DOWNLOAD Sharp UP-3301 (serv.man9) Service Manual ↓ Size: 4.89 MB | Pages: 96 in PDF or view online for FREE

UP-3301VS

DIAGNOSTICS SPECIFICATIONS

– 31 –

To enter numbers, the numeric key panel is displayed in the lower
part of the screen. 

When the IPL switch is not in the writing MODE, the following mes-

sage is displayed.

3

How to terminate

Press the Touch panel to terminate.

Data transmission is checked in the system already established. The
system is composed of one master machine and a max of 63 satellite

machines. 

Note when starting the test:

•  When checking the set in which the LAN setting has been completed,

disable the LAN setting before starting this check.

• When testing the system already established, disconnect the LAN

cable of the sets not subject to test, or disable the LAN setting. Leav-

ing LAN enabled may cause data to be destroyed.

• The transmission test setting must be performed after disabling the

LAN setting of all the sets in the system. For the transmission check

setting, first, set the satellite machines, then set the master machine.

UP-3301 DIAG uses private IP address. This DIAG assigns Private IP

addresses to 64 terminal numbers to simplify the test as shown below.

When performing data transmission check, be sure to physically discon-
nect other network where these IP addresses are set. 

TERMINAL NO.1 = 192.168.0.1

TERMINAL NO.2 = 192.168.0.2
. . . . .

TERMINAL NO.63 = 192.168.0.63

TERMINAL NO.64 = 192.168.0.64

1

How to set

i.

Satellite machine setting

In the menu screen, select "Data Trans. (SA)". Following screen
appears. Numeric key panel to enter numbers is displayed in

the lower part of the screen.

Press the terminal No. (2 digits number between 1~64) of the

machine to be checked and touch the Enter key.

The following screen appears.

ii.

Master machine setting

In the menu screen, select "DATA Trans. (MA)". The following
screen appears. Numeric key panel to enter numeric character
is displayed in the lower part of the screen.

Press the terminal No.(2 digits number among 1~64) of the
machine to be checked and Enter key. 

The following screen appears. The numeric key panel to enter
numeric characters is displayed in the lower part of the screen.

Press the terminal No. (2 digits number among 1~64) of the sat-
ellite machine to be connected to the test machine. The
numeric key panel to enter numeric characters is displayed in
the lower part of the screen.

When checking with two or more satellite machines connected,
repeat the entry for the terminal No. (2 digits, 1~64) and touch
ENTER key. To execute the checking, touch the ENTER key
without entering the terminal No. You can also enter the termi-
nal No. with range designating function without entering all ter-
minal No. After entering the first terminal No. and last terminal
No. of the satellite machine, touch ENTER key. For example,
when you want to enter the terminal No. 5~63 of the satellite
machine, touch "0515" and ENTER key.

The following screen appears.

Do not assign the same terminal No. to different machines
(master/satellite).

When you designate terminal No. with range designating func-
tion, the terminal No. used in the master machine is excluded
from the designated terminal number of the satellite machine.

After completing the above setting, data transmission test
starts.

MAC ADDR&FIRM Write

CHANGE IPL SW!!

Data Trans. (SA)

INPUT SA T-NO :

←

Enter one number out of 1 to 64. 

ENTER

0

CANCEL

4

7

2

1

5

8

3

6

9

CL

Data Trans. (SA)

INPUT SA T-NO : XX

←

Displays the entered terminal numbers 

    of the satellite machine.

DATA SEQ NO. : 0000

Data Trans. (MA)

INPUT MA T-NO : 

←

Enter one number out of 1 to 64.

Data Trans. (MA)

INPUT MA T-NO : XX

←

Displays the entered terminal number of 

    the master machine.

INPUT SA T-NO : 

←

Enter one number out of 1 to 64.

Data Trans. (MA)

INPUT MA T-NO : XX

←

Displays the entered terminal 

    number of the master machine.

INPUT SA T-NO : XX (or XXXX)

←

Displays the entered terminal

    numbers of the satellite machine.

Data Trans. (MA)

INPUT MA T-NO : XX

←

Displays the entered terminal number of 

    the master machine.

INPUT SA T-NO : XX

←

Displays the entered terminal number of 

    the satellite machine.

 XX XX XX XX XX XX (or XXXX)

When multiple terminal number 
of the satellite machine are 
entered, all of them will be dis-
played.

DATA SEQ.NO. : 0000

UP-3301VS

DIAGNOSTICS SPECIFICATIONS

– 32 –

2

 Check content

i.

Data composed of 2 byte sequence No. and 254 byte AAH data

in the following format are transmitted from the master machine

to the satellite machine. The master machine displays the

sequence No. 

Test data format (1 packet : 256 byte)

ii.

The satellite machine sends back the received data to the mas-

ter machine. The satellite machine displays the received

sequence No.

iii. After receiving the data, the master machine checks the

sequence No. and 254 byte AAH data. In case of an error, the

error code is displayed and the test is completed. If multiple sat-

ellite machines are connected, the step i and ii above operation

are repeated. If data transmission with all the satellite machines

are normally completed, the master machine increments the

sequence No.

Repeat step i and iii. 

3

 Error display 

Description of the error codes are shown below. (comply with TCP/IP

HDNLER)

4

 How to terminate

Touch PANEL key to terminate the check.

Read check of the optional UP-E12MR2 is performed.

The test program reads the magnetic card of ISO 7811/1-5 standard

and displays the data. When the Touch panel is pressed, the display
returns to the diagnostics menu.

1

Check content

The test program reads tracks 1 and 2 of the magnetic card of ISO

7811/1-5, and displays the data in ASCII code. 

2

Display

XXXXX shows the data read by the MCR. Incase of an error, the
error code is displayed as shown below.

3

Terminating procedure

Press the Touch panel to terminate the check. 

This diagnostics is used to check the drawer open and sensors. 

The following menu is displayed. Press the position of the operation you

want to perform to execute individual Diag programs.

Pressing the CANCEL key returns the screen to the Diag MAIN menu.

Data Trans. (MA)

INPUT MA T-NO : XX

INPUT SA T-NO : XX

 XX XX XX XX XX XX

 XX XX XX XX XX XX (or XXXX)

DATA SEQ.NO. : 0000

TCP/IP ERROR : XX 

←

Displays ERROR CODE.

01

Improper command (except when transmission)

02

No data received.

03

Received data present. 
Received data remained.

04

Remote machine not ready (when sending)
"NTDY" is sent back because the remote machine is not
ready for reception.

05

Received buffer full (when sending)
The controller’s receive buffer of the remote machine is full.

06

Re-send error (when sending)
Excess retrying (5 times) for no response

07

Collision error (when sending)
In a collision circumstance, excess in retry times (16 times) for
re-collision after a random (0~255ms) interval.

08

Line busy time out. 
Transmission can not be made due to the communications
between multi-station, and it causes time out in data send wait
time.

09

Excess of allowed receive size (when receiving)
Received buffer size is insufficient.

0A

Hardware error
Improper interface (LAN controller etc.)

XX

XX

AA

AA

AA

AA

AA

AA

256

255

254

5

4

3

2

1

Byte

XXXX
AA

: Sequence No. (2byte: 4digits of binary decimal numbers)
: Transmission data (AAH) x 254 bytes

MCR (Magnetic Card Reader) Check

TRACK1:

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

TRACK2:

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Magnetic Card Reader Check

TRACK1:BUFFEREMPTY

- Displayed when TRACK1 empty

code is sent back.

TRACK1:MCRERROR

- Displayed when  TRACK1 error

code is sent back.

TRACK2:BUFFEREMPTY

- Displayed when TRACK2 empty

code is sent back.

TRACK2:MCRERROR

- Displayed when  TRACK2 error

code is sent back.

Drawer 1 Check

Cancel

Drawer Diagnostics

Drawer 2 Check

UP-3301VS

DIAGNOSTICS SPECIFICATIONS

– 33 –

1

Check content

The solenoid of drawer 1 is turned on, and the drawer open sensor
value is sensed at every 100ms, and the state is displayed.

2

Display

3

Terminating procedure

Press the Touch panel to terminate the check. 

1

Check content

The solenoid of drawer 2 is turned on, and the drawer open sensor
value is sensed at every 100ms, and the state is displayed.
The display and the terminating procedure are the same as Drawer
1 Check. 

I/F loopback and printing tests of the built-in printer are performed.
The following menu appears. Press the name of the test you want to
perform to execute its Diag program. When the Diag program is termi-
nated, the screen returns to the Printer Diagnostics menu. Pressing the
CANCEL key returns to screen to the Diag Menu.

1

Check content

A LOOPBACK test on the built-in printer (UP-T80BP) interface
(logic channel 7 of RS232) is performed and the result is displayed.
The test itself is the same as that for the RS232. The difference in
test specifications is as follows: The loopback signals are for ER-
DR, RS-CS, TXD-RXD only and the following LOOPBACK-Connec-
tors are required.

Wiring diagram of loopback connectors 

(UKOG-2356BHZZ)

2

Indication

The indication is the same as that for RS232 DIAGNOSTICS.

3

End

Press the PANEL to end the program.

1

Check

Send the signal to generate a receipt (by DIAG COMMAND) to the
UP-T80BP.

Check of the EFT (ER-02EF) is performed.

Select the EFT Diag, and turn of  the power supply after that.

Set all the bits of DIPSW1 to “off”, then turn off the power supply of main
unit. The EFT check is performed automatically.

1

Check content

i.

Executes the LOOP BACK TEST to EFT connector about ER-

DR, ER-CT and RS-CS signals.

ii.

Executes the DIPSW1 check by turning on the 1-8 bit of

DIPSW1 in order.

iii. When normal, SUM CHECK of EFT ROM is performed auto-

matically, and WRITE/READ check is performed to RAM.

2

Display (Normal)

3

Display (Error)

4

End

Pless the PANEL to end the program.

Drawer1 Check

Drawer Open Sensor

: OPEN (or CLOSE)

Loop Back Check

Printer Print Check

Cancel

Printer Diagnostics

1pin

2pin

3pin

4pin

5pin

6pin

7pin

8pin

9pin

CD

RD

SD

ER

GND

DR

RS

CS

CI

EFT Diagnostics

DIAGO (SELF TEST) : OK
VHI27040R

**

1

*

: OK

256K SRAM

: OK

In Loop Back Error

ER-DR LOOP ERROR
ER-CI LOOP ERROR
ER-CS LOOP ERROR

In Self Test Error

DIP SW ERROR

In Self Test Error

VHI27040R

**

1

*

: ERROR

256K SRAM

: ERROR

UP-3301VS

CIRCUIT DESCRIPTION

– 34 –

Drawer x 2

RS232 x 2

CPU

H8/510

MPCA8

Customer display

MCR

SRAM

2MB

OPC2

EXT.SLOT

(80pin x 2)

RAMCN

(72pin)

CKDC9

VCC

+24V

+12V

LCD

640 x 480 dots

DRIVER

DRIVER

DRIVER/
RECEIVER

VGA

CONTROLLER

MN89303A

BRIGHTNESS
CONTROL

INVERTER

CONTRAST
ADJUSTMENT

POWER SUPPLY

VRAM

(DRAM 512K)

UPE10IN

Compatible

FLASH

RAM

4MB

(NOR)

PRINTER (UP-T80BP)

Clerk SW

TCP/IP

TOUCH

CONTROLLER

x 2