Sharp PN-V601 (serv.man8) User Manual / Operation Manual ▷ View online
E
9
Menu item details
The menu will differ depending on the input mode.
n
SCREEN
AUTO (PC D-SUB/PC RGB)
The CLOCK, PHASE, H-POS, and V-POS are automatically
The CLOCK, PHASE, H-POS, and V-POS are automatically
adjusted.
Pressing
performs adjustment.
Use this automatic adjustment when you use the PC D-sub
input terminal or PC RGB input terminals to display a PC
screen for the first time or when you change the setting of
the PC. (See page 15.)
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
When using the adjustment pattern (see page 15), make
adjustments so that no vertical stripe noise appears in it.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.
Useful when small characters appear with low contrast and/
or there are flickers at corners.
When using the adjustment pattern (see page 15), make
adjustments so that no horizontal stripe noise appears in it.
* Adjustments to PHASE should be made only after CLOCK
has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of
input signals is not recognized properly. (Adjustment may be
impossible with some signals.)
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input
signals is not recognized properly. (Adjustment may be
impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory
RESET
Resets the values of the SCREEN menu items to the factory
preset values.
Select “ON” and then press
MENU
.
n
PICTURE
AUTO (PC D-SUB/PC RGB)
The CONTRAST and BLACK LEVEL are automatically
The CONTRAST and BLACK LEVEL are automatically
adjusted.
Pressing
performs adjustment.
CONTRAST
Adjusts the brightness of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards
Adjusts the brightness of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards
green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 15.)
COLOR MODE
Changes the color mode on the screen. The color mode on
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 15.)
COLOR MODE
Changes the color mode on the screen. The color mode on
the screen can also be changed using a remote control unit.
(See page 5.)
* sRGB is PC input only. See page 5 for details.
WHITE BALANCE
THRU .............. Displays the input signal level as is. (for PC
WHITE BALANCE
THRU .............. Displays the input signal level as is. (for PC
DVI-D/PC HDMI only)
PRESET ......... Selects the color temperature using PRESET.
USER .............. Used for adjusting R-/G-/B-CONTRAST and
R-/G-/B-OFFSET respectively.
PRESET
Selects the color temperature when the WHITE BALANCE is
Selects the color temperature when the WHITE BALANCE is
set to PRESET.
The setting values are shown for reference. The color
temperature of the screen varies over time.
This function is not intended to keep the color temperature
constant.
USER
Adjusts each item when the WHITE BALANCE is set to
USER
Adjusts each item when the WHITE BALANCE is set to
USER.
R-CONTRAST ....Adjusts bright-toned red component.
G-CONTRAST ....Adjusts bright-toned green component.
B-CONTRAST ....Adjusts bright-toned blue component.
R-OFFSET ..........Adjusts dark-toned red component.
G-OFFSET .........Adjusts dark-toned green component.
B-OFFSET ..........Adjusts dark-toned blue component.
COPY TO USER
Copies the value set for PRESET to the USER setting.
COPY TO USER
Copies the value set for PRESET to the USER setting.
Select “ON” and then press
MENU
.
GAMMA
Select a gamma value. USER sets the gamma value
Select a gamma value. USER sets the gamma value
transferred by the user. (See page 20.)
RESET
Resets the values of the PICTURE menu items to the factory
RESET
Resets the values of the PICTURE menu items to the factory
preset values.
Select “ON” and then press
MENU
.
Menu Items
E
10
n
AUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
Select “ON” and then press
MENU
.
n
SETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
MONITOR
Select the installation direction of the monitor.
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
MONITOR
Select the installation direction of the monitor.
LANDSCAPE ............Horizontal orientation
PORTRAIT ...............Vertical orientation
LANGUAGE
Sets the display language for the menu screen.
POWER ON DELAY
You can delay the screen display after the monitor is turned
LANGUAGE
Sets the display language for the menu screen.
POWER ON DELAY
You can delay the screen display after the monitor is turned
on. The period can be set up to 60 seconds in units of one
second. When this function is activated, the power LED
flashes (at approx. 1 second interval) in orange. This function
is disabled when 0 is specified.
OPERATION MODE
MODE1 ......Limits the maximum brightness lower than
OPERATION MODE
MODE1 ......Limits the maximum brightness lower than
MODE2.
OFF IF NO OPERATION is set to ON, and
STANDBY MODE is set to LOW POWER.
(These settings can not be changed.)
MODE2 ......Will perform standard operation.
OFF IF NO OPERATION is set to OFF, and
STANDBY MODE is set to STANDARD. These
settings can be changed.
STANDBY MODE
When STANDARD is selected, startup time from standby
When STANDARD is selected, startup time from standby
mode is reduced. Note, however that, more power will be
consumed in standby mode.
When LOW POWER is selected, current consumption
is reduced while the monitor is in standby mode. Note,
however, that the startup time from standby mode becomes
longer.
If set to LOW POWER, certain RS-232C commands cannot
be used in standby mode, and control via LAN will be
disabled.
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into
standby mode when there is no operation from the remote
control unit, RS-232C commands, or LAN for over 4 hours.
HDMI SETTING
HDMI AUTO VIEW
HDMI AUTO VIEW
......................... When ON is selected, the screen size is
adjusted automatically according to the
screen size control signal included in the
video signal input from the AV HDMI input
terminal.
HDMI RGB INPUT RANGE
......................... Sets the type of HDMI signals when using
the AV HDMI input mode.
When AUTO is selected, the type is set
automatically.
HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI
Sets whether to use hot plug control for the PC/AV HDMI
and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
RS-232C/LAN SELECT
Selects the method with which to control the monitor from
the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain
(see page 18), using the remote control unit or RS-232
cables.
The numbers 1 to 255 are available for ID numbers.
If “0” is set, the system regards this as the state where no ID
number is set.
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
AUTO ASSIGN ID No.
ID No. to be used will be automatically assigned when
multiple monitors are connected with RS-232C.
Select ON, then press
MENU
. Perform operations with the
primary monitor.
BAUD RATE
Selects the communication speed used for RS-232C
BAUD RATE
Selects the communication speed used for RS-232C
communication.
LAN SETUP
Configures the settings to control the monitor from the
LAN SETUP
Configures the settings to control the monitor from the
computer via LAN. (See page 28.)
BRIGHTNESS SENSOR
BRIGHTNESS SENSOR
(When connected to the PN-ZR01 only)
When set to ON or ON: DISPLAY, the brightness will
When set to ON or ON: DISPLAY, the brightness will
automatically change according to the lighting and
surrounding brightness. Performs operation with the primary
monitor. If set to ON: DISPLAY, the effect will be displayed
with a
with a
.
If connecting to multiple monitors, the brightness of all the
monitors will change.
The
The
will be displayed on the primary only.
BRIGHTNESS SENSOR SETTING
(When connected to the PN-ZR01 only)
Performs adjustments to the brightness sensor. Performs
Performs adjustments to the brightness sensor. Performs
operation with the primary monitor.
Set the surrounding brightness and the current screen
luminance to AMBIENT BRIGHTNESS and SCREEN
BRIGHTNESS.
Individually set WHEN LIGHT: and WHEN DARK:.
Even if brighter or darker than the set AMBIENT
BRIGHTNESS, the screen brightness will not change.
Current AMBIENT BRIGHTNESS is shown for reference.
Menu Items
E
11
Menu Items
AUDIO LEVEL(STEREO MINI)
Selects the maximum audio input level of the audio input
Selects the maximum audio input level of the audio input
terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to
perform screen adjustment automatically or not. When ON
is selected, the screen is automatically adjusted when its
resolution is 800 x 600 or higher and the timing of input
signals changes. “ADJUSTING” appears on the screen
during the adjustment. For images with black edges, etc.,
depending on the signal, adjustment may not be possible.
In this case select OFF. (Perform manual adjustment of the
screen.)
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is
selected and no signal is present in the selected input mode,
AUTO INPUT CHANGE automatically changes the selected
mode to another mode where a video signal is present.
When video signals exist in multiple input modes, the
switching priority is as follows:
PC D-SUB, PC HDMI and AV HDMI
When the PN-ZB02 (optional) is attached:
PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV
HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO
(Input mode switching may take 15 seconds or more,
depending on the connected equipment. Input signals
may not be detected properly and a priority may change,
depending on the connected equipment or video signals.)
FAN SPEED
Sets the rotation speed of the fan.
FAN SPEED
Sets the rotation speed of the fan.
As this number increases, the rotation speed becomes
faster. When set to AUTO, the rotation speed of the fan will
change depending on the internal temperature.
SIZE
Selects screen size. (See page 6.)
MUTE AUDIO
Can temporarily turn off the volume.
INFORMATION
If you press
SIZE
Selects screen size. (See page 6.)
MUTE AUDIO
Can temporarily turn off the volume.
INFORMATION
If you press
, monitor information can be checked.
COPY SETTING VALUE
When the monitor has been connected to multiple monitors
When the monitor has been connected to multiple monitors
with RS-232C, you can copy the primary setting details to
the secondary. Perform operations with the primary monitor.
Select the ID No. of the monitor that you would like copy to
with COPY TO ID No., then select COPY and press
MENU
.
If you select ALL, settings will be copied to all monitors.
When you would like to confirm the ID No. that is set to the
monitor, select ID No. and press
. The ID No. will be
displayed on the screen.
n
OPTION
DATE/TIME SETTING
Set the date and time. Press
Set the date and time. Press
or
to select the date
and time, and press
or
to change the numerical
values.
Set the date in “Year/Month/Day” order.
Set the time on a 24-hour basis.
SCHEDULE (See page 14.)
You can set the time to switch the monitor on and off.
INPUT SELECT
Select the input mode to be used in PC/AV DVI-D input
SCHEDULE (See page 14.)
You can set the time to switch the monitor on and off.
INPUT SELECT
Select the input mode to be used in PC/AV DVI-D input
terminal, PC/AV HDMI input terminal and PC RGB/AV
component input terminals.
AUDIO SELECT
Selects the terminal used to input audio signals in each input mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input
AUDIO SELECT
Selects the terminal used to input audio signals in each input mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input
terminal outputs any of the following resolutions, make a
selection from the following options.
480 LINES .......... AUTO, 640x480 or 848x480
768 LINES .......... AUTO, 1024x768, 1280x768, 1360x768 or
1366x768
1050 LINES ........1400x1050 or 1680x1050
ZOOM2 SPECIAL SETTING (See page 13.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.
MODE1 ............... Over-scan display
MODE2 ...............Under-scan display
MODE3 ............... Under-scan display when the input signal
is 1080i/p. Otherwise, over-scan display
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to
POWER MANAGEMENT determines whether or not to
switch modes from no signal to the input signal standby
mode.
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is
connected to AV S-video and AV video input terminal. (AUTO
/ PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)
When AUTO is selected, the color system is automatically
set according to the input signal.
AUDIO OUTPUT(RCA)
Sets the volume of sound output from the audio output
AUDIO OUTPUT(RCA)
Sets the volume of sound output from the audio output
terminals. When set to VARIABLE2, audio is not output from
the external speaker terminals.
VARIABLE .......... You can adjust the volume using VOLUME.
FIXED ................. Disables volume adjustment and fixes the
sounds.
When the PN-ZB02 (optional) is attached:
VARIABLE1 ........ You can adjust the volume using VOLUME.
VARIABLE2 ........ You can adjust the volume using VOLUME,
but audio is not output from the external
speaker terminals.
FIXED ................. Disables volume adjustment and fixes the
sounds.
E
12
Menu Items
n
MULTI
ENLARGE (See page 13.)
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
Sets whether or not to use the enlarge function.
ADVANCED (ENLARGE)
ENLARGE H / ENLARGE V
......... Sets the number of screen splits (number of
monitors) in the horizontal/vertical direction used for
the enlargement.
ENLARGE-POS
......... Specify the split screen to be displayed when the
enlargement function is used.
H-POS / V-POS
......... Adjust the horizontal/vertical position of the enlarged
screen.
BEZEL ADJUST
Sets whether or not to use the frame correction function.
ADVANCED (BEZEL ADJUST)
BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /
Sets whether or not to use the frame correction function.
ADVANCED (BEZEL ADJUST)
BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /
BEZEL ADJUST (RIGHT) / BEZEL ADJUST (LEFT)
......... Adjusts so that the top/bottom/left/right connecting
joints of grouped units will be displayed smoothly
when a group of monitors are aligned in multiples to
display a single image.
BEZEL H / BEZEL V
......... Sets the frame width of the display.
n
PIP/PbyP
PIP MODES
Sets the display method.
Sets the display method.
OFF .........Displays one screen.
PIP ...........Displays a sub screen inside a main screen.
PbyP ........Displays a main screen and a sub screen in a line.
PbyP2 ......Displays a main screen which measures 1024 pixels
in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen
transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or
PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode.
If the main screen is displayed as a full screen by the AUTO
OFF function, the sound for the main screen is output even
when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen
are input in PIP, PbyP, or PbyP2 mode.
MANUAL ....... Displays a main screen and a black sub screen.
AUTO ............ Displays the main screen as a full screen.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL,
CONTRAST, TINT, COLORS and GAMMA cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot
be set.
WHITE BALANCE, PRESET, USER, COPY TO USER, and
GAMMA
• When the COLOR MODE is set to VIVID, GAMMA can not
be adjusted.
• If GAMMA is set to USER, the following items cannot be
set.
WHITE BALANCE, PRESET, USER, and COPY TO USER
• STANDBY MODE cannot be set to LOW POWER when
SCHEDULE is effective or when OFF is selected for LED in
FUNCTION.
n
Dual screen display
You can display the screens of the PC input signal and AV
input signal simultaneously.
Set this function with “PIP MODES” in the PIP/PbyP menu.
PIP
Main screen
Sub
screen
A sub screen is displayed
inside a main screen.
PbyP
Main
screen
Sub
screen
A main screen and a sub
screen are displayed in a
line.
PbyP2
Main screen
Sub
screen
Displays a main screen
which measures 1024
pixels in the longest
direction and a sub
screen in a line.
* The currently selected input signal is displayed on the main
screen.
* You cannot simultaneously display the screens of signals
of the same type, such as two types of PC input signals or
two types of AV input signals.
* The dual screen display cannot be used with the
combination of PC DVI-D and AV HDMI or of AV DVI-D and
PC HDMI.
TIPS
• You might infringe on a copyright of the author which is
protected by copyright law when you display the images of
the computer screen and television/VCR simultaneously for
profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as
the screen size for single-screen display. The Dot by Dot
screen is displayed in NORMAL size except when it is set
as the PIP main screen.
• When dual-screen display is selected, the AUTO INPUT
CHANGE function is disabled.
• When dual-screen display is selected, the screen cannot
be enlarged.
• When dual-screen display is selected, the INPUT SELECT
options cannot be set.
Click on the first or last page to see other PN-V601 (serv.man8) service manuals if exist.