Sharp AL-1566 (serv.man13) Service Manual ▷ View online
AL-1556/1566 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 9
22
12
Drum counter display
(DRUM CNT)
(DRUM CNT)
[Function]
The drum counter is displayed.
The drum counter is displayed.
[Operation]
14
ROM version display (ROM
VER.)
VER.)
[Function]
The P-ROM version is displayed.
Press [
The P-ROM version is displayed.
Press [
←
/
→
/10KEY] to switch the display version.
[Operation]
16
Duplex counter display
(DPLX CNT)
(DPLX CNT)
[Function]
The duplex counter is displayed.
The duplex counter is displayed.
[Operation]
17
Copy counter display
(COPIES CNT)
(COPIES CNT)
[Function]
The copy counter is displayed.
The copy counter is displayed.
[Operation]
18
Printer counter display
(PRT.CNT)
(PRT.CNT)
[Function]
The printer counter is displayed.
The printer counter is displayed.
[Operation]
19
Scanner mode counter
display (S-MODE CNT)
display (S-MODE CNT)
[Function]
The scanner mode counter is displayed.
The scanner mode counter is displayed.
[Operation]
21
Scanner counter display
(SCAN CNT)
(SCAN CNT)
[Function]
The scanner counter is displayed.
The scanner counter is displayed.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
22-12 DRUM CNT
***,***
Code number
Version
Display item
0
Main unit Program
MAIN PROG.
1
F-IMC Program
F-IMC PROG.
2
LCD DATA
LCD DATA
1) Initial display
2) [
→
/10KEY]
2) [
←
/10KEY]
22-14 ROM VER.
MAIN PROG. 00.00
22-14 ROM VER.
F-IMC PROG. 00.00
22-14 ROM VER.
LCD DATA 00.00
1) Initial display
22-16 DPLX CNT
***,***
1) Initial display
22-17 COPIES CNT
***,***
1) Initial display
22-18 PRT.CNT
***,***
1) Initial display
22-19 S-MODE CNT
***,***
1) Initial display
22-21 SCAN CNT
***,***
AL-1556/1566 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 10
22
22
SPF JAM counter display (S
JAM CNT)
JAM CNT)
[Function]
The SPF JAM counter is displayed.
The SPF JAM counter is displayed.
[Operation]
24
01
JAM total counter clear (JAM
TTL CLR.)
TTL CLR.)
[Function]
When [OK/START] key is pressed, the JAM total counter is cleared to 0 and "000,000" is displayed on
the LCD.
When [OK/START] key is pressed, the JAM total counter is cleared to 0 and "000,000" is displayed on
the LCD.
[Operation]
04
SPF counter clear (SPF
CLR.)
CLR.)
[Function]
When [OK/START] key is pressed, the SPF counter value is cleared to 0 and "000,000" is displayed
on the LCD.
When [OK/START] key is pressed, the SPF counter value is cleared to 0 and "000,000" is displayed
on the LCD.
[Operation]
05
Duplex counter clear (DPLX
CLR.)
CLR.)
[Function]
When [OK/START] key is pressed, the duplex counter value is cleared to 0, and "000,000" is dis-
played on the LCD.
When [OK/START] key is pressed, the duplex counter value is cleared to 0, and "000,000" is dis-
played on the LCD.
[Operation]
07
Drum counter clear (DRUM
CLR.)
CLR.)
[Function]
When [OK/START] key is pressed, the drum counter value is cleared to 0, and "000,000" is displayed
on the LCD.
When [OK/START] key is pressed, the drum counter value is cleared to 0, and "000,000" is displayed
on the LCD.
[Operation]
08
Copy counter clear (COPIES
CLR.)
CLR.)
[Function]
When [OK/START] key is pressed, the copy counter value is cleared to 0, and "000,000" is displayed
on the LCD.
When [OK/START] key is pressed, the copy counter value is cleared to 0, and "000,000" is displayed
on the LCD.
[Operation]
09
Printer counter clear
(PRT.CLR.)
(PRT.CLR.)
[Function]
When [OK/START] key is pressed, the printer counter value is cleared to 0, and "000,000" is dis-
played on the LCD.
When [OK/START] key is pressed, the printer counter value is cleared to 0, and "000,000" is dis-
played on the LCD.
[Operation]
10
FAX counter clear (FAX
CLR.) (AL-1566)
CLR.) (AL-1566)
[Function]
When PRINT switch is pressed, the FAX count value is set to 0 and "000,000" is displayed on the
LCD.
When PRINT switch is pressed, the FAX count value is set to 0 and "000,000" is displayed on the
LCD.
[Operation]
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
22-22 S JAM CNT
***,***
1) Initial display
24-01 JAM TTL CLR.
CLEARED 000,000
1) Initial display
24-04 SPF CLR.
CLEARED 000,000
1) Initial display
24-05 DPLX CLR.
CLEARED 000,000
1) Initial display
24-07 DRUM CLR.
CLEARED 000,000
1) Initial display
24-08 COPIES CLR.
CLEARED 000,000
1) Initial display
24-09 PRT.CLR.
CLEARED 000,000
1) Initial display
24-10 FAX CLR.
CLEARED 000,000
AL-1556/1566 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 11
24
13
Scanner counter clear
(SCAN CLR.)
(SCAN CLR.)
[Function]
When [OK/START] key is pressed, the scanner counter value is cleared to 0, and "000,000" is
displayed on the LCD.
When [OK/START] key is pressed, the scanner counter value is cleared to 0, and "000,000" is
displayed on the LCD.
[Operation]
14
SPF JAM total counter clear
(S JAM TTL CLR.)
(S JAM TTL CLR.)
[Function]
When [OK/START] key is pressed, the SPF JAM total counter value is cleared to 0, and "000,000" is
displayed on the LCD.
When [OK/START] key is pressed, the SPF JAM total counter value is cleared to 0, and "000,000" is
displayed on the LCD.
[Operation]
15
Scanner mode counter clear
(S-MODE CLR.)
(S-MODE CLR.)
[Function]
When [OK/START] key is pressed, the scanner mode counter value is cleared to 0, and "000,000" is
displayed on the LCD.
When [OK/START] key is pressed, the scanner mode counter value is cleared to 0, and "000,000" is
displayed on the LCD.
[Operation]
25
01
Main motor operation check
(MAIN MOTOR CHK)
(MAIN MOTOR CHK)
[Function]
When [OK/START] key is pressed, the main motor (and the duplex motor in the case of a duplex
model) is operated for 30sec.
When [OK/START] key is pressed, the main motor (and the duplex motor in the case of a duplex
model) is operated for 30sec.
To reduce toner consumption, if the developing unit is installed, the developing bias, the main
charger, and the grid are also outputted.
charger, and the grid are also outputted.
In this case, laser discharge is required when stopping the motor, the polygon motor is also operated
at the same time. Check for installation of the developing unit. If it is not installed, the high voltage
above is not outputted and only the motor is rotated.
at the same time. Check for installation of the developing unit. If it is not installed, the high voltage
above is not outputted and only the motor is rotated.
To check the developing bias, install the developing unit.
After completion of 30sec operation, the machine goes into the sub code entry standby mode.
[Operation]
10
Polygon motor operation
check (LSU CHK)
check (LSU CHK)
[Function]
When [OK/START] key is pressed, the Bios is called to rotate the polygon motor for 30sec.
After completion of 30sec operation, the operation is turned off with the Bios and the machine goes
into the sub code entry standby mode.
When [OK/START] key is pressed, the Bios is called to rotate the polygon motor for 30sec.
After completion of 30sec operation, the operation is turned off with the Bios and the machine goes
into the sub code entry standby mode.
[Operation]
26
02
(R)SPF setting (SPF/RSPF)
[Function]
When this test command is executed, the current set SPF is displayed. Enter the code number corre-
sponding to the desired SPF and press [OK/START] key to save the setting.
When this test command is executed, the current set SPF is displayed. Enter the code number corre-
sponding to the desired SPF and press [OK/START] key to save the setting.
[Operation]
The operation is similar to test command 21-01.
The operation is similar to test command 21-01.
Main
code
code
Sub
code
Contents
Details of function/operation
1) Initial display
24-13 SCAN CLR.
CLEARED 000,000
1) Initial display
24-14 S JAM TTL CLR.
CLEARED 000,000
1) Initial display
24-15 S-MODE CLR.
CLEARED 000,000
1) Initial display
25-01 MAIN MOTOR CHK
EXECUTING...
1) Initial display
25-10 LSU CHK
EXECUTING...
Code number
SPF
Display item
0
SPF NO
SPF OFF
1
SPF YES
SPF ON
2
RSPF YES
RSPF ON
AL-1556/1566 TEST COMMAND, FAX SOFT SWITCH, TROUBLE CODES 10 - 12
26
03
Second cassette setting
(2ND TRAY)
(2ND TRAY)
[Function]
When this test command is executed, the current set second cassette is displayed. Enter the code
number corresponding to the desired second cassette and press [OK/START] key to save the setting.
When this test command is executed, the current set second cassette is displayed. Enter the code
number corresponding to the desired second cassette and press [OK/START] key to save the setting.
[Operation]
The operation is similar to test command 21-01.
The operation is similar to test command 21-01.
04
Main unit duplex setting
(DPLX)
(DPLX)
[Function]
When this test command is executed, the current set duplex is displayed. Enter the code number cor-
responding to the desired duplex and press [OK/START] key to save the setting.
When this test command is executed, the current set duplex is displayed. Enter the code number cor-
responding to the desired duplex and press [OK/START] key to save the setting.
[Operation]
The operation is similar to test command 21-01.
The operation is similar to test command 21-01.
06
Destination setting
(DESTINATION)
(DESTINATION)
[Function]
When this test command is executed, the current set destination is displayed. Enter the code number
corresponding to the desired destination and press [OK/START] key to save the setting.
When this test command is executed, the current set destination is displayed. Enter the code number
corresponding to the desired destination and press [OK/START] key to save the setting.
∗
For Japan AB series, there is no schedule for production.
[Operation]
The operation is similar to test command 21-01.
The operation is similar to test command 21-01.
07
Machine conditions check
(CPM)
(CPM)
[Function]
When this test command is executed, the current machine setting is displayed.
When this test command is executed, the current machine setting is displayed.
[Operation]
20
Rear edge void setting (END
EDGE)
EDGE)
[Function]
When this test command is executed, the current set rear edge void is displayed. Enter the code num-
ber corresponding to the desired rear edge void and press [OK/START] key to save the setting.
When this test command is executed, the current set rear edge void is displayed. Enter the code num-
ber corresponding to the desired rear edge void and press [OK/START] key to save the setting.
[Operation]
The operation is similar to test command 21-01.
The operation is similar to test command 21-01.
30
CE mark support control ON/
OFF (CE MARK)
OFF (CE MARK)
[Function]
When this test command is executed, the current set CE mark support control is displayed. Enter the
code number corresponding to the desired CE mark support control and press [OK/START] key to
save the setting.
When this test command is executed, the current set CE mark support control is displayed. Enter the
code number corresponding to the desired CE mark support control and press [OK/START] key to
save the setting.
[Operation]
The operation is similar to test command 21-01.
The operation is similar to test command 21-01.
Main
code
code
Sub
code
Contents
Details of function/operation
Code number
Second cassette
Display item
0
Second cassette NO
OFF
1
Second cassette YES
ON
Code number
Duplex
Display item
0
Duplex NO
OFF
1
Duplex YES
ON
Code number
Destination
Display item
0
Inch series
INCH
1
EX Japan AB series
AB
2
Japan AB series
–
3
China (EX Japan AB series + China paper support)
CHINA
CPM
Coy quantity
Remark
10 CPM
10
12 CPM
12
13 CPM
13
14 CPM
14
15 CPM
15
16 CPM
16
1) The machine setting is displayed.
26-07 CPM
10 CPM
Code number
Setting
Display item
Remark
0
Rear edge void NO
OFF
1
Rear edge void YES
ON
Default
Code number
Setting
Display item
Remark
0
CE mark support control OFF
OFF
Default (100V series)
1
CE mark support control ON
ON
Click on the first or last page to see other AL-1566 (serv.man13) service manuals if exist.