Sharp AR-161 (serv.man21) User Manual / Operation Manual ▷ View online
23
MAKING COPIES
B/W REVERSE
The B/W REVERSE feature is used to reverse black and white areas.
●
When the B/W REVERSE feature is selected, the exposure mode will be
automatically set to the MANUAL mode. Other exposure modes cannot
be selected.
Even if this feature is cancelled, the MANUAL mode will not
automatically be cancelled.
automatically set to the MANUAL mode. Other exposure modes cannot
be selected.
Even if this feature is cancelled, the MANUAL mode will not
automatically be cancelled.
1
Place the original on the original table and close the
platen cover.
platen cover.
2
Press the B/W REVERSE key.
3
Check the copy paper size.
●
If an optional paper feed unit is installed:
Use the ORIGINAL SIZE ENTER key to select the original size.
Copy paper of the same size as the original will be automatically
selected. If desired, another paper tray can be selected by pressing the
TRAY SELECT key.
Use the ORIGINAL SIZE ENTER key to select the original size.
Copy paper of the same size as the original will be automatically
selected. If desired, another paper tray can be selected by pressing the
TRAY SELECT key.
4
Make all other desired copier selections and press the
START key.
START key.
B/W reverse
Original
Copy
24
MAKING COPIES
1
Place the originals on the original table with the centre
of the two pages aligned with the paper size index
(
of the two pages aligned with the paper size index
(
A4). Close the platen cover.
●
Set the page to be copied first to the right of the paper size index mark.
2
Press the DUAL PAGE COPY key.
●
Check to be sure that the copy paper size in the paper tray is
A4.
A4.
3
Set the number of copies.
4
Press the START key.
DUAL PAGE COPY
The DUAL PAGE COPY feature produces individual copies of two docu-
ments placed side by side on the original table. It is especially useful when
copying books and other bound documents. This feature cannot be used with
the 2 in 1 or 4 in 1 feature and sort/group feature. (The 2 in 1 or 4 in 1 feature
and sort/group feature can only be used when an optional electronic sorting
kit and an optional SPF are installed.) If the AUTO IMAGE feature has been
selected, this feature cannot be selected.
To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the
DUAL PAGE COPY feature first and then the XY ZOOM feature.
(Enlargement cannot be set.)
ments placed side by side on the original table. It is especially useful when
copying books and other bound documents. This feature cannot be used with
the 2 in 1 or 4 in 1 feature and sort/group feature. (The 2 in 1 or 4 in 1 feature
and sort/group feature can only be used when an optional electronic sorting
kit and an optional SPF are installed.) If the AUTO IMAGE feature has been
selected, this feature cannot be selected.
To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the
DUAL PAGE COPY feature first and then the XY ZOOM feature.
(Enlargement cannot be set.)
Dual page copy
Original
Copy
25
MAKING COPIES
1
Press the INTERRUPT key.
●
The copier will return to the initial settings.
●
If this copier has been programmed in the auditing mode using user
program No. 10, “
program No. 10, “
–––
” will appear in the copy quantity display. Enter
your account number using the numeric keys. The number of copies
of the interrupt copying will be accumulated against this account
number. See page 13.
of the interrupt copying will be accumulated against this account
number. See page 13.
●
When an optional SPF is being used, the copier will stop after
completing the copying of the original which has been fed into the
SPF.
completing the copying of the original which has been fed into the
SPF.
2
When the copier stops, remove the original(s) and set
the original(s) for interrupt copying.
the original(s) for interrupt copying.
3
Select the desired available copier functions.
4
Set the number of copies.
5
Press the START key.
●
The interrupt copies will be offset from the previous copies when user
program No. 19 is enabled. (AR-161 only)
program No. 19 is enabled. (AR-161 only)
6
When all INTERRUPT copies are finished, press the
INTERRUPT key again to cancel the INTERRUPT mode,
and remove the original used for interrupt copying.
INTERRUPT key again to cancel the INTERRUPT mode,
and remove the original used for interrupt copying.
●
The previous copy quantity, copy ratio, copy density, and paper size
will be automatically restored.
will be automatically restored.
7
Replace the original(s) for the interrupted job on the
original table or in the SPF and press the START key.
original table or in the SPF and press the START key.
INTERRUPTING A COPY RUN
INTERRUPT is used to interrupt a long copy run so that another job can be
done.
done.
●
If sort or group copying is being performed, sort or group cannot be
selected during interrupt copying. (Sort and group can be performed only
if an optional electronic sorting kit and an optional SPF are installed.)
selected during interrupt copying. (Sort and group can be performed only
if an optional electronic sorting kit and an optional SPF are installed.)
Interrupting a copy run
26
MAKING COPIES
1
Press the AUTO/MANUAL/PHOTO key to select the
PHOTO mode.
PHOTO mode.
2
Press and hold down the AUTO/MANUAL/PHOTO key
for approximately 5 seconds.
for approximately 5 seconds.
●
The PHOTO indicator will go out and the AUTO indicator will begin
to blink.
to blink.
●
One or two exposure indicators corresponding to the current automatic
exposure level will light up. The factory default setting is level “3”.
exposure level will light up. The factory default setting is level “3”.
3
Press the light (
) or dark (
) key to lighten or darken
the automatic exposure level as desired.
4
Press the AUTO/MANUAL/PHOTO key.
●
The AUTO indicator will stop blinking and will light up steadily.
●
This automatic exposure level will remain in effect until you change
it again by this procedure.
it again by this procedure.
Automatic exposure adjustment
AUTOMATIC EXPOSURE ADJUSTMENT
The automatic exposure level can be adjusted to suit your copying needs.
This level is set for copying from the original table and copying from the
optional SPF respectively. To set the level for the optional SPF, place an
original in the SPF tray and make sure that the SPF indicator lights up
before proceeding to step 1. To set the level for the original table, ensure
that the SPF indicator does not light up.
This level is set for copying from the original table and copying from the
optional SPF respectively. To set the level for the optional SPF, place an
original in the SPF tray and make sure that the SPF indicator lights up
before proceeding to step 1. To set the level for the original table, ensure
that the SPF indicator does not light up.
Click on the first or last page to see other AR-161 (serv.man21) service manuals if exist.