, the LED blinks at the cycle of 100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
h. Timing sensor adjustment mode 
Set the DIP switch (1, 4, 5 to ON, 2, 3 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.  
After completion of the sensor adjustment, the LED turns ON. In case
of an error in the sensor adjustment, the LED blinks at the cycle of
100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
i. Paper exit sensor adjustment mode
Set the DIP switch (3, 4, 5 to ON, 1, 2 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.
After completion of the sensor adjustment, the LED turns ON. In case
of an error in the sensor adjustment, the LED blinks at the cycle of
100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
(4) Kinds of error (RADF single mode only)
Kinds of JAM, error
LED display
Not-reaching/remaining JAM in
the paper feed section
Document remain LED blinks
at the cycle of 1000msec.
Not-reaching/remaining JAM in
the paper exit section
Ready LED blinks at the cycle
of 1000msec.
Paper feed motor lock error
Document remain LED blinks
at the cycle of 2000msec.
Resist/timing sensor
adjustment error (when power
is supplied)
Document remain LED blinks
at the cycle of 100msec.
Paper exit sensor adjustment
error (when power is supplied)
Ready LED blinks at the cycle
of 100msec.
A JAM/motor lock error can be canceled by opening/closing the ADF
after jam recovery process or by applying the power again. 
AR-405
7 – 27
1/21/1999
17) Reverse motor speed reduction 867 
→
 297mm/s (Paper exit
speed reduction)
18) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
19) Document feed LED ON, Document remain LED ON, Reverse
motor forward rotation 867mm/s (Paper exit operation)
20) Reverse motor speed reduction 867 
→
 297mm/s (Paper exit
speed reduction)
21) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
Kind of JAM, error
LED display
Paper feed motor lock
error
REMOVE ORIGINAL LED blinks at
the cycle of 2000msec.
Return to 1).
f. EEPROM initializing + all sensors adjustment mode
When the DIP switch is set (3, 5 to ON, 1, 2, 4 to OFF) the push
switch is pressed, the EEPROM is initialized. At that time, the LED
blinks at the cycle of 100msec.
After completion of EEPROM initializing, the LED turns ON. In case of
an error in the EEPROM initializing, the LED blinks at the cycle of
2000msec.
Then all sensors adjustment is started. At that time, the document
remain LED blinks at the cycle of 100msec. After completion of all
sensors adjustment, the document remain LED turns ON. In case of
an. Error in the all sensors adjustment, the document remain LED
blinks at the cycle of 2000msec.
*
Only when the EEPROM is successfully completed, the all sensors
adjustment is performed. 
Kinds of JAM, error
LED display
EEPROM initializing
error
Ready LED blinks at the cycle of
2000msec.
All sensors adjustment
error
Document remain LED blinks at the
cycle of 2000msec
g. Resist sensor adjustment mode 
Set the DIP switch (4, 5 to ON, 1, 2, 3 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.  
After completion of the sensor adjustment, the LED turns ON. In case of
an error in the sensor adjustment, the LED blinks at the cycle of 100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
h. Timing sensor adjustment mode 
Set the DIP switch (1, 4, 5 to ON, 2, 3 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.  
After completion of the sensor adjustment, the LED turns ON. In case
of an error in the sensor adjustment, the LED blinks at the cycle of
100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
i. Paper exit sensor adjustment mode
Set the DIP switch (3, 4, 5 to ON, 1, 2 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.
After completion of the sensor adjustment, the LED turns ON. In case
of an error in the sensor adjustment, the LED blinks at the cycle of
100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
(4) Kinds of error (RADF single mode only)
Kinds of JAM, error
LED display
Not-reaching/remaining JAM in
the paper feed section
Document remain LED blinks
at the cycle of 1000msec.
Not-reaching/remaining JAM in
the paper exit section
Ready LED blinks at the cycle
of 1000msec.
Paper feed motor lock error
Document remain LED blinks
at the cycle of 2000msec.
Resist/timing sensor
adjustment error (when power
is supplied)
Document remain LED blinks
at the cycle of 100msec.
Paper exit sensor adjustment
error (when power is supplied)
Ready LED blinks at the cycle
of 100msec.
A JAM/motor lock error can be canceled by opening/closing the ADF
after jam recovery process or by applying the power again. 
AR-405
7 – 27
1/21/1999
17) Reverse motor speed reduction 867 
→
 297mm/s (Paper exit
speed reduction)
18) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
19) Document feed LED ON, Document remain LED ON, Reverse
motor forward rotation 867mm/s (Paper exit operation)
20) Reverse motor speed reduction 867 
→
 297mm/s (Paper exit
speed reduction)
21) Document feed LED OFF, Document remain LED OFF, Reverse
motor OFF
Kind of JAM, error
LED display
Paper feed motor lock
error
REMOVE ORIGINAL LED blinks at
the cycle of 2000msec.
Return to 1).
f. EEPROM initializing + all sensors adjustment mode
When the DIP switch is set (3, 5 to ON, 1, 2, 4 to OFF) the push
switch is pressed, the EEPROM is initialized. At that time, the LED
blinks at the cycle of 100msec.
After completion of EEPROM initializing, the LED turns ON. In case of
an error in the EEPROM initializing, the LED blinks at the cycle of
2000msec.
Then all sensors adjustment is started. At that time, the document
remain LED blinks at the cycle of 100msec. After completion of all
sensors adjustment, the document remain LED turns ON. In case of
an. Error in the all sensors adjustment, the document remain LED
blinks at the cycle of 2000msec.
*
Only when the EEPROM is successfully completed, the all sensors
adjustment is performed. 
Kinds of JAM, error
LED display
EEPROM initializing
error
Ready LED blinks at the cycle of
2000msec.
All sensors adjustment
error
Document remain LED blinks at the
cycle of 2000msec
g. Resist sensor adjustment mode 
Set the DIP switch (4, 5 to ON, 1, 2, 3 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.  
After completion of the sensor adjustment, the LED turns ON. In case of
an error in the sensor adjustment, the LED blinks at the cycle of 100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
h. Timing sensor adjustment mode 
Set the DIP switch (1, 4, 5 to ON, 2, 3 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.  
After completion of the sensor adjustment, the LED turns ON. In case
of an error in the sensor adjustment, the LED blinks at the cycle of
100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
i. Paper exit sensor adjustment mode
Set the DIP switch (3, 4, 5 to ON, 1, 2 to OFF) and press the push
switch. Each sensor adjustment is performed. At that time, the LED
blinks at the cycle of 100msec.
After completion of the sensor adjustment, the LED turns ON. In case
of an error in the sensor adjustment, the LED blinks at the cycle of
100msec.
Kinds of JAM, error
LED display
Sensor adjustment
upper limit error
Document remain LED turns OFF.
Ready LED blinks at the cycle of
100msec.
Sensor adjustment
lower limit error
Document remain LED blinks at the
cycle of 100msec.
Ready LED turns OFF
*
This mode can be adjusted with SIM 53-2.
(4) Kinds of error (RADF single mode only)
Kinds of JAM, error
LED display
Not-reaching/remaining JAM in
the paper feed section
Document remain LED blinks
at the cycle of 1000msec.
Not-reaching/remaining JAM in
the paper exit section
Ready LED blinks at the cycle
of 1000msec.
Paper feed motor lock error
Document remain LED blinks
at the cycle of 2000msec.
Resist/timing sensor
adjustment error (when power
is supplied)
Document remain LED blinks
at the cycle of 100msec.
Paper exit sensor adjustment
error (when power is supplied)
Ready LED blinks at the cycle
of 100msec.
A JAM/motor lock error can be canceled by opening/closing the ADF
after jam recovery process or by applying the power again. 
AR-405
7 – 27
1/21/1999
Page of 18
Display

Sharp AR-405 (serv.man9) Service Manual ▷ Download

Found More:

AR-405 (serv.man9) Service Manuals

Preview DownloadPagesSize
AR-405 (serv.man3) AR405-Circuit Diagrams Service Manual 28 14.14 MB
AR-405 (serv.man4) AR405 Service Manual-General Service Manual 7 217.75 KB
AR-405 (serv.man5) AR405 Service Manual-Specifications Service Manual 6 66.04 KB
AR-405 (serv.man6) AR405 Service Manual-Options Service Manual 5 56.78 KB
AR-405 (serv.man7) AR405-Service Manual-Consumable Parts Service Manual 7 67.77 KB
AR-405 (serv.man8) AR405 Service Manual-External View and Internal Structure Service Manual 9 389.07 KB
AR-405 (serv.man10) AR405 Service Manual-Simulation Codes Service Manual 85 924.36 KB
AR-405 (serv.man11) AR405 Service Manual-Maintenance Service Manual 28 3.93 MB
AR-405 (serv.man12) AR405 Service Manual-Disassembly and Assembly Service Manual 12 1.28 MB
AR-405 (serv.man13) AR405 Service Manual-Trouble Code List Service Manual 12 79.48 KB
AR-405 (serv.man30) AR405 Operation Manual-Section 1 User Manual / Operation Manual 34 695.89 KB
AR-405 (serv.man31) AR405 Operation Manual-Section 2 User Manual / Operation Manual 64 1.52 MB
AR-405 (serv.man32) AR405 Operation Manual-Section 3 User Manual / Operation Manual 80 1.33 MB
AR-405 (serv.man14) Information of parts change Service Manual / Parts Guide 2 28.25 KB
AR-405 (serv.man15) Parts Guide AR250 280 285 287 335 337 405 407 505 507 Service Manual / Parts Guide 127 5.15 MB
AR-405 (serv.man16) AR405 Parts Guide-Exteriors Operation Panel Unit Document Size Sensor Unit Service Manual / Parts Guide 5 416.79 KB
AR-405 (serv.man17) AR405 Parts Guide-Optical Unit 1 Optical Unit 2 Service Manual / Parts Guide 5 598.66 KB
AR-405 (serv.man18) AR405 Parts Guide-Copy Lamp Unit 2nd,3rd Mirror Holder Unit Service Manual / Parts Guide 3 223.15 KB
AR-405 (serv.man19) AR405 Parts Guide-Frame Section Rear Frame 1 Rear Frame 2 Photo Conductor Unit Service Manual / Parts Guide 7 1.21 MB
AR-405 (serv.man20) AR405 Parts Guide-Toner Hopper Unit Developer Unit Fusing Unit 1 Fusing Unit 2 Service Manual / Parts Guide 9 728 KB
AR-405 (serv.man21) AR405 Parts Guide-1 Bin Delivery Turnover Unit 1 1 Bin Delivery Turnover Unit 2 Vertical Transport Right Door Unit Vertical Transport Unit Service Manual / Parts Guide 7 802.99 KB
AR-405 (serv.man22) AR405 Parts Guide-PS Transport Unit Suction Unit Main Drive Unit 1 Main Drive Unit 2 Paper Feeding Drive Unit 1 Paper Feeding Drive Unit 2 Service Manual / Parts Guide 8 1.06 MB
AR-405 (serv.man23) AR405 Parts Guide-DV Drive Unit Fusing Drive Unit DV Guide Unit Multi Manual Paper Feeding Unit 1 Multi Manual Paper Feeding Unit 2 Service Manual / Parts Guide 6 541.32 KB
AR-405 (serv.man24) AR405 Parts Guide-Waste Toner Unit Tray Paper Feeding Unit Multi Manual Paper Feeding Tray Unit MC Unit TC Unit Tray Unit Service Manual / Parts Guide 7 779.02 KB
AR-405 (serv.man25) AR405 Parts Guide-Packing Material Accessories PCU PWB ICU PWB Operation Control PWB Operation PWB R Operation PWB L Inverter PWB AC PWB Service Manual / Parts Guide 9 247.51 KB
AR-405 (serv.man26) AR405 Parts Guide-Scanner Drive PWB ORS PD PWB DC Power Supply PWB.100v DC Power Supply PWB.200v Service Manual / Parts Guide 7 137.31 KB
AR-405 (serv.man27) AR405 Parts Guide-RADF Exteriors RADF Transport Belt Section RADF Paper Feeding Transport Section 1 Service Manual / Parts Guide 7 923.97 KB
AR-405 (serv.man28) AR405 Parts Guide-RADF Paper Feeding Transport Section2 RADF Reversion Transport Section Paper Feeding Tray Section RADF PBA-Control PWB Service Manual / Parts Guide 8 764.96 KB
AR-405 (serv.man29) AR405 Parts Guide-Index Service Manual / Parts Guide 18 287.39 KB
AR-405 (serv.man2) AR405 Specifications Service Manual / Specification 6 218.37 KB
AR-405 (serv.man41) Change of Fuser Cover Part Number. Service Manual / Technical Bulletin 1 25.47 KB
AR-405 (serv.man42) Improvement made to prevent fire hazard caused by imperfect contact on fixing junction PWB. Service Manual / Technical Bulletin 1 45.23 KB
AR-405 (serv.man43) Re issue bulletin regarding a parts change - mainly for the mirror mount fixing plate. Service Manual / Technical Bulletin 4 1.6 MB
AR-405 (serv.man44) Change to the paper feed roller material. Service Manual / Technical Bulletin 13 1.22 MB
AR-405 (serv.man45) IMPROVEMENT MADE TO PREVENT MALFUNCTION CAUSED BY IMPERFECT CONTACT ON FIXING JUNCTION PWB. Service Manual / Technical Bulletin 1 106.72 KB
AR-405 (serv.man46) Reduction of F2-00 error. (Toner supply error) Service Manual / Technical Bulletin 2 12.33 KB
AR-405 (serv.man47) New service part for repairing a broken ADU frame Service Manual / Technical Bulletin 2 239.04 KB
AR-405 (serv.man48) Paper feed drive unit part change Service Manual / Technical Bulletin 1 30.01 KB
AR-405 (serv.man49) Corrections carried out in the parts guide (DV unit toner hopper) Service Manual / Technical Bulletin 2 91.78 KB
AR-405 (serv.man50) HV protect sheet addition Service Manual / Technical Bulletin 1 36.21 KB
AR-405 (serv.man51) Corrections made to a jamming error caused by the ADU transfer clutch dragging or slipping Service Manual / Technical Bulletin 1 42.95 KB
AR-405 (serv.man52) Establishment of the paper feeding drive clutch with mylar shehed as a service part Service Manual / Technical Bulletin 1 30.63 KB
AR-405 (serv.man53) Parts change information Service Manual / Technical Bulletin 1 30.59 KB
AR-405 (serv.man54) Notice of jam codes Service Manual / Technical Bulletin 3 58.33 KB
AR-405 (serv.man55) Supply of silicon oil used for cleaning the SPF glass to be carried out as a service part Service Manual / Technical Bulletin 1 30.82 KB
AR-405 (serv.man56) Copy paper jams caused by grease entering the internal section of the paper feeding drive clutch and supply of Hanari grease as a service part Service Manual / Technical Bulletin 1 34.59 KB
AR-405 (serv.man57) Corrections carried out in the parts guide Service Manual / Technical Bulletin 1 30.08 KB
AR-405 (serv.man58) Change carried out in the material of the reversion gate Service Manual / Technical Bulletin 1 29.82 KB
AR-405 (serv.man59) Establishent of the CG reverse roller shaft UN and the Reverse roller shaft UN in the 550 paper feeding unit as service parts Service Manual / Technical Bulletin 2 52.22 KB
AR-405 (serv.man60) Parts change information Service Manual / Technical Bulletin 4 140.64 KB
AR-405 (serv.man61) Correction carried out in the parts guide for the charger wire Service Manual / Technical Bulletin 1 19.22 KB
AR-405 (serv.man62) Part changes Service Manual / Technical Bulletin 1 33.26 KB
AR-405 (serv.man63) Improvement of paper jam udulation caused by hardening of the delivery roller Service Manual / Technical Bulletin 1 22.14 KB
AR-405 (serv.man64) Notice of jam cause codes Service Manual / Technical Bulletin 3 153.47 KB
AR-405 (serv.man65) Providing a caution label, as a service part, on adding toner Service Manual / Technical Bulletin 2 70.58 KB
AR-405 (serv.man66) Using the same hand-feed pick-up roller as the 550 paper-feeding unit Service Manual / Technical Bulletin 1 29.8 KB
AR-405 (serv.man67) Change of the cleaning blade Service Manual / Technical Bulletin 1 34.61 KB
AR-405 (serv.man68) Parts change information Service Manual / Technical Bulletin 1 30.89 KB
AR-405 (serv.man69) Parts change information Service Manual / Technical Bulletin 3 139.49 KB
AR-405 (serv.man70) Polygon motors for laser units. Service Manual / Technical Bulletin 1 20.68 KB
AR-405 (serv.man71) Change of pulley fixing double-thread screw and discontinued M4 tap. Service Manual / Technical Bulletin 1 85.91 KB
AR-405 (serv.man72) Change carried out in the hopper seal of the developing tank. Service Manual / Technical Bulletin 6 213.68 KB
AR-405 (serv.man73) Change of parts used in 550 paper feeding unit. Service Manual / Technical Bulletin 2 123.9 KB
AR-405 (serv.man74) Problem with main drive unit paper feed clutch. Service Manual / Technical Bulletin 3 1.18 MB
AR-405 (serv.man75) Addition of explanatory label for lever operation and change of suction lift shaft. Service Manual / Technical Bulletin 1 120.75 KB
AR-405 (serv.man76) Measure to alleviate problems of disengagement of the side plate in the machine cassette unit. Service Manual / Technical Bulletin 2 124.61 KB
AR-405 (serv.man77) ICU PWB part number change. Service Manual / Technical Bulletin 1 74.42 KB
AR-405 (serv.man78) Action to alleviate problems of static electricity through the use of a plastic bag for the machine. Service Manual / Technical Bulletin 1 72.63 KB
AR-405 (serv.man79) Abnormal noise from process unit. Service Manual / Technical Bulletin 1 60.53 KB
AR-405 (serv.man80) Part change information. Service Manual / Technical Bulletin 2 160 KB
AR-405 (serv.man81) Unification of 200V series DC power unit. (WHITE) Service Manual / Technical Bulletin 2 91.96 KB
AR-405 (serv.man82) Change of supplier for sintered bearings. (WHITE) Service Manual / Technical Bulletin 4 188.55 KB
AR-405 (serv.man83) Change of touch panel. (WHITE) Service Manual / Technical Bulletin 1 86.85 KB
AR-405 (serv.man84) Changes to the AR505 Service Manual and addition of jam cause codes. (WHITE) Service Manual / Technical Bulletin 5 323.55 KB
AR-405 (serv.man85) Change carried out in the original document detection photo sensor. (WHITE) Service Manual / Technical Bulletin 1 73.94 KB
AR-405 (serv.man86) Change carried out in the paper feeding drive frame and the transport clutch. (WHITE) Service Manual / Technical Bulletin 2 119.36 KB
AR-405 (serv.man87) Change carried out in the PS front roller bearing. (WHITE) Service Manual / Technical Bulletin 1 83.44 KB
AR-405 (serv.man88) Change carried out in the waste toner drive gear in the main drive unit. (WHITE) Service Manual / Technical Bulletin 1 83.58 KB
AR-405 (serv.man89) Measure to alleviate problems of snagging the copy keys on the operation panel. (YELLOW) Service Manual / Technical Bulletin 1 61.14 KB
AR-405 (serv.man90) Change carried out in the maker of the table glass used in the RADF. (WHITE) Service Manual / Technical Bulletin 2 116.81 KB
AR-405 (serv.man91) Action to alleviate problems of dislocation of the disfunction arm in the ADU unit. (WHITE) Service Manual / Technical Bulletin 1 83.85 KB
AR-405 (serv.man92) Change carried out in the location of production of the LSU unit. (WHITE) Service Manual / Technical Bulletin 1 88.01 KB
AR-405 (serv.man93) Discontinuance of the adjustment plate in the CCD unit. (WHITE) Service Manual / Technical Bulletin 1 133.8 KB
AR-405 (serv.man94) Countermeasure against Z-folding and paper mis-feed. (WHITE) Service Manual / Technical Bulletin 4 552.17 KB
AR-405 (serv.man95) Change carried out in the attachment screws for the operation panel LCD. (WHITE) Service Manual / Technical Bulletin 1 136.4 KB
AR-405 (serv.man96) Measure to improve the performance of the copy lamp. (WHITE) Service Manual / Technical Bulletin 1 114.6 KB
AR-405 (serv.man97) Change carried out in the shape of the bushing and the attachment gear in the paper-feeding drive unit. (WHITE) Service Manual / Technical Bulletin 2 137.66 KB
AR-405 (serv.man98) Change in shape of the TC holder R. (WHITE) Service Manual / Technical Bulletin 1 121.34 KB
AR-405 (serv.man99) Discontinuance of the adjustment plate in the CCD unit. (WHITE) Service Manual / Technical Bulletin 1 139.91 KB
AR-405 (serv.man100) Report of flash memory version method. (WHITE) Service Manual / Technical Bulletin 3 130.58 KB
AR-405 (serv.man101) Marks on the rear frame of copies, ghosting on the rear frame of copies. (WHITE) Service Manual / Technical Bulletin 1 89.71 KB
AR-405 (serv.man102) Fixing ARPB2 F9 00 error messages. (WHITE) Service Manual / Technical Bulletin 2 96.34 KB
AR-405 (serv.man103) Corrections to the Service Manual. (WHITE) Service Manual / Technical Bulletin 3 181.37 KB
AR-405 (serv.man104) Change carried out in the synchronous detection PWB in the LSU. (WHITE) Service Manual / Technical Bulletin 1 95.19 KB
AR-405 (serv.man105) 1.Change carried out in the stir plate of the developing tank unit. 2.Change carried out in the material used for the TX sheet in the toner hopper unit. (WHITE) Service Manual / Technical Bulletin 3 156.25 KB
AR-405 (serv.man106) Change Of Parts To Diminish The Noise From The Polygon Motor. (WHITE) Service Manual / Technical Bulletin 1 38.82 KB
AR-405 (serv.man107) 1.Change Carried Out In The Plastic Slider Washer In The ADU Unit. 2.Action To Alleviate Problems Of Static Electricity In The OP Control PWB Unit. (WHITE) Service Manual / Technical Bulletin 2 157.93 KB
AR-405 (serv.man108) Report Of Flash Memory Version Method. (WHITE) Service Manual / Technical Bulletin 2 127.96 KB
AR-405 (serv.man109) 1.Correction Of Screws In The Scanner Unit. 2.Addition Carried Out Of A Harness Protect Sheet S. (WHITE) Service Manual / Technical Bulletin 2 161.5 KB
AR-405 (serv.man110) ROM Version Upgrade (Control No.7). (WHITE) Service Manual / Technical Bulletin 1 58.4 KB
AR-405 (serv.man111) Length Change Of SP Tube. (WHITE) Service Manual / Technical Bulletin 1 63.22 KB
AR-405 (serv.man112) 1.Change Of The ICU PWB Unit At EFI's Request. 2.Change Of The Touch Panel Manufacturer. 3.Change Of The Heat-resistant Clamp Fixing Screws In The Fusing Unit. 4.Change Of The Action Time Changing The ICU PWB Memory To SDRAM. (WHITE) Service Manual / Technical Bulletin 3 87.22 KB
AR-405 (serv.man113) Extension Of The Rib On The Rail Section Of The 550-Tray Case. (WHITE) Service Manual / Technical Bulletin 2 90.29 KB
AR-405 (serv.man114) Corrections Carried Out In The Parts Guide. (WHITE) Service Manual / Technical Bulletin 7 292.04 KB
AR-405 (serv.man115) 1.Increase Of The DC Power Supply Capacity. 2.Change Of The Memory On the ICU PWB To SDRAM. 3.Change Of The Installation Procedure Manual And Addition Of Wire Saddle. (WHITE) Service Manual / Technical Bulletin 2 109.26 KB
AR-405 (serv.man116) 1.Satisfaction Of The Argentine Safety Standard. 2.Increase Of Strength Of The Boss On The Right End Of The RSPF Base. 3.Removal Of The RSPF Upper Guide Plate Holes And Addition Of The Delivery Paper Guide Positioner. (WHITE) Service Manual / Technical Bulletin 2 100.29 KB
AR-405 (serv.man117) 1.Points Of Caution To Be Observed During Maintenance Operations Of The Fusing Unit. 2.ROM Writer Functions For The ICU PWB. (WHITE) Service Manual / Technical Bulletin 2 77.3 KB
AR-405 (serv.man118) Change Carried Out In The Hard Disk. (WHITE) Service Manual / Technical Bulletin 2 116.42 KB
AR-405 (serv.man119) 1.Change Carried Out In The Main Harness. 2.Change Carried Out In The Spring Of The Multi Manual Unit. (WHITE) Service Manual / Technical Bulletin 2 78.44 KB
AR-405 (serv.man120) 1.Change Carried Out In The Bearings In The Paper Feeding Drive Unit. 2.Discontinuance Of The Manual Pressure Spring Attachment Plate. (WHITE) Service Manual / Technical Bulletin 2 79.01 KB
AR-405 (serv.man121) Change Carried Out In The Shape Of The AC Harness Cover. (WHITE) Service Manual / Technical Bulletin 2 76.14 KB
AR-405 (serv.man122) Report Of Flash Memory Version Method. (WHITE) Service Manual / Technical Bulletin 8 330.52 KB
AR-405 (serv.man123) Report Of Flash Memory Version Method. (WHITE) Service Manual / Technical Bulletin 6 133.49 KB
AR-405 (serv.man124) 1.Change To The Attachment Screws Of The Optical Reception PWB Holder. 2.Measure To Alleviate Problems Of Electrical Noise In The ICU PWB. (WHITE) Service Manual / Technical Bulletin 2 110.67 KB
AR-405 (serv.man125) 1.Parts Change To Incorporate Parts Manufactured By Sharp Into Assembled Units (Productivity Improvement). 2.Measure To Establish Uniformity Of The High Voltage PWB (To Improve Productivity). 3.Parts Change Carried Out In Accordance With A Change To In-house Production Of The LSU Unit. 4.Measure To Establish Uniformity Of The PCU PWB To Improve Productivity. 5.Measure To Alleviate Problems Of Scattering Of The Waste Toner. (WHITE) Service Manual / Technical Bulletin 1 69.79 KB
AR-405 (serv.man126) Change In The Magnetic Clutch Of The Paper Feeding Unit In The 500 Tray To Improve Productivity. (WHITE) Service Manual / Technical Bulletin 2 103.1 KB
AR-405 (serv.man127) 1.Change In The Height Of The ADU Opening And Closing PG Boss. 2.Change In The PG Quantity Of The Paper Feeding Desk. (WHITE) Service Manual / Technical Bulletin 4 164.31 KB
AR-405 (serv.man128) Correction Measure Carried Out To Allevaite Problems Of Diagonal Feeding Which Occurred During Copy Operations Using The ADF. (WHITE) Service Manual / Technical Bulletin 1 66.21 KB
AR-405 (serv.man129) Measure To Alleviate Problems Of Improperly Tightened Screws In The Paper Delivery Reversion Unit. (YELLOW) Service Manual / Technical Bulletin 1 59.72 KB
AR-405 (serv.man130) 1.Action Carried Out As A Measure To Improve The Precision Of The Diameter Of The PS Roller. 2.Addition Of An Edge Guide Sheet. 3.Addition Of A Caution Label Concerning The Laser In The LSU Unit. (WHITE) Service Manual / Technical Bulletin 3 84.29 KB
AR-405 (serv.man131) 1.Change Carried Out In The Assembly Contractor Of The Toner Hopper And Developing Unit. 2.Measure Carried Out To Protect The Main Developing Unit. 3.Measure To Improve The Alignment Performance Of The Waste Toner Transport Gear. 4.Measure To Diminish Abnormal Noise Which Occurs In The Paper Delivery Reversion No. 2 Bin Unit. (WHITE) Service Manual / Technical Bulletin 5 136.81 KB
AR-405 (serv.man132) Report Of Flash Memory Version Method. (WHITE) Service Manual / Technical Bulletin 6 107.72 KB
AR-405 (serv.man133) Fast Facts 96-Firmware upgrade for AR405 Service Manual / Technical Bulletin 1 6.51 KB
AR-405 (serv.man134) 1.Change In The Shape Of The Attachment Plate Of The AC PWB (To Improve Productivity). 2.In-house Production Of the Operation Manuals (To Improve Productivity). (WHITE) Service Manual / Technical Bulletin 2 45.13 KB
AR-405 (serv.man135) 1.Discontinuance Of The Plastic Sliders Used In The Developing Unit (To Improve Productivity). 2.Establishment Of Uniformity Of The Upper Cabinet Rear (To Improve Productivity). 3.Change In The Maker Of The Drive Unit Clutch (To Improve Productivity). 4.Discontinuance Of The Boss In The Fusing Unit (To Improve Productivity). (WHITE) Service Manual / Technical Bulletin 3 53.91 KB
AR-405 (serv.man136) AR405 335 285 280 and AR-DU1, Frame strengthening. Previously sent out as Fast Fact 94 Service Manual / Technical Bulletin 1 6.28 KB
AR-405 (serv.man36) ASPI Update and Check Utility Driver / Update 1.94 MB
AR-405 (serv.man37) Flash 5.1 Download Utility Driver / Update 16.94 KB
AR-405 (serv.man38) AR405 PCU Firmware 2.07 Driver / Update 796.07 KB
AR-405 (serv.man39) AR405 ICU Firmware 2.12 Driver / Update 979.15 KB
AR-405 (serv.man40) AR405 OPE Firmware 2.06 Driver / Update 1.27 MB
AR-405 Cougar Handy Guide (Updated March'02) Handy Guide 54 218.68 KB
AR-405 (serv.man33) Service Exchange Scheme Request Form (TP ServiceCo) FAQ 1 7.68 KB
AR-405 (serv.man34) Cougar Firmware Revision Table FAQ 6 19.71 KB
AR-405 (serv.man35) AR280 285 335 405 Jam Map Listing FAQ 2 5.3 KB
AR-405 (serv.man137) MSDS F-00871 Regulatory Data 2 194.68 KB
AR-405 (serv.man138) MSDS F-00881 Regulatory Data 2 195.14 KB
AR-405 (serv.man139) Environmental Data Sheet Regulatory Data 1 5.76 KB
AR-405 (serv.man140) MSDS F-30881 Regulatory Data 2 178 KB
AR-405 (serv.man141) MSDS F-30871 Regulatory Data 2 180.8 KB

RANDOM: