DOWNLOAD Sharp LL-H1513 (serv.man19) Service Manual ↓ Size: 1.26 MB | Pages: 32 in PDF or view online for FREE

640 x 480

800 x 600

1024 x 768

720 x 400
640 x 480
832 x 624

1024 x 768

31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
31.5kHz
35.0kHz
49.7kHz

60.2kH

60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
70Hz

66.7Hz
74.6Hz

75Hz

25.175MHz

31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz

78.75MHz

28.3MHz
30.2MHz
57.3MHz
80.0MHz

- Recommended resolution is 1024 x 768.
- All are compliant only with non-interlaced.
- For a digital signal input, it can be connected to a computer with a DVI-compatible output terminal

(DVI-D24 pin or DVI-I29 pin) and which has XGA output ability. (Depending on the computer to be
connected, correct display may or may not be possible.)

- Frequencies for Power Macintosh is reference values. To connect, another adapter (commercially

available) may be required.

- If the monitor is receiving timing signals that are not compatible, [OUT OF TIMING] will appear. Follow

your computer’s instruction manual to set the timing so that it is compatible with the monitor.

- If the monitor is not receiving any signal (synch signal), [NO SIGNAL] will appear.

(Mini D-sub connector with 15 pins)

1

Red video signal input

2

Green video signal input

3

Blue video signal input

4

GND

5

GND

6

For red video signal GND

7

For green video signal GND

8

For blue video signal GND

9

DDC/+5V

10 GND
11 N.C.
12 DDC data
13 For Hsync signal input
14 For Vsync signal input
15 DDC clock

(DVI-I connector with 29 pins)

No. Function

No. Function

1

TMDS data 2-

16

Hot plug detection

2

TMDS data 2+

17

TMDS data 0-

3

TMDS data 2/4 shield

18

TMDS data 0+

4

N.C.

19

TMDS data 0/5 shield

5

N.C.

20

N.C.

6

DDC clock

21

N.C.

7

DDC data

22

TMDS clock shield

8

23

TMDS clock +

9

TMDS data 1-

24

TMDS clock -

10 TMDS data 1+

C1

Analogue red image signal

11 TMDS data 1/3 shield

C2

Analogue green image signal

12 N.C.

C3

Analogue blue image signal

13 N.C.

C4

14 +5V

C5

Analogue GND

15 GND

Analogue vertically synchronised
signal

Analogue horizontally synchro-
nised signal

The monitor is based on the VESA DPMS*

1

 and the DVI DMPM*

2

 standards.

To activate the monitor's Power Management function, both the video card and the computer must
conform to the VESA DPMS standard and the DVI DMPM standard.

*

1

 DPMS: Display Power Management Signalling

                                                   *Not using USB hub

*

2

 DMPM: Digital Monitor Power Management

                                      *Not using USB hub

This monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for carrying out Plug & Play functions on the monitor or PC. It transfers informa-
tion such as degree of resolution between the monitor and PC. You can use this function if your PC is
DDC compliant and if it is set so that it can detect the Plug & Play monitor.
There are many varieties of DDC due to the differences between systems. This monitor works with DDC1
and DDC2B.

DPMS mode

Screen

Power

H-sync V-sync

consumption

ON

Display on

33W*

Yes

Yes

STANDBY

No

Yes

SUSPEND Display off

3W

Yes

No

OFF

No

No

DMPM mode

Screen

Power

consumption

ON

Display on

33W*

OFF

Display off

3W

Depending on the computer or OS, it may be
necessary to use the computer to operate the
installation of monitor set-up information etc. If so,
follow the steps below to install the monitor set-up
information. (Depending on the type of computer or
OS, command names and methods may differ.
Please follow the computer’s own operation manual
while reading this.)

About the ICC profile
An ICC (International Color Consortium) profile
is a file that describes the color characteristics
of the LCD monitor. By using an application that
works together with an ICC profile, a high color
resolution can be realized.
- Windows98/2000/Me/XP all use the ICC

profile.

- When installing Windows98/2000/Me/XP set-

up information (described below), the ICC
profile is also installed. If you would like to
install  the ICC program only, please refer to
Installing the ICC profile on page 30.

- When using an ICC profile, set  [COLOR

MODE] and [WHITE BALANCE] to [STD], and
set [HUE] and [SATURATION] to [0].

Installing monitor set-up information into
Windows95.
This explanation assumes that the CD-ROM drive
is "D drive".
1. Load the accessory CD-ROM into the D drive

of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy

manufacturer's files from:] is [D:] then click [OK].

6. Confirm that the monitor details are selected,

and click [OK].

7. Check that the monitor details are displayed,

then click [Apply].

8. Click [OK], and close the window.

Installing monitor set-up information into Win-
dows98, and setting the monitor's ICC profile as a
predetermined value.
This explanation assumes that the CD-ROM drive
is "D drive".

If the "Add new Hardware Wizard" has appeared:
1. Load the accessory CD-ROM into the D drive

of the computer.

2. Click [Next].
3. Check [Display a list of all the drivers in a

specific location, so you can select the driver
you want.], then click [Next].

4. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [D:], and click [OK].

5. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish]. If the "Add
New Hardware Wizard" appears, repeat the
installation commands beginning from 2 above.

If the "Add New Hardware Wizard" has not ap-
peared:
1. Load the accessory CD-ROM into the D drive

of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Click [Next].
7. Click on [Display a list of all the drivers in a

specific location, so you can select the driver
you want.], then click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [D:], and click [OK].

9. Confirm that the monitor details are selected,

then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.

Installing monitor set-up information into Win-
dows2000, and setting the monitor's ICC profile as
a predetermined value.
This explanation assumes that the CD-ROM drive
is "D drive".
1. Load the accessory CD-ROM into the D drive

of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. Click on [Properties], [Driver] and [Update

Driver].

6. When [Upgrade Device Driver Wizard] appears,

click [Next].

7. Check [Display a list of the known drivers for

this device so that I can choose a specific
driver] and click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [D:], and click [OK].

9. Select the monitor from the list displayed and

click [Next].

10. Click [Next], confirm that the monitor's name

appears on the screen, and click [Finish]. If
[The Digital Signature Not Found] appears, click
[Yes].

11. Click on [Close].
12. Click [OK], and close the window.

Installing monitor set-up information into
WindowsMe, and setting the monitor's ICC profile
as a predetermined value.
This explanation assumes that the CD-ROM drive
is "D drive".

If the "Add new Hardware Wizard" has appeared:
1. Load the accessory CD-ROM into the D drive

of the computer.

2. Check [Specify the location of the driver

[Advanced]] and click [Next].

3. Check [Display a list of all the drivers in a

specific location, so you can select the driver
you want.], then click [Next].

4. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [D:], and click [OK].

5. Select the monitor details from the list, then

click [Next], [Next], and [Finish]. If the "Add new
Hardware Wizard" appears, repeat the
installation commands beginning from 2 above.

If the "Add New Hardware Wizard" has not ap-
peared:
1. Load the accessory CD-ROM into the D drive

of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].
4. Click on [Settings], [Advanced] and [Monitor].
5. In [Options], check [Automatically detect Plug &

Play monitors] and click on [Change].

6. Check [Specify the location of the driver

[Advanced]] and click [Next].

7. Check [Display a list of all the drivers in a

specific location, so you can select the driver
you want.] and click [Next].

8. When [Models] is displayed, click on [Have

disk], confirm that [Copy manufacturer's files
from:] is [D:], and click [OK].

9. Select the monitor details, then click [Next],

[Next], and [Finish].

10. Check that the monitor details are displayed,

then click [Apply].

11. Click [OK], and close the window.