DOWNLOAD Sharp LL-T1520 (serv.man18) Service Manual ↓ Size: 3.06 MB | Pages: 127 in PDF or view online for FREE

When connecting to an analog RGB output terminal:
- Use an analog signal cable (model name: NL-

C02E).

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then
tighten the screws at both sides.

Set the monitor as follows when establishing a
digital connection with a Power Mac using an ADC-
DVI adapter made by Belkin. (Operation has been
checked with the Power Mac G4 M7627J/A)
- Perform settings with the Power Mac power

supply off.

- The setup screen automatically disappears

approximately 30 seconds after the last command.

1. After connecting the power cord, turn on the

monitor’s main power.

2. Press the   button and   button simultaneously,

and while doing this press the POWER button
(i.e. turn the power on).

MAC DIGITAL

INPUT-2

OK    [ MENU ]

ON

OFF

3. Set to "ON" with the     buttons.

- Do not set to [ON] if you are not using a Belkin

ADC-DVI adapter, as this may result in
incorrect display.

4. Press the MENU button.

This completes setting.

Display cable
(purchased separately)

RGB output terminal

DVI-I input terminal

When the accessory audio cable is connected to
the audio output terminal of the computer, the
sound of the connected computer is output from
the display speakers. You can also use the
headphone jack of the display.

- If you plan to use a commercially available cable,

obtain one with no resistance.

Headphones (commercially available) can be
connected.

Notes:
- When the headphones are connected, no sound

can be heard from the monitor speakers.

Audio input
terminal

Audio cable

Audio output terminal

Headphone
terminal

Headphones

1. Turn on the main power of the monitor.

- When switching the main power switch on and

off, always wait for an interval of at least 5
seconds. Rapid switching may result in
malfunction.

2. Press the monitor's POWER button.

The power LED will light up orange.

Power terminal

Power cord

AC outlet

3. Turn on the computer.

When a signal is input from the computer, the
power LED lights up green, and the screen is
displayed (After power is turned on, it may take a
little time until the screen is displayed.)
- If the input terminal to which the computer is

connected has not been selected, the screen
will not be displayed. If necessary, perform
input terminal switching.

Notes: (when using an analog signal)
- If using the monitor for the first time or after

having changed the system settings during use,
perform an automatic screen adjustment (p. 18).

- When connecting to a notebook, if the notebook

computer's screen is set so that it is displaying at
the same time, the MS-DOS screen may not be
able to display properly. In this case, change the
settings so that only the monitor is displaying.

Use the INPUT button to switch between signal
input terminals.

INPUT-1

<ANALOG>

INPUT

INPUT-2

<ANALOG>

INPUT-2

<DIGITAL>

Main power switch

Turn on the
computer power
supply.

Press power button

Analog RGB input terminal

DVI-I input terminal

(digital)

DVI-I input terminal

(analog)

1. Turn the computer off.
2. Press the monitor's POWER button.

The Power LED will disappear.

If the monitor will not be used for a long time, turn
off the main power switch of the monitor, and
remove the power plug from the outlet.

Turn the compu-
ter off

Press power button

For analog signal
1. First perform an automatic adjustment. (p. 18)
2. Perform manual adjustment where necessary.

(p. 19)

The monitor can generally be used without
adjustment. If necessary perform manual
adjustment. (p. 22)

Note:
- All adjustments will be saved even after turning

the power off.

All adjustment values can be returned to their
original ex-factory values in one command.
1. Turn off the monitor power.
2. Press the MENU button and the SELECT button

simultaneously, and while doing this press the
power button (i.e. turn the power on).
Continue to press the button until [ALL RESET]
appears on the screen. Reset is complete when
the displayed message disappears.

Notes:
- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.

The adjustment values of the analogue signal
time’s ADJUSTMENT menu can be returned to
their original ex-factory values.
1. Turn on the monitor power.

2. Press the MENU button and the   button

simultaneously.
When [RESET] appears on the screen, the reset
is complete.

Notes:
- It is not possible to reset values when the

adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.

By disabling the control buttons (i.e. setting the
lock) any attempted changes to adjusted values
will be voided.
1. Turn off the monitor power.
2. While pressing the MENU button, press the

power button (i.e. turn the power on).
Continue to press the button until [ADJUSTMENT
LOCKED] appears on the screen.The lock is set
when the message is displayed.

Notes:
- When the lock is in place, all buttons other than

the power button are disabled.

1. Turn off the monitor power.
2. While pressing the MENU button, press the

power button (i.e. turn the power on).
Continue to press the button until [ADJUSTMENT
UNLOCKED] appears on the screen.The lock is
released when the message is displayed.

Carry out the commands without the On Screen
Display (OSD) Menu displayed. If the OSD Menu is
displayed, press the MENU button (several times
may be required) and begin when the OSD Menu
has disappeared.
1. Without the OSD Menu being displayed, push the

 or the   button.

VOLUME

BRIGHT

11
31

SELECT     [ SELECT ]

2. Check that "BRIGHT" is selected.

If it is not selected, press the SELECT button and
select "BRIGHT".

3. Adjust by pressing the   button (darker) or 

button (lighter).

Notes:
- On Screen display for adjustment disappears

several seconds after the last operation.