Sharp AR-200 (serv.man9) User Manual / Operation Manual ▷ View online
11
GETTING ST
ARTED
Changing the copy paper size in the tray
1
Gently lift and pull out the paper tray until it stops.
2
Push the pressure plate down until it locks in place.
3
Squeeze the lock lever of the front guide and slide the
front guide to match the width of the paper.
front guide to match the width of the paper.
4
Move the left guide to the appropriate slot as marked
on the tray.
on the tray.
●
When using A5 copy paper, load it into the uppermost paper tray. If
other trays (including trays in optional paper feed units) are used,
paper misfeeds may occur.
other trays (including trays in optional paper feed units) are used,
paper misfeeds may occur.
5
Load copy paper into the tray.
6
Place the appropriate label to indicate the selected
paper size into the recess on the right front side of the
paper tray.
paper size into the recess on the right front side of the
paper tray.
7
Push the paper tray firmly back into the copier.
Loading copy paper
LOADING COPY PAPER
Front guide
Left guide
12
GETTING ST
ARTED
Loading copy paper
LOADING COPY PAPER
8
To set the selected paper size, press the PAPER SIZE
ENTER key.
ENTER key.
●
The selected paper feed location indicator will blink and the
corresponding paper size (which is currently set) indicator will light
up steadily. All other indicators will go out.
corresponding paper size (which is currently set) indicator will light
up steadily. All other indicators will go out.
For paper size setting, ensure that the COPY mode
has been selected. However, if copying, printing or
facsimile printing is being performed, paper size setting
cannot be made even in the COPY mode. See Note
on page 48.
has been selected. However, if copying, printing or
facsimile printing is being performed, paper size setting
cannot be made even in the COPY mode. See Note
on page 48.
9
Use the TRAY SELECT key to select the paper tray of
which the paper size has been changed.
which the paper size has been changed.
●
Each time the TRAY SELECT key is pressed, a paper tray will be
indicated with a blinking paper feed location indicator.
indicated with a blinking paper feed location indicator.
10
Use the ORIGINAL SIZE ENTER key to select the paper
size which is set.
size which is set.
●
Each time the ORIGINAL SIZE ENTER key is pressed, a paper size
will be indicated with a paper size indicator.
will be indicated with a paper size indicator.
11
Press the START key and then the PAPER SIZE ENTER
key.
key.
●
To change the paper size setting of another tray, repeat steps 9 to 10
after pressing the START key.
after pressing the START key.
13
MAKING COPIES
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not function
until an assigned 3-digit account number has been entered. See page 40 for
setting the auditing mode.
until an assigned 3-digit account number has been entered. See page 40 for
setting the auditing mode.
If the copier has been programmed in the auditing mode, “
– – –
” will appear
in the copy quantity display in the initial conditions.
1
Enter your account number using the numeric keys.
●
As each digit is entered, the dashes in the copy quantity display will
disappear.
disappear.
●
After the number is entered, the copy quantity display will change to
0.
0.
●
If an unassigned number is entered, “
– – –
” will appear again in the
copy quantity display, indicating that the number was not accepted.
2
When copying is completed, press the AUDIT CLEAR
key.
key.
●
“
– – –
” will appear again in the copy quantity display, indicating the
auditing mode.
●
In the interrupt copy mode (see page 25), press the INTERRUPT key
after an interrupt copy run is completed. All previous copier settings
will be restored and the previous account number will be active.
after an interrupt copy run is completed. All previous copier settings
will be restored and the previous account number will be active.
Auditing accounts
14
MAKING COPIES
NORMAL COPYING
1
Turn the power switch on.
●
It will take about 35 seconds for the copier to warm up. However, you
can make desired settings and press the START key during warm-up.
Copying will start after warm-up.
can make desired settings and press the START key during warm-up.
Copying will start after warm-up.
●
If the copier has been programmed in the auditing mode, the START
key indicator will not light up and “
key indicator will not light up and “
– – –
” will appear in the copy
quantity display. Enter an assigned 3-digit account number. See page
13.
13.
●
If the power is already on and all indicators except the POWER SAVE
indicator are off, the copier is in the auto power shut-off mode. Press
the START key in this case. See page 44, POWER SAVE MODES.
indicator are off, the copier is in the auto power shut-off mode. Press
the START key in this case. See page 44, POWER SAVE MODES.
2
Place the original face down on the original table. Align
it with the original size scale.
it with the original size scale.
●
The ORIGINAL SIZE indicator for the size detected will light up.
●
Image loss (max. 4 mm) can occur at the leading and trailing edges of
the copies. Also image loss (max. 4 mm in total) can occur along the
other edges of the copies.
the copies. Also image loss (max. 4 mm in total) can occur along the
other edges of the copies.
3
Close the platen cover.
●
Paper matching the size of the original will be automatically selected
when the auto paper select function is enabled. To copy onto paper of
a different size, press the TRAY SELECT key.
when the auto paper select function is enabled. To copy onto paper of
a different size, press the TRAY SELECT key.
●
The auto paper select function can be disabled using user program
No. 8. If this function is disabled, use the TRAY SELECT key to select
the desired paper tray. See page 37, USER PROGRAMS.
No. 8. If this function is disabled, use the TRAY SELECT key to select
the desired paper tray. See page 37, USER PROGRAMS.
●
The bypass tray cannot be automatically selected.
4
Ensure that the desired paper tray is selected.
5
Adjust the copy density.
●
This copier has three exposure modes to choose from — AUTOMATIC,
MANUAL, and PHOTO.
MANUAL, and PHOTO.
●
Automatic exposure is the standard initial setting for this copier. In this
mode, the characteristics of the original are “read” by the exposure
system and adjustments are automatically made. This optimizes the
contrast of the copied images by reducing the effect of coloured or
shaded background areas. See page 26 to adjust the automatic exposure
level.
mode, the characteristics of the original are “read” by the exposure
system and adjustments are automatically made. This optimizes the
contrast of the copied images by reducing the effect of coloured or
shaded background areas. See page 26 to adjust the automatic exposure
level.
Normal copying
Power on
Click on the first or last page to see other AR-200 (serv.man9) service manuals if exist.