DOWNLOAD Sharp LL-151-3D (serv.man2) Service Manual ↓ Size: 1.84 MB | Pages: 127 in PDF or view online for FREE

The 3D image on the display appears blurred
and doubled.
- Confirm if the 3D display compatible software is

running.

- For software supporting SHARP 3D Technology

- Press the 3D button to enter 3D mode (the

power LED changes to blue).

- Confirm that screen resolution is set to

1024 x 768.

- When two or more users are logged on, let all

users log off, and then log on as the user who
logged on first.

- The best viewing position in 3D mode is the

position where the entire red strip (or its bottom)
appears darkest. Move your head slightly
up/down, right/left, and forward/backward to
adjust your position.

When it is in 3D mode, the screen appears a
little darker.
- In 3D mode, the screen appears a little darker

than in 2D mode. (This is not a malfunction.)

The mode cannot be switched to 3D mode by
pressing the 3D button.
- Does the current software support SHARP 3D

Technology? If you are using software that does
not support SHARP 3D Technology, refer to the
operation manual of the software.

Model name

LL-151-3D

LCD display

38 cm measured diagonally TFT 3D  LCD module

Resolution (max.)

XGA 1024 x 768 pixels
(In 2D mode only. In 3D mode, the actual
resolution is half because the horizontal pixels
are divided between right and left eyes.)

Displayable colors (max.)

Approx.16.19 million colors (6 bit + FRC)

Brightness (max.)

2D mode: 370 cd/m

2

3D mode: 140 cd/m

2

(The screen brightness deteriorates over time.
Constant brightness cannot be maintained.)

Dot pitch

0.297 (H) x 0.297 (V) mm

Contrast ratio

500:1

Angle of visibility (2D mode)

Left-right 130°; up-down 115°
(contrast ratio > 10)

Screen display size

Horizontal 304.1 mm x Vertical 228.1 mm

Video signal

Analog: Analog RGB (0.7 Vp-p) [75

Ω]

Digital: DVI standard based on 1.0

Sync signal

Separate Sync (TTL level: +/-)

Expansion compensation

Digital scaling (Enlarges VGA/SVGA etc. to full
screen size.)

Plug & Play

VESA DDC2B compatible

Power management

VESA: based on DPMS
DVI: based on DMPM

Speaker output

1 W + 1 W

Input signal terminal

Digital/Analog: DVI-I 29 pin

PC connection terminal for 2D/3D selection

USB

Audio input terminal

Mini stereo jack

Headphone terminal

Mini stereo jack

Height adjustment

Adjustment range: approx. 60 mm

Screen tilt

Upward approx. 0-30°; downward approx. 0-5°

Screen swivel

Approx. 45° from the center to the left and
approx. 45° from the center to the right.

Power supply

100-240 VAC, 50/60 Hz (Uses special AC
adapter, type NL-A56J of Sharp Corporation)

Temperature of operating environment

5-35°C

Power consumption

25 W (with no audio input)
(29 W maximum, 2 W when in power-saving
mode) (Uses special AC adapter)

Dimensions

Approx. 352 (W) x 185 (D) x 370-430 (H) mm

Weight

Approx. 5.3 kg (approx. 3.4 kg excluding stand)
(excluding signal cable and AC adapter)

(Units: mm)

352

185

370

430

298

238

64

- Digital signal cable: approx. 2.0 m
- Analog signal cable: approx. 2.0 m
- Audio cable: approx. 2.0 m
- USB cable: approx. 2.0 m
- Special AC adapter:

 Approx. 2.0 m

Note:
- As a part of our policy of continuous

improvement, SHARP reserves the right to make
design and specification changes for product
improvement without prior notice. The
performance specification figures indicated are
nominal values of production units. There may
be some deviations from these values in
individual units.

Approx. 125 (W) x 60 (D) x 33 (H) mm

- Recommended resolution is 1024 x 768.
- All are compliant only with non-interlaced.
- A computer with an output terminal conforming to

DVI (DVI-D 24 pin or DVI-I 29 pin) and with XGA
output capability can be connected here.
(Depending on the type of computer to be
connected, the display may not work correctly.)

- If the monitor is receiving timing signals that are

not compatible, [OUT OF TIMING] will appear.
Follow your computer's instruction manual to set
the timing so that it is compatible with the
monitor.

- If the monitor is not receiving any signal (synch

signal), [NO SIGNAL] will appear.

- Recommended resolution is 1024 x 768.
- All are compliant only with non-interlaced.
- Frequencies for Power Macintosh are reference

values. To connect, another adapter
(commercially available) may be required.

- If the monitor is receiving timing signals that are

not compatible, [OUT OF TIMING] will appear.
Follow your computer's instruction manual to set
the timing so that it is compatible with the
monitor.

- If the monitor is not receiving any signal (synch

signal), [NO SIGNAL] will appear.