DOWNLOAD Sharp LL-T1520 (serv.man18) Service Manual ↓ Size: 3.06 MB | Pages: 127 in PDF or view online for FREE

Installing monitor set-up information into Win-
dows2000, and setting the monitor's ICC profile as
a predetermined value.
This explanation assumes that the floppy disk drive
is "A drive".
1. Place the Utility Disk (provided) into the

computer's A drive.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. Click on [Properties], [Driver] and [Update

Driver].

6. When [Upgrade Device Driver Wizard] appears,

click [Next].

7. Check [Display a list of the known drivers for

this device so that I can choose a specific
driver] and click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [A:], and click [OK].

9. Select the monitor from the list displayed and

click [Next].

10. Click [Next], confirm that the monitor's name

appears on the screen, and click [Finish]. If
[The Digital Signature Not Found] appears, click
[Yes].

11. Click on [Close].
12. Click [OK], and close the window.
13. Remove the Utility Disk from the A drive.

Installing monitor set-up information into
WindowsMe, and setting the monitor's ICC profile
as a predetermined value.
This explanation assumes that the floppy disk drive
is "A drive".

If the "Add new Hardware Wizard" has appeared:
1. Place the Utility Disk (provided) into the

computer's A drive.

2. Check [Specify the location of the driver

[Advanced]] and click [Next].

3. Check [Display a list of all the drivers in a

specific location, so you can select the driver
you want.], then click [Next].

4. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [A:], and click [OK].

5. Select the monitor details from the list, then

click [Next], [Next], and [Finish]. If the "Add new
Hardware Wizard" appears, repeat the
installation commands beginning from 2 above.

6. Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not ap-
peared:
1. Place the Utility Disk in the computer's A drive.
2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Check [Specify the location of the driver

[Advanced]] and click [Next].

7. Check [Display a list of all the drivers in a

specific location, so you can select the driver
you want.] and click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [A:], and click [OK].

9. Select the monitor details, then click [Next],

[Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.
12. Remove the Utility Disk from the A drive.

Installing monitor set-up information into
WindowsXP, and setting the monitor's ICC profile
as a predetermined value.
This explanation assumes that the floppy disk drive
is "A drive".
1. Place the Utility Disk in the computer's A drive.
2. Click on the [Start] button. Choose [Control

Panel].

3. Switch to "Classic View".
4. Double click on [Display].
5. Click on [Settings], [Advanced] and [Monitor].
6. Click on [Properties], [Driver] and [Update

Driver].

7. When [Hardware Update Wizard] appears,

check [Install from a list or specific location
[Advanced]] and click [Next].

8. Check [Don't search. I will choose the driver to

install.] and click [Next].

9. Click on [Have Disk], confirm that [Copy

manufacturer's  files from:]  is [A:], and click
[OK].

10. Select the monitor from the list displayed and

click [Next].
If [has not passed Windows Logo testing...]
appears, click [Continue Anyway].

11. Confirm that the monitor's name appears on the

screen.

12. Click on [Finish].
13. Click on [Close].
14. Click [OK], and close the window.
15. Remove the Utility Disk from the A drive.

Installing the monitor’s ICC profile. (If the set-up
information has already been installed, so too has
the profile, and there is no need to install it.)
This explanation assumes that the floppy disk drive
is "A drive".
1. Place the Utility Disk in the computer’s A drive.
2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings] and [Advanced].
5. Click on [General] and from [Compatibility]

select [Apply the new display setting without
restarting], then click on [Color Management].

6. Click [Add], and select [3 ½ Floppy [A:]] as the

file location.

7. Choose the color profile that you would like to

install, and click on [Add].

8. Choose the profile and click on [Set As Default].
9. Click [OK], and close the window.
10. Remove the Utility Disk from the A drive.

When using an ICC profile, set  [COLOR
MODE] and [WHITE BALANCE] to [STD], and
set [HUE] and [SATURATION] to [0].

About the ColorSync profile
ColorSync is the Apple Corporation's color
management system and is a function that
enables color resolution to be realized when
used with a compatible application. A ColorSync
profile describes the color characteristics of the
LCD monitor.
Notes:
- This monitor's ColorSync profile works with

MacOS8.5 or above.

- When using the ColorSync profile, set  [COLOR

MODE] and [WHITE BALANCE] to [STD], and
set [HUE] and [SATURATION] to [0].

Notes:
- A floppy disk drive is necessary. In addition, it is

necessary to have PC Exchange or File
Exchange installed in your system.

- Depending on the type of computer or OS,

command names and methods may differ. Please
follow the computer’s own operation manual
while reading this.

1. Place the Utility Disk (provided) into the

computer’s floppy disk drive.

2. Copy the profile to be used from the Mac folder

on the Utility Disk to the ColorSync profile folder
located within the system folder.

3. Using the ColorSync on the control panel,

choose the profile to be used.

An arm or stand based on the VESA standard
(commercially available) can be attached to the
monitor.
Procurement of the arm or stand is at the custom-
er's discretion.

Attachments must satisfy the following.
- Compatible with the VESA standard
- Have a gap of 75 mm x 75 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

- Be careful not to overly bend the cable or add

extension cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the
operation manual included with the arm or stand.

1. Turn off the monitor’s power and unplug AC plug

from AC outlet.

2. Remove the cable.
3. Spread out a soft cloth on a suitable horizontal

surface.

4. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

5. Remove the four screws and then remove the

stand from the monitor.

Notes:
- The stand is specially made for use with this

monitor. Once having removed the stand, never
attempt to attach it to another device.

- Once having removed the screws, store them

together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to a
malfunction.

6. Attach the arm to the monitor with the four

screws.

Notes:
- The screws used to attach the arm should be M4

screws with a length of 6 mm ~ 8 mm protruding
from the surface to be attached. Using different
screws could lead to malfunction or may lead to
the monitor falling off,internal damaged,personal
injury.

6 - 8 mm

Screw used to attach arm

Arm

Part of monitor to which
arm is attached