Sharp AR-205 (serv.man26) User Manual / Operation Manual ▷ View online
27
MAKING COPIES
1
Press the AUTO/MANUAL/PHOTO key to select the
PHOTO mode.
PHOTO mode.
2
Press and hold down the AUTO/MANUAL/PHOTO key
for approximately 5 seconds.
for approximately 5 seconds.
●
The PHOTO indicator will go out and the AUTO indicator will begin
to blink.
to blink.
●
One or two exposure indicators corresponding to the current automatic
exposure level will light up. The factory default setting is level “3”.
exposure level will light up. The factory default setting is level “3”.
3
Press the light (
) or dark(
) key to lighten or darken
the automatic exposure level as desired.
4
Press the AUTO/MANUAL/PHOTO key.
●
The AUTO indicator will stop blinking and will light up steadily.
●
This automatic exposure level will remain in effect until you change
it again by this procedure.
it again by this procedure.
Automatic exposure adjustment
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying needs.
This level is set for copying from the original table and copying from the
optional SPF or RSPF respectively. To set the level for the optional SPF or
RSPF, place an original in the document feeder tray and make sure that the
SPF indicator lights up before proceeding to step 1. To set the level for the
original table, ensure that the SPF indicator does not light up.
This level is set for copying from the original table and copying from the
optional SPF or RSPF respectively. To set the level for the optional SPF or
RSPF, place an original in the document feeder tray and make sure that the
SPF indicator lights up before proceeding to step 1. To set the level for the
original table, ensure that the SPF indicator does not light up.
28
ST
A
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.
and slide the cover out until it stops.
2
Push gently on both sides of the front cover to open the
cover.
cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
●
For
disposal
of
the
old
TD
cartridge,
contact
your
dealer.
4
Remove the new TD cartridge from the bag. Hold the
cartridge on both sides and shake it horizontally four or
five times.
cartridge on both sides and shake it horizontally four or
five times.
TD CARTRIDGE REPLACEMENT
If the machine detects an insufficient amount of toner available, it will stop
copying but will continue to run while feeding toner. During this time the TD
cartridge replacement required (
copying but will continue to run while feeding toner. During this time the TD
cartridge replacement required (
) indicator will blink and the START key
indicator will go out. When sufficient toner has been added, the blinking
indicator will go out and the START key indicator will light up indicating
that copying can be resumed. However, if toner addition continued for a
maximum of two minutes, the TD cartridge replacement required indicator
will light up steadily in addition to the START key indicator lighting. This
indicates that the toner supply is low and that a new TD cartridge will be
needed soon. If copying is continued in this state, the copies will gradually
become lighter until the copier stops and the TD cartridge replacement
required (
indicator will go out and the START key indicator will light up indicating
that copying can be resumed. However, if toner addition continued for a
maximum of two minutes, the TD cartridge replacement required indicator
will light up steadily in addition to the START key indicator lighting. This
indicates that the toner supply is low and that a new TD cartridge will be
needed soon. If copying is continued in this state, the copies will gradually
become lighter until the copier stops and the TD cartridge replacement
required (
) indicator begins to blink, indicating that the cartridge must be
replaced before copying can be resumed. Replace the TD cartridge by
following the procedure below.
following the procedure below.
For best copying results, be sure to use only
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
TD cartridge replacement
TD cartridge lock
release lever
release lever
4 or 5 times
GENUINE SUPPLIES
29
ST
A
A
TUS
INDICA
T
ORS
TD cartridge replacement
TD CARTRIDGE REPLACEMENT
5
Remove the protective cover from the TD cartridge by
unlatching three cover hooks from the holes on the
cartridge and then pulling the cover in the direction
indicated by the arrow in the illustration.
unlatching three cover hooks from the holes on the
cartridge and then pulling the cover in the direction
indicated by the arrow in the illustration.
6
Gently insert the TD cartridge along the guides until it
locks in place.
locks in place.
If dirt or dust is adhered to the TD cartridge, remove it
before installing the cartridge.
before installing the cartridge.
7
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover. The
hands and then close the side cover by pressing the
handle on the cover. The
indicator will go out.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
30
ST
A
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover
and slide the cover out until it stops.
and slide the cover out until it stops.
2
Push gently on both sides of the front cover to open the
cover.
cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
4
Grasp the handle of the drum cartridge and gently pull
the cartridge out.
the cartridge out.
●
For
disposal
of
the
old
drum
cartridge,
contact
your
dealer.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 30,000 copies. When
the internal counter reaches approximately 29,000 copies, the drum
replacement required (
the internal counter reaches approximately 29,000 copies, the drum
replacement required (
) indicator will light up indicating that replacement
of the drum cartridge will be needed soon. When the indicator begins to blink,
replace the drum cartridge by following the procedure given below.
replace the drum cartridge by following the procedure given below.
Do not remove the protective cover on the drum portion
(black paper) of a new drum cartridge before use. The
cover protects the drum against external light.
(black paper) of a new drum cartridge before use. The
cover protects the drum against external light.
●
For the procedure to find out how many more copies can be made before
the 30,000 mark is reached, see page 76, DRUM CARTRIDGE LIFE.
the 30,000 mark is reached, see page 76, DRUM CARTRIDGE LIFE.
Drum cartridge replacement
TD cartridge lock
release lever
release lever
For best copying results, be sure to use only
SHARP products.
The package of SHARP drum cartridge has the
Genuine Supplies label.
SHARP products.
The package of SHARP drum cartridge has the
Genuine Supplies label.
GENUINE SUPPLIES
Click on the first or last page to see other AR-205 (serv.man26) service manuals if exist.