DOWNLOAD Sharp LL-T2010W (serv.man2) Service Manual ↓ Size: 92.72 KB | Pages: 4 in PDF or view online for FREE

Model
LL-T2010W (serv.man2)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
92.72 KB
Type
PDF
Document
Service Manual
Brand
Device
Monitor / (1) Outline of product, nomenclature and function.
File
ll-t2010w-sm2.pdf
Date

Sharp LL-T2010W (serv.man2) Service Manual ▷ View online

LL-T2010W
OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1 – 1
CHAPTER 1. OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1. SPECIFICATIONS
■ 
■ 
■ 
■ 
PRODUCT SPECIFICATIONS
• LCD display
Diagonal 51cm
Advanced-Super-V and Anti Glare Low Reflection TFT LCD module
• Resolution (max.)
UXGA 1600 
u
 1200 pixels
• Displayable colors (max.)
16.77 million colors (8 bit)
• Brightness (max.)
220cd/m
2
•  Dot pitch
0.255 (H) 
u
 0.255 (V) mm
•  Contrast ratio
350 : 1
•  Angle of visibility
Left-right 170°
 
; Up-down 170°
•  Screen display size
Horizontal 408 mm 
u
 Vertical 306 mm
• Video signal
Analog: Analog RGB (0.7Vp-p) [75
]
Digital: DVI standard based on 1.0
• Sync signal
Separate Sync (TTL level: +/-), Sync on Green,
Composite Sync (TTL level: +/-)
• Expansion compensation
Digital screening 
Enlarging VGA/SVGA/XGA/SXGA etc. with a compensation process.
(no enlarging, based on a fixed aspect ratio, and enlarging to full
screen size.)
•  Plug & Play
VESA: DDC2B compatible
• Power management
VESA: based on DPMS
DVI: based on DMPM
• Input signal terminal
Analog: 15 pin mini D-sub (3 rows)
Digital/Analog: 29 pin DVI-I
•  USB hub function
1 upstream port, 2 downstream ports
(bus-powered hub based on USB standard Rev 1.1)
• Screen tilt
Upward 0° - 30°
 
; downward 0° - 5°
• Screen swivel
90° from left through right
• Power supply
AC100-240V, 50/60Hz (Use special AC adapter, type NL-A51J of
Sharp Corporation.)
•  Temperature of operating environment
5 - 35°C
• Power consumption
Maximum 52W (5.5W when in power-saving mode)
(Use special AC adapter.)
• Dimensions (W 
u
 D 
u
 H)
483 mm 
u
 218 mm 
u
 479 mm
•  Weight (excluding AC adapter)
Approx. 10.5 kg, Display area only, approx. 7.9kg
■ 
■ 
■ 
■ 
DIMENSIONS (Units: mm)
Length of analog signal cable: approx. 1.8m
*
Length of USB cable inclued: approx. 2.0m
*
Length from analog signal input terminal
Special AC adapter
Option
Digital signal cable (NL-C01E): Approx. 2.0 m
Analog signal cable (NL-C02E): Approx. 2.0 m
483
227
78
4
7
9
3
9
7
2
1
8
Approx. H 140 mm x D 70 mm x H 41 mm
Approx. 1.8 m
LL-T2010W
OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1 – 2
Relevant signal timings (analog)
•  All are compliant only with non-interlaced.
•  Frequencies for Power Macintosh and the Sun Ultra series are refer-
ence values. To connect, another adapter (purchased separately)
may be required.
•  If the monitor is receiving timing signals that are not compatible, [OUT
OF TIMING] will appear. Follow your computer's instruction manual
to set the timing so that it is compatible with the monitor.
•  If the monitor is not receiving any signal (synch signal), [NO SIGNAL]
will appear.
Relevant signal timings (digital)
•  All are compliant only with non-interlaced.
• A computer with an output terminal conforming to DVI (DVI-D24 pin
or DVI-I29 pin) and with UXGA output capability can be connected
here. 
Depending on the type of computer to be connected, the display may
not work correctly. In order to connect, it is necessary to purchase a
digital signal cable (model name: NL-C01E) separately.
•  If the monitor is receiving timing signals that are not compatible, [OUT
OF TIMING] will appear. Follow your computer's instruction manual
to set the timing so that it is compatible with the monitor.
•  If the monitor is not receiving any signal (synch signal), [NO SIGNAL]
will appear.
The analog signal input connector pin
Display mode
Hsync 
(kHz)
Vsync 
(Hz)
Dot frequency
 (MHz)
VESA
640 
u
 480
31.5kHz
60Hz
25.175MHz
37.9kHz
72Hz
31.5MHz
37.5kHz
75Hz
31.5MHz
43.4kHz
85Hz
36.0MHz
640 
u
 400
37.9kHz
85Hz
31.5MHz
720 
u
 400
37.9kHz
85Hz
35.5MHz
800 
u
 600
35.1kHz
56Hz
36.0MHz
37.9kHz
60Hz
40.0MHz
48.1kHz
72Hz
50.0MHz
46.9kHz
75Hz
49.5MHz
53.7kHz
85Hz
56.25MHz
1024 
u
 768
48.4kHz
60Hz
65.0MHz
56.5kHz
70Hz
75.0MHz
60.0kHz
75Hz
78.75MHz
68.7kHz
85Hz
94.5MHz
1152 
u
 864
67.5kHz
75Hz
108.0MHz
1280 
u
 960
60.0kHz
60Hz
108.0MHz
1280 
u
 1024
64.0kHz
60Hz
108.0MHz
80.0kHz
75Hz
135.0MHz
1600 
u
 1200
75.0kHz
60Hz
162.0MHz
US text
720 
u
 400
31.5kHz
70Hz
28.3MHz
Power
Macintosh 
series
640 
480
35.0kHz
66.7Hz
30.2MHz
832 
u
 624
49.7kHz
74.6Hz
57.3MHz
1024 
u
 768
60.2kHz
75Hz
80.0MHz
1152 
u
 870
68.7kHz
75Hz
100.0MHz
1280 
u
 1024
64.0kHz
60Hz
108.0MHz
80.0kHz
75Hz
135.0MHz
1600 
u
 1200
75.0kHz
60Hz
162.0MHz
Sun Ultra 
series
1024 
u
 768
48.3kHz
60Hz
64.13MHz
53.6kHz
66Hz
70.4MHz
56.6kHz
70Hz
74.25MHz
1152 
u
 900
61.8kHz
66Hz
94.88MHz
71.8kHz
76.2Hz
108.23MHz
1280 
u
 1024
71.7kHz
67.2Hz
117.01MHz
81.1kHz
76Hz
134.99MHz
1600 
u
 1000
68.6kHz
66Hz
135.76MHz
Display mode
Hsync 
(kHz)
Vsync 
(Hz)
Dot frequency
 (MHz)
VESA
640 
u
 480
31.5kHz
60Hz
25.175MH
37.9kHz
72Hz
31.5MHz
37.5kHz
75Hz
31.5MHz
800 
u
 600
37.9kHz
60Hz
40.0MHz
48.1kHz
72Hz
50.0MHz
46.9kHz
75Hz
49.5MHz
1024 
u
 768
48.4kHz
60Hz
65.0MHz
56.5kHz
70Hz
75.0MHz
60.0kHz
75Hz
78.75MHz
1152 
u
 864
67.5kHz
75Hz
108.0MHz
1280 
u
 960
60.0kHz
60Hz
108.0MHz
1280 
u
 1024
64.0kHz
60Hz
108.0MHz
1600 
u
 1200
75.0kHz
60Hz
162.0MHz
US text
720 
u
 400
31.5kHz
70Hz
28.3MHz
Number
Function
1
Red video signal input
2
Green video signal input
3
Blue video signal input
4
GND
5
GND
6
For red video signal GND
7
For green video signal GND
8
For blue video signal GND
9
N.C.
10
GND
11
GND
12
DDC data
13
For Hsync signal input
14
For Vsync signal input
15
DDC clock
5
1
2
3
4
10
6
7
8
9
15
11
12
13
14
LL-T2010W
OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1 – 3
The DVI-I input connector pin
Power management
The monitor is based on the VESA DPMS*
1
 and the DVI DMPM*
2
 stan-
dards.
To activate the monitor's Power Management function, both the video
card and the computer must conform to the VESA DPMS standard and
the DVI DMPM standard.
*1  DPMS: Display Power Management Signalling
*2  DMPM: Digital Monitor Power Management
DDC (Plug & Play)
This monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for carrying out Plug & Play functions on the
monitor or PC. It transfers information such as degree of resolution
between the monitor and PC. You can use this function if your PC is
DDC compliant and if it is set so that it can detect the Plug & Play mon-
itor.
There are many varieties of DDC due to the differences between sys-
tems. This monitor works with DDC2B.
2. TECHNICAL SPECIFICATIONS
*
 Specifications and a part of the appearance are subject to change without notice.
No.
Function
No.
Function
1
TMDS data 2-
16
Hot plug detection
2
TMDS data 2+
17
TMDS data 0-
3
TMDS data 2/4 shield
18
TMDS data 0+
4
N.C.
19
TMDS data 0/5 shield
5
N.C.
20
N.C.
6
DDC clock
21
N.C.
7
DDC data
22
TMDS clock shield
8
Analogue vertically 
synchronised signal
23
TMDS clock +
9
TMDS data 1-
24
TMDS clock -
10
TMDS data 1+
C1
Analogue red image signal
11
TMDS data 1/3 shield
C2
Analogue green image signal
12
N.C.
C3
Analogue blue image signal
13
N.C.
C4
Analogue horizontally 
synchronised signal
14
+5V
C5
Analogue GND
15
GND
1
9 10
17 18 19 20 21 22 23 24
11 12 13 14 15 16
2 3 4 5 6 7 8
C1 C2
C3 C4
C5
DPMS mode
Screen
Power
consumption
H-sync
V-sync
ON
Display on
52W
Yes
Yes
STANDBY
Display off
5.5W
No
Yes
SUSPEND
Yes
No
OFF
No
No
DPMS mode
Screen
Power consumption
ON
Display on
52W
OFF
Display off
5.5W
Item
MIN
TYP
MAX
Unit
Power supply voltage
AC
90
100
110
V
Working temperature range
+5
.
+35
°C
Storing temperature range
-20
.
+60
°C
Humidity range
20
.
85
%RH
Visual angle range
Vertical (CR 
u
 10)
m
70
m
85
.
Temperature
Horizontal (CR 
u
 10)
m
70
m
85
.
Temperature
Contrast ratio(CR)
(
θ
 = 0°)
.
350
.
.
Response speed
Leading (
τ
r)
.
20
.
ms
Trailing (
τ
d)
.
5
.
ms
Screen white chromaticity
(X)
0.283
0.313
0.343
.
(Y)
0.299
0.329
0.359
.
White surface luminance
(Y
L
)
170
220
.
cd/m
2
Module model number
LQ201U1LZ01
LL-T2010W
OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION
1 – 4
■ 
■ 
■ 
■ 
PRODUCT DESCRIPTION
1. INPUT button
To switch between the signal's input terminals. (Analog RGB input ter-
minal 
13
 DVI-I input terminal)
2. MENU button
This button is used to pop-up, select and close the OSD Menu.
3. SELECT button
This button is used to select menu options when the OSD Menu is dis-
played.
4.
e d
 buttons
When the On Screen Display (OSD) Menu is displayed:
These buttons are used to increase or decrease the value of a selected
option.
When the OSD Menu is not displayed:
These buttons are used to adjust backlight brightness.
5. Power LED
This LED is lit green when in use and orange when in power-saving
mode.
6. Power button
Pressing this button turns the power on. (After turning the power on, it
may take a little time before the screen displays.)
Press the button again to turn the power off.
7. Analog RGB input terminal
Remove the cover to see the analog RGB input terminal. At the time of
leaving the factory the analog signal cable is connected.
8. Power terminal
Remove the cover to see the power terminal. The AC adapter is con-
nected here.
9. Security lock anchor
By connecting a security lock (commercially available) to the security
lock anchor, the monitor is fixed so that it cannot be transported.
The security slot works in conjunction with Kensington Micro Saver
Security Systems.
10. Analog signal cable
Connects to the computer's analog RGB output terminal.
11. USB port
Remove the cover to see the USB port (upstream: 1 port, downstream:
2 ports).
12. DVI-I input terminal
Remove the cover to locate the DVI-I input terminal (DVI-I29 pin).
The computer's digital RGB output terminal or analog RGB output ter-
minal can be connected here.
For a digital signal input: It can be connected to a computer with a DVI-
compatible output terminal (DVI-D24 pin or DVI-I29 pin) and which has
UXGA output ability. Depending on the computer to be connected, cor-
rect display may or may not be possible.
To be able to connect, a cable that is to be purchased separately is
required.
To connect to a digital RGB output terminal: Digital signal cable (model
name: NL-C01E)
To connect to an analog RGB output terminal: Analog signal cable
(model name: NL-C02E)
13. Ventilation openings
Note: Never block the ventilation openings as this may lead to over-
heating inside the monitor and result in malfunction.
Adjusting the angle of the monitor
Lightly holding both sides of the monitor, adjust it to a suitable viewing
angle.
Caution: Pressure from hands on the LCD panel could cause damage.
1
Front view
Rear view
2 3
4
5 6
9
7
8
13
13
13
10
12
11
approx.30
approx.45
approx.45
approx.5
Display

Sharp LL-T2010W (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sharp LL-T2010W (serv.man2) Service Manual ↓ Size: 92.72 KB | Pages: 4 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp LL-T2010W (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp LL-T2010W (serv.man2) Monitor. Information contained in Sharp LL-T2010W (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.