Sharp AR-155 (serv.man23) User Manual / Operation Manual ▷ View online
31
5
Copier trouble?
MISFEED REMOVAL
●
Do not touch the surface of the drum (green portion) of the drum cartridge
when removing the misfed paper. Doing so may cause smudges on copies.
when removing the misfed paper. Doing so may cause smudges on copies.
●
Do not remove the misfed paper from above the fusing unit. Unfixed toner on
the paper may stain the paper transport area, resulting in smudges on copies.
the paper may stain the paper transport area, resulting in smudges on copies.
Raise the fusing unit release lever and then close the side cover by pressing the round
projections near the side cover open button. The misfeed (
projections near the side cover open button. The misfeed (
) indicator will go out and
the ready (
) indicator will light up.
C Misfeed in the transport area
Lower the fusing unit release lever by rotating it all the way as shown in the illustration.
Fusing unit release lever
Push gently on both sides of the front cover to open the cover.
While you are lowering the fusing unit release lever, it will not move smoothly at
a location on the way. However, be sure to lower the lever by rotating it all the
way to the location where it will not rotate as shown in the right illustration.
a location on the way. However, be sure to lower the lever by rotating it all the
way to the location where it will not rotate as shown in the right illustration.
32
5
Copier trouble?
Rotate the feeding roller in the direction of the arrow and gently remove the misfed
paper from the exit area.
paper from the exit area.
Feeding roller
Raise the fusing unit release lever, close the front cover and then close the side cover
by pressing the round projections near the side cover open button. The misfeed (
by pressing the round projections near the side cover open button. The misfeed (
)
indicator will go out and the ready (
) indicator will light up.
When closing the covers, be sure to close the front cover securely and then
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
close the side cover. If the covers are closed in the wrong order, the covers
may be damaged.
D Misfeed in the RSPF
An original misfeed may occur at one of three locations: if the misfed original is seen from the
document feeder tray, (A) in the document feeder tray; if the misfed original is not seen from
the document feeder tray, (B) in the exit area or (C) under the feeding roller. Remove the misfed
original following the instructions for each location.
document feeder tray, (A) in the document feeder tray; if the misfed original is not seen from
the document feeder tray, (B) in the exit area or (C) under the feeding roller. Remove the misfed
original following the instructions for each location.
(A)
Open the feeding roller cover and pull the original gently to the left and out from the
document feeder tray. Close the feeding roller cover. Open and close the original cover to
clear the RSPF misfeed ( ) indicator.
If the misfed original cannot be easily removed, proceed to (C).
document feeder tray. Close the feeding roller cover. Open and close the original cover to
clear the RSPF misfeed ( ) indicator.
If the misfed original cannot be easily removed, proceed to (C).
Feeding roller cover
(B)
Open the original cover and rotate the roller rotating knob to remove the misfed original
from the exit area.
If the misfed original cannot be easily removed, proceed to (C).
from the exit area.
If the misfed original cannot be easily removed, proceed to (C).
MISFEED REMOVAL
33
5
Copier trouble?
MISFEED REMOVAL
Roller rotating knob
With the RSPF, pull out the reversing tray to remove the misfed original.
With the RSPF, after removing the misfed original from the exit area, be sure to
insert the reversing tray into the exit area until it locks in place.
insert the reversing tray into the exit area until it locks in place.
(C) If the original does not move easily into the exit area remove it in the direction of the arrow
while rotating the knob.
A number may appear in the display after a minus sign, indicating the number
of the originals that must be returned to the document feeder tray.
Clear the misfeed and return the required number of originals. Then press the
print (
of the originals that must be returned to the document feeder tray.
Clear the misfeed and return the required number of originals. Then press the
print (
) key to resume copying.
34
5
Copier trouble?
MAINTENANCE REQUIRED
When
indicator lights up, service by an authorised SHARP service technician is required.
Contact your SHARP dealer as soon as possible.
Click on the first or last page to see other AR-155 (serv.man23) service manuals if exist.