Sharp AR-161 (serv.man21) User Manual / Operation Manual ▷ View online
7
GETTING ST
AR
TED
PART NAMES AND FUNCTIONS
Press and hold down the key.
12,345
sheets output
1st display
2nd display
Note: A3 size copies are counted as two copies.
@2
CLEAR key
Clears the copy quantity display or terminates a copy
run.
run.
@3
START key and indicator
Copying is possible when the indicator is on.
Press to start copying.
Press to start copying.
@4
CLEAR ALL (
) key
Clears all selected settings and returns the copier to the
initial settings.
initial settings.
@5
PRESET RATIO selector keys and indicators
(p. 17)
(p. 17)
Use to sequentially select preset reduction/enlargement
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200%.
copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%,
141%, 200%.
@6
ORIGINAL SIZE ENTER key and indicators
(p. 14, 16)
(p. 14, 16)
Use to input the original size for automatic paper selec-
tion and automatic copy ratio selection.
tion and automatic copy ratio selection.
@7
AUTO PAPER SELECT indicator
Paper of the proper size will be automatically selected
depending on the original size and selected copy ratio
when this indicator is on.
depending on the original size and selected copy ratio
when this indicator is on.
@8
TRAY SELECT key (p. 14)
Use to manually select a paper tray.
@9
AUTO IMAGE key and indicator
Press for automatic copy ratio selection.
#0
Paper feed location/misfeed location indica-
tors (p. 31)
tors (p. 31)
The selected paper feed location is shown by a lit
indicator (
indicator (
).
The general location of misfed paper is shown by a
blinking red indicator (
blinking red indicator (
).
#1
DUAL PAGE COPY key and indicator (p. 24)
Use to make individual copies of two originals placed
side by side on the original table.
side by side on the original table.
#2
ERASE key and indicators (p. 63)
Press to select the edge erase and/or the centre erase
mode. (Only available when an optional electronic
sorting kit is installed)
mode. (Only available when an optional electronic
sorting kit is installed)
#3
MARGIN SHIFT key and indicator (p. 65)
Shifts text or image on the copy to leave a binding
margin on the left side of the copy. (Only available
when an optional electronic sorting kit is installed)
margin on the left side of the copy. (Only available
when an optional electronic sorting kit is installed)
Initial settings
The copier assumes the initial settings when it is first turned
on, when the CLEAR ALL (
on, when the CLEAR ALL (
) key is pressed, and ap-
proximately one minute* after the last copy is made in any
mode.
mode.
●
Copy ratio: 100%
●
Exposure: Automatic
●
Copy quantity: 0
●
All special copier modes: Off
●
Auto paper selection : On
●
Paper feed station: Previously selected paper tray
* This time (auto clear time) can be changed. See page 36,
USER PROGRAMS.
Part names and functions
GETTING ST
AR
TED
GETTING ST
AR
TED
!7
!6
!5
!3
#1
#2
#3
!4
8
GETTING ST
AR
TED
Copier installation
COPIER INSTALLATION
Improper installation may damage the copier. Please note the following
during initial installation and whenever the copier is moved.
during initial installation and whenever the copier is moved.
If the copier is moved from a cool place to a warm place, condensation may form inside the copier.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room
temperature for at least 2 hours before use.
Do not install your copier in areas that are:
●
damp, humid, or very dusty
●
exposed to direct sunlight
●
poorly ventilated
●
subject to extreme temperature or humidity changes, e.g., near an
air conditioner or heater.
air conditioner or heater.
The copier should be installed near an accessible power outlet
for easy connection.
for easy connection.
Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
meets the specified voltage and current requirements.
Also make certain the outlet is properly grounded.
Connect the copier to a power outlet which is not used
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.
Be sure to allow the required space around the machine for
servicing and proper ventilation.
servicing and proper ventilation.
A small amount of ozone is produced within the copier during operation. The emission level is insufficient
to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 m
to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 m
g
/m
3
) calculated as
an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to
place the copier in a ventilated area.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to
place the copier in a ventilated area.
10 cm
9
GETTING ST
AR
TED
CAUTIONS ON HANDLING
Be careful in handling the copier as follows to maintain the performance of
this copier.
this copier.
Do not drop the copier, subject it to shock or strike it against any
object.
object.
Do not expose the drum cartridge to direct sunlight.
Doing so will damage the surface (green portion) of the drum cartridge,
causing poor copy quality.
Doing so will damage the surface (green portion) of the drum cartridge,
causing poor copy quality.
Store spare supplies such as drum cartridges and TD cartridges
in a dark place without removing from the package before use.
If they are exposed to direct sunlight, poor copies may result.
in a dark place without removing from the package before use.
If they are exposed to direct sunlight, poor copies may result.
Do not touch the surface (green portion) of the drum cartridge.
Doing so will damage the surface of the cartridge, causing smudges
on copies.
Doing so will damage the surface of the cartridge, causing smudges
on copies.
Cautions on handling
10
GETTING ST
AR
TED
LOADING COPY PAPER
To save space, this copier has been designed with an adjustable front-loading
tray, which is easily opened for paper loading. For best results, use only
SHARP recommended paper. (See page 49.)
The paper required (
tray, which is easily opened for paper loading. For best results, use only
SHARP recommended paper. (See page 49.)
The paper required (
) indicator will light up when there is no copy paper
in the selected paper feed station, or when the selected paper tray is not
installed or is improperly installed.
installed or is improperly installed.
When the paper size is changed in a paper tray, the size
of the paper must be entered by steps 8 through 11 on
page 12. If not, the edges of copies may become
smudged with toner. Also, the AUTO PAPER SELECT
and the AUTO IMAGE features will not function properly.
of the paper must be entered by steps 8 through 11 on
page 12. If not, the edges of copies may become
smudged with toner. Also, the AUTO PAPER SELECT
and the AUTO IMAGE features will not function properly.
1
Gently lift and pull out the paper tray until it stops.
2
Push the pressure plate down until it locks in place.
3
Fan the copy paper and insert it into the tray. Make sure
the edges go under the corner hooks.
the edges go under the corner hooks.
●
If you change to a different size of copy paper, the tray must be
adjusted. See the next page.
adjusted. See the next page.
●
Set the paper along the guides.
●
The tray holds up to 250 sheets of paper.
Do not load paper above the maximum height line.
Do not load paper above the maximum height line.
4
Push the paper tray firmly back into the copier.
Loading copy paper
Maximum height line
Click on the first or last page to see other AR-161 (serv.man21) service manuals if exist.