DOWNLOAD Sharp LL-H1513 (serv.man19) Service Manual ↓ Size: 1.26 MB | Pages: 32 in PDF or view online for FREE

1

2

3

4

5

6

8

11

14

10

15

7

12

13

9

To switch between the signal’s input terminals. (Analogue RGB input terminal 

↔ DVI-I input terminal)

This button is used to pop-up, select and close the OSD (On Screen Display) Menu.

This button is used to select menu options when the OSD Menu is displayed.

When the OSD Menu is displayed:

These buttons are used to increase or decrease the value of a selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust volume and backlight brightness .

This LED is lit green when in use and orange when in power-saving mode.

The computer’s digital RGB output terminal or analogue RGB output terminal can be connected here.
For a digital signal input, it can be connected to a computer with a DVI-compatible output terminal
(DVI-D24 pin or DVI-I29 pin) and which has XGA output ability. (Depending on the computer to be
connected, correct display may or may not be possible.)
Separately sold cables are necessary for connection.

To connect to a digital RGB output terminal: Digital signal cable (model name: NL-C01E)
To connect to an analog RGB output terminal: Analog signal cable (model name: NL-C02E)

The analog signal cable is connected here.The analog signal cable included should be used.

A computer’s audio output terminal can be connected here. The audio cable included should be used.

By connecting a security lock (commercially available) to the security lock anchor, the monitor is fixed
so that it cannot be transported. The security slot works in conjunction with Kensington Micro Saver
Security Systems.

Headphones (commercially available) can be connected here.

Note: Never block the ventilation openings as this may lead to overheating inside the monitor and
result in malfunction.

- Pressure from hands on the LCD panel could

cause damage.

- Be careful not to allow your fingers to be

pinched.

Adjust to an easy to view height.

60mm

Adjust to an easy to view angle.

30

5

45

45

The display can be rotated for a long height or
width to suit the displayed content.
- Before rotating, move the display to its

uppermost position. If the display is rotated while
it is set low, it will contact the stand and could
lead to damage.

- The display can only be rotated through a range

of 90°. Applying excessive force may cause
malfunction.

- Do not apply excessive force when the cable is

connected.

To set to long height
Gently turn in the clockwise direction (to 90°).

To set to long width
Gently turn in the counterclockwise direction (to
90°).

Note:
- The orientation of the display can be changed

using Pivot Software. (p. 33)

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to overly bend the cable or add

extension cords as this could lead to a
malfunction.

If necessary, excess cable can be housed in the
stand.

1. Remove the cover.

Gently pull the top of the cover towards yourself.

2. Run cable along the back of the stand.

- If the display is to be rotated, first house the

cables with the display in the long height
position, so there is sufficient length when the
display is turned.

3. Refit the cover.

Be careful not to pinch the cable.

- If the cover is hard to refit, do not force it.

Check whether cables are trapped.

- If the display is to be rotated, first house the

cable, and then check while gently turning the
display. If it cannot be turned, rehouse the cable
with sufficient slack. (If there is insufficient cable
length, rotation will be impossible. Forcing
rotation may cause cable disconnection.)

Connect the accessory analog signal cable to the
analog RGB input terminal of the display, and the
analog RGB output terminal of the computer.

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then
tighten the screws at both sides.

If connecting to a D-sub 15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter
(commercially available) to the analog signal
cable.

The separately sold display cable enables
connection between the DVI-I input terminal on the
display and the digital or analog RGB output
terminal of the computer.

When connecting to a digital RGB output
terminal:
- Use a digital signal cable (model name: NL-

C01E).

- For a digital signal input, it can be connected to

a computer with a DVI-compatible output
terminal (DVI-D24 pin or DVI-I29 pin) and which
has XGA output ability. (Depending on the
computer to be connected, correct display may
or may not be possible.)

When connecting to an analog RGB output
terminal:
- Use an analog signal cable (model name: NL-

C02E).

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then
tighten the screws at both sides.

Set the monitor as follows when establishing a
digital connection with a Power Mac using an
ADC-DVI adapter made by Belkin. (Operation has
been checked with the Power Mac G4 M7627J/A)
- Perform settings with the Power Mac power

supply off.

- The setup screen automatically disappears

approximately 30 seconds after the last
command.

1. After connecting the power cord, turn on the

monitor’s main power.

Analog signal cable

Macintosh conversion adapter

Analog RGB output
terminal

Analog RGB input
terminal

Display cable
(purchased separately)

RGB output terminal

DVI-I input terminal