Sharp AR-161 (serv.man21) User Manual / Operation Manual ▷ View online
27
ST
A
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover and
slide the cover out until it stops.
slide the cover out until it stops.
2
Push gently on both sides of the front cover to open the
cover.
cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
●
For
disposal
of
the
old
TD
cartridge,
contact
your
dealer.
4
Remove the new TD cartridge from the bag. Hold the
cartridge on both sides and shake it horizontally four or
five times.
cartridge on both sides and shake it horizontally four or
five times.
TD CARTRIDGE REPLACEMENT
If the machine detects an insufficient amount of toner being added,
copying will stop and the machine will add toner. During this time, the
START key indicator will blink. When sufficient toner has been added, the
indicator will go out indicating that copying can be resumed. However, if
toner addition continues for a maximum of two minutes, the TD cartridge
replacement required (
copying will stop and the machine will add toner. During this time, the
START key indicator will blink. When sufficient toner has been added, the
indicator will go out indicating that copying can be resumed. However, if
toner addition continues for a maximum of two minutes, the TD cartridge
replacement required (
) indicator will light up in addition to the START
key being lighted steadily. This indicates that the toner supply is low and
a new cartridge will be needed soon. If copying is continued, the copies
will gradually become lighter until the copier stops and the TD cartridge
replacement required indicator begins to blink, indicating that the cartridge
must be replaced. Replace the TD cartridge by following the procedure
below.
a new cartridge will be needed soon. If copying is continued, the copies
will gradually become lighter until the copier stops and the TD cartridge
replacement required indicator begins to blink, indicating that the cartridge
must be replaced. Replace the TD cartridge by following the procedure
below.
For best copying results, be sure to use only
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
SHARP products.
The package of SHARP toner has the Genuine
Supplies label.
TD cartridge replacement
TD cartridge lock
release lever
release lever
4 or 5 times
GENUINE SUPPLIES
28
ST
A
A
TUS
INDICA
T
ORS
TD cartridge replacement
TD CARTRIDGE REPLACEMENT
5
Remove the protective cover from the TD cartridge by
unlatching three cover hooks from the holes on the
cartridge and then pulling the cover in the direction
indicated by the arrow in the illustration.
unlatching three cover hooks from the holes on the
cartridge and then pulling the cover in the direction
indicated by the arrow in the illustration.
6
Gently insert the TD cartridge along the guides until it
locks in place.
locks in place.
If dirt or dust is adhered to the TD cartridge, remove it
before installing the cartridge.
before installing the cartridge.
7
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover. The
hands and then close the side cover by pressing the
handle on the cover. The
indicator will go out and the
START key indicator will light up.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
29
ST
A
A
TUS
INDICA
T
ORS
1
Open the bypass tray. Lift slightly on the side cover and
slide the cover out until it stops.
slide the cover out until it stops.
2
Push gently on both sides of the front cover to open the
cover.
cover.
3
Lift the TD cartridge lock release lever and pull the
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
cartridge out until the green strap handle can be grasped
by the right hand. Lift the cartridge by the handle while
supporting it with the left hand at the green label position
to remove it.
4
Grasp the handle of the drum cartridge and gently pull
the cartridge out.
the cartridge out.
●
For
disposal
of
the
old
drum
cartridge,
contact
your
dealer.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 30,000 copies. When
the internal counter reaches approximately 29,000 copies, the drum
replacement required (
the internal counter reaches approximately 29,000 copies, the drum
replacement required (
) indicator will light up indicating that replacement
of the drum cartridge will be needed soon. When the indicator begins to blink,
replace the drum cartridge by following the procedure given below.
replace the drum cartridge by following the procedure given below.
Do not remove the protective cover on the drum portion
(black paper) of a new drum cartridge before use. The
cover protects the drum against external light.
(black paper) of a new drum cartridge before use. The
cover protects the drum against external light.
●
For the procedure to find out how many more copies can be made before
the 30,000 mark is reached, see page 70, DRUM CARTRIDGE LIFE.
the 30,000 mark is reached, see page 70, DRUM CARTRIDGE LIFE.
Drum cartridge replacement
TD cartridge lock
release lever
release lever
For best copying results, be sure to use only
SHARP products.
The package of SHARP drum cartridge has the
Genuine Supplies label.
SHARP products.
The package of SHARP drum cartridge has the
Genuine Supplies label.
GENUINE SUPPLIES
30
ST
A
A
TUS
INDICA
T
ORS
DRUM CARTRIDGE REPLACEMENT
Drum cartridge replacement
5
Remove the new drum cartridge from the protective bag
and gently insert the lead end of the drum cartridge
along the guides.
and gently insert the lead end of the drum cartridge
along the guides.
Do not touch the surface of the drum (green portion) of
the cartridge. Doing so may cause smudges on the
copies.
the cartridge. Doing so may cause smudges on the
copies.
6
Remove the protective cover from the drum cartridge
and then push the cartridge all the way into the copier.
and then push the cartridge all the way into the copier.
7
Gently install the TD cartridge. To install the TD cartridge,
see page 27, TD CARTRIDGE REPLACEMENT.
see page 27, TD CARTRIDGE REPLACEMENT.
8
Close the front cover by pushing both sides with your
hands and then close the side cover by pressing the
handle on the cover. The drum replacement required
(
hands and then close the side cover by pressing the
handle on the cover. The drum replacement required
(
) indicator will go out and the START key indicator
will light up.
When closing the covers, be sure to close the front
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
cover securely and then close the side cover. If the
covers are closed in the wrong order, the covers may
be damaged.
Click on the first or last page to see other AR-161 (serv.man21) service manuals if exist.