DOWNLOAD Sharp PN-L602B (serv.man6) Service Manual ↓ Size: 11.82 MB | Pages: 127 in PDF or view online for FREE

PN-L702B/L602B　INSTALLATION, ADJUSTMENT, SETTING

 2 – 2

n

Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/disconnecting cables. Also, read the

manual of the equipment to be connected.

n

Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the input and output terminals may cause
malfunctions and the other problems.

n

Images may not be displayed properly depending on the computer (video card) to be connected.

n

A screen with 1920 x 1080 resolution may not be displayed correctly on “PC RGB”. In this case, check the settings of your computer (video

card) to verify that input signals conform to specifications of this monitor.

n

If there is a check box to disable EDID in display control panel, check it when using “PC RGB”.

n

Use the automatic screen adjustment when a PC screen is displayed for the first time using “PC D-SUB” or “PC RGB”, or when the setting of

the PC is changed. The screen is adjusted automatically when “SELF ADJUST” in the OPTION menu is set to “ON”.

n

If the audio output from the playback device is connected directly to speakers or other devices, the video on the monitor may appear delayed
from the audio portion.

Audio should be played through this monitor by connecting the playback device to the monitor’s audio input, and connecting the monitor’s

audio output to the speakers or other devices.

n

The audio input terminals used in each input mode are factory-set as follows.

n

Attach a speaker cable core (included with the PN-ZB01) to the end of the speaker cable connected to the monitor. (When you attach the exter-

nal speaker to the monitor)

n

To use the touch panel, the touch panel driver and pen soft must be installed from the supplied CD-ROM and the touch panel must be connected to your PC.

n

Connected to the touch panel.

Installing the touch panel driver.
3Refer to page 2 - 26  "3. SETTING UP THE PC (TOUCH PANEL DRIVER)".
To instal the pen soft, refer to the manual for the pen soft. 

PC D-SUB

PC DVI-D

PC RGB

Audio input terminal

AV DVI-D

Audio1 input terminal

AV COMPONENT(BNC)
AV S-VIDEO

AV VIDEO (BNC)

Audio2 input terminal

AV COMPONENT (D-SUB)

AV VIDEO (D-SUB)

Audio input terminal

PC HDMI
AV HDMI

PC/AV HDMI input terminal

ŘũŦůġŵũŦġőŏĮśŃıIJ
ĩŰűŵŪŰůŢŭĪġŪŴġŢŵŵŢŤũŦť

For power
outlet

Power cord
(Supplied)

USB port

PC D-SUB
input terminal

Audio input
terminal

Audio output
Vterminals

RS-232C
input terminal

RS-232C
output terminal

PC/AV HDMI
input terminal

PC/AV DVI-D input terminal

PC/AV DVI-D output terminal

LAN terminal

External speaker terminals

Audio 1 input terminals
Audio 2 input terminals

PC RGB
input terminals

AV component input terminals

AV video
Ainput terminal

AV S-video input terminal

AC input
terminal

PN-L702B/L602B　INSTALLATION, ADJUSTMENT, SETTING

 2 – 3

■ CONNECTION WITH A PC OR AV EQUIPMENT

■ CONNECTION WHEN THE PN-ZB01 (OPTIONAL) IS ATTACHED

The PN-ZB01 expansion board (optional) allows the use of additional connection terminals.

You can control the monitor from a PC on a network by connecting a commercially available LAN cable between this terminal and a network.

PC/AV HDMI input terminal

n

Use a commercially available HDMI cable (conforming to the HDMI standard).

n

Set HDMI of INPUT SELECT on the OPTION menu according to the device to be connected.

n

Select the audio input terminal to be used in PC HDMI or AV HDMI of AUDIO SELECT on the

OPTION menu. 

When HDMI is selected, connection to the audio input terminal is unnecessary.

PC D-SUB input terminal

n

Set D-SUB of INPUT SELECT on the OPTION menu according to the device to be connected.

n

Common terminal for AV COMPONENT and AV VIDEO.

n

When the PN-ZB01 (optional) is attached, select the audio input terminal to be used in PC D-SUB of

AUDIO SELECT on the OPTION menu.

n

To use with AV VIDEO (D-SUB), connect the green terminal to the device’s video output.

Audio input terminal

n

Use an audio cable without resistance.

n

When the PN-ZB01 (optional) is attached, set the audio input terminal used for each input mode in

AUDIO SELECT on the OPTION menu.

Audio output terminals

n

The output sound varies depending on the input mode.

n

The volume of the output sound can be fixed by setting AUDIO OUTPUT(RCA) on the OPTION
menu.

n

It is not possible to control the sound output from the audio output terminals with the AUDIO menu.

RS-232C input terminal

RS-232C output terminal

n

You can control the monitor from a PC by connecting a commercially available RS-232 straight cable
between these terminals and the PC.

USB port

n

To use the touch panel, connect the touch panel to your computer with the provided USB cable. 
3Refer to "Touch Panel Driver Operation Manual".

PC/AV DVI-D input terminal

n

Set DVI of INPUT SELECT on the OPTION menu according to the device to be connected.

n

Select the audio input terminal to be used in PC DVI-D or AV DVI-D of AUDIO SELECT on the
OPTION menu.

PC RGB input terminals

n

Set BNC of INPUT SELECT on the OPTION menu to PC RGB when using the PC RGB input terminals.

n

Select the audio input terminal to be used in PC RGB of AUDIO SELECT on the OPTION menu.

AV component input 

terminals

n

Set BNC of INPUT SELECT on the OPTION menu to AV COMPONENT when using the AV compo-
nent input terminals.

n

Select the audio input terminal to be used in AV COMPONENT of AUDIO SELECT on the OPTION menu.

n

Cannot be used when D-SUB in INPUT SELECT on the OPTION menu is set to AV COMPONENT.

AV S-video input terminal

n

Select the audio input terminal to be used in AV S-VIDEO of AUDIO SELECT on the OPTION menu.

AV video input terminal

n

Select the audio input terminal to be used in AV VIDEO of AUDIO SELECT on the OPTION menu.

n

Cannot be used when D-SUB in INPUT SELECT on the OPTION menu is set to AV VIDEO.

Audio1 input terminals/

 Audio2 input terminals

n

Set the audio input terminal to be used in each input mode in AUDIO SELECT on the OPTION menu.

H

V

R

G

B

Cr/Pr

Y

Cb/Pb

PN-L702B/L602B　INSTALLATION, ADJUSTMENT, SETTING

 2 – 4

n

The video of the PC/AV DVI-D input can be output to an external

device.

n

Outputting HDCP-encrypted video requires an external device which

supports HDCP.

n

This terminal allows the daisy chain connection of up to 5 monitors.

n

The length of the signal cables or surrounding environment may

affect the image quality.

n

The screen may not display properly when using terminals other
than “PC DVI-D”/“AV DVI-D” for the input mode. In this case, turn

off the power to all the monitors connected in a daisy chain and

then turn the power on again.

n

When connecting monitors in a daisy chain set “AUTO INPUT
CHANGE” to “OFF”.

n

Video output is disabled in the following cases.

---When the power is turned “off”.

---When the monitor is in input signal waiting mode.

n

To use an external speaker, set “SPEAKER SELECT” on the SETUP
menu to “EXTERNAL”.

n

Be sure to use external speakers with an impedance of 6 

Ω and a

rated input of at least 10 W.

1 ) Attach a speaker cable core (included with the PN-ZB01) to the

end of the speaker cable connected to the monitor.

2 ) While pushing the tab, insert the tip of the cable.

3 ) Release the tab.

n

Be sure to connect the + and - terminals and the left and right
speakers properly.

n

Avoid short circuiting the + and - terminals.

n

When “SPEAKER SELECT” is set to “EXTERNAL”, the internal

speaker is disabled.

First monitor

Second monitor

Digital signal (DVI) cables
(commercially available)

To PC digital RGB output terminal

shows the signal flow

PC/AV DVI-D 
output terminal

PC/AV DVI-D 
input terminals

PC/AV DVI-D 
output terminals

Approx.
3-15/16 inch
(10 cm)

PN-L702B/L602B　INSTALLATION, ADJUSTMENT, SETTING

 2 – 5

■ CONTROLLING THE MONITER WITH A PC 

You can control this monitor from a PC via RS-232C (COM port) on the

PC.

You can also connect multiple monitors via a daisy chain by using a PC.
By assigning ID numbers to each monitor (see page 19), you can make

input mode selection/adjustment or can check the status of a specific

monitor.

You can also connect multiple monitors via a daisy chain by using a PC.
By assigning ID numbers to each monitor, you can make input mode

selection/adjustment or can check the status of a specific monitor.

n

To control the monitor via RS-232C, set RS-232C/LAN SELECT

to RS-232C.

n

You cannot use RS-232C and LAN control simultaneously.

Connect with RS-232 straight cable between the PC's COM port (RS-
232C connector) and the RS-232C input terminal on the monitor.

Connect with RS-232 straight cable between the PC's COM port (RS-
232C connector) and the RS-232C input terminal on the first monitor.

Next, connect RS-232 straight cable to the first monitor's RS-232C out-

put terminal and to the second monitor's RS-232C input terminal. Con-

nect in the same way to the third and subsequent monitors.

Up to 25 monitors can be connected. (Depending on the length of the
cable used and the surrounding environment.)

Set the RS-232C communication settings on the PC to match the moni-

tor's communication settings as follows.

*

1

Set to the same baud rate as the “BAUD RATE” setting of 
SETUP menu.

When connecting multiple monitors in a daisy chain, set all mon-

itors to the same “BAUD RATE”.

RS-232C input 
terminal

RS-232 straight cable
(commercially available)

To COM port

PC

38400 bps (Initial setting) 

*1

8 bits

None

1 bit

None 

First monitor

Second monitor

RS-232C
output terminal

RS-232C
input terminal

RS-232 straight cables
(commercially 
available)

To COM port

PC