DOWNLOAD Sharp LL-T2010W (serv.man23) Service Manual ↓ Size: 738.05 KB | Pages: 30 in PDF or view online for FREE

About the ColorSync profile
ColorSync is the Apple Corporation's color
management system and is a function that
enables color resolution to be realized when
used with a compatible application. A ColorSync
profile describes the color characteristics of the
LCD monitor.
Notes:
- This monitor's ColorSync profile works with

MacOS8.5 or above.

- When using the ColorSync profile, set  [COLOR

CONTROL] to [STD].

Notes:
- A floppy disk drive is necessary. In addition, it is

necessary to have PC Exchange or File
Exchange installed in your system.

- Depending on the type of computer or OS,

command names and methods may differ. Please
follow the computer’s own operation manual
while reading this.

1. Place the Utility Disk (provided) into the

computer’s floppy disk drive.

2. Copy the profile to be used from the Mac folder

on the Utility Disk to the ColorSync profile folder
located within the system folder.

3. Using the ColorSync on the control panel,

choose the profile to be used.

An arm or stand based on the VESA standard
(commercially available) can be attached to the
monitor.
Procurement of the arm or stand is at the custom-
er's discretion.

Attachments must satisfy the following.
- Compatible with the VESA standard.
- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

Note:
- Do not overly bend the cable or add extension

cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

1. Spread out a soft cloth on a suitable horizontal

surface.

2. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

3. Remove the stand cover.

CAUTION!
Be careful not to cut or jam your fingers.

(Rear View)

Stand cover

Lift one side

4. Remove the two screws, and remove the cover.

5. Remove the four screws and then remove the

stand from the monitor.

6. Attach the arm to the monitor with the four

screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 8 mm ~ 10 mm protruding
from the surface to be attached. Using different
screws could lead to malfunction or may lead to
the monitor falling off,internal damaged,personal
injury.

8

10mm

Cover

Two screws

Four screws

Stand

Four screws

Screw used to attach arm

Arm

Part of monitor to which arm is
attached

An arm or stand based on the VESA standard
(commercially available) can be attached to the
monitor.
Procurement of the arm or stand is at the custom-
er's discretion.

Attachments must satisfy the following.
- Compatible with the VESA standard.
- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

Note:
- Do not overly bend the cable or add extension

cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

1. Spread out a soft cloth on a suitable horizontal

surface.

2. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

3. Remove the stand cover.

CAUTION!
Be careful not to cut or jam your fingers.

(Rear View)

Stand cover

Lift one side

4. Remove the two screws, and remove the cover.

5. Remove the four screws and then remove the

stand from the monitor.

6. Attach the arm to the monitor with the four

screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 8 mm ~ 10 mm protruding
from the surface to be attached. Using different
screws could lead to malfunction or may lead to
the monitor falling off,internal damaged,personal
injury.

8

10mm

Cover

Two screws

Four screws

Stand

Four screws

Screw used to attach arm

Arm

Part of monitor to which arm is
attached

An arm or stand based on the VESA standard
(commercially available) can be attached to the
monitor.
Procurement of the arm or stand is at the custom-
er's discretion.

Attachments must satisfy the following.
- Compatible with the VESA standard.
- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

Note:
- Do not overly bend the cable or add extension

cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

1. Spread out a soft cloth on a suitable horizontal

surface.

2. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

3. Remove the stand cover.

CAUTION!
Be careful not to cut or jam your fingers.

(Rear View)

Stand cover

Lift one side

4. Remove the two screws, and remove the cover.

5. Remove the four screws and then remove the

stand from the monitor.

6. Attach the arm to the monitor with the four

screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 8 mm ~ 10 mm protruding
from the surface to be attached. Using different
screws could lead to malfunction or may lead to
the monitor falling off,internal damaged,personal
injury.

8

10mm

Cover

Two screws

Four screws

Stand

Four screws

Screw used to attach arm

Arm

Part of monitor to which arm is
attached