DOWNLOAD Sharp UP-3301 (serv.man9) Service Manual ↓ Size: 4.89 MB | Pages: 96 in PDF or view online for FREE

UP-3301VS

SERVICE PRECAUTION

– 15 –

No

Procedure on P.C. side

No

Procedure on UP-3301 side

1

Install “UTL33.EXE” on the P.C.

2

Turn OFF the power.

3

Select “IPL Mode”.

Set the “IPL Switch” of UP-3301 to “ON”.

4

Turn ON the power.

5

Starting of “IPL Mode”.
The UP-3301 displays

“IPL from Serial I/O”

6

Connect P.C. and UP-3301 via RS232. 

7

Execute “UTL33.EXE” on P.C.

Operation:

(“3301_1.ROM” and “3301_2.ROM” are file name of S-type
ROM object.)

8

Program data is sent to UP-3301 automatically.

8

Program data is received from P.C. automatically.

The UP-3301 displays

9

“UTL33.EXE” is completed.

P.C. shows

“Completed.”

9

The UP-3301 displays

“Completed.”

10

Turn OFF the power.

11

Select “Normal Mode”.

Set the “IPL switch” to “OFF”.

12

Execute the “Service Reset” on UP-3301.

IPL SW

ON

IPL from IR
Connected IRDA 115200
21 22 23 24 25 26 27 28

IPL from Serial I/O
Connected IRDA 115200
21 22 23 24 25 26 27 28
29 2A 2B 2C 2D 2E 2F
Completed.

IPL from Serial I/O
Connected IRDA 115200
30 31 32 33 34 35 36 37
38 39 3A 3B 3C 3D 3E 3F
Completed.

UP-3301VS

SERVICE PRECAUTION

– 16 –

No

Procedure on P.C. side 

No

Procedure on UP-3301 side

1

Install “UTL33.EXE” on the P.C.

2

Enter the SRV mode. Then turn OFF the power or UP-3301.

3

While pressing the On-Line key, tum ON the power of UP-3301.
Keep pressing the On-Line key, and then press the Feed key
also. (Don’t move a finger from the On-line key.)

4

UP-T80BP enters into LOGO mode.

UP-T80BP prints out 

“

****************

”.

5

Go  into  “UP-T80BP Utility mode”.

Select “6 UP-T80BP Utility” in SRV mode.

6

Starting of “UP-T80BP Utility mode”.

UP-3301 shows

7

Connect P.C. and UP-3301 via RS232 (CH2). 

8

Execute “UTL33.EXE” on P.C.

Operation:

(“LOGO.BMP” is a file name of Bit-Map image.)

9

Program data is sent to UP-3301 automatically.

9

Program data is received from P.C. automatically. 

10

“UTL33.EXE” is completed.

P.C. shows

“Completed.”

10

UP-3301 shows

“Completed.”

And UP-T80BP prints out the LOGO image.

11

Touch “OK” button.

12

Touch “EXIT” button.

13

Turn OFF the power of UP-3301.

14

Execute “Master Reset” on UP-T80BP.

No

Procedure on P.C. side

No

Procedure on UP-3301 side

1

Install “UTL33.EXE” on the P.C.

2

Turn OFF the power of UP-3301.

3

Select “IPL Mode” on UP-T80BP.

Set the Bit 1 of DipSwitch 2 to “ON” to enter “IPL Mode”.

4

While pressing both the Feed key and the On-Line key, turn ON
the power of UP-3301.

The ERROR Lamp and the On-line Lamp of UP-T80BP is
blinking.

UP-T80BP Utility

EXIT

UP-T80BP Utility

Normal mode

EXIT

UP-T80BP Utility

Normal mode

EXIT

Complete

OK

IPL SW

ON

IR Filter

UP-3301VS

SERVICE PRECAUTION

– 17 –

“UTL33.EXE” is a utility program on P.C. - a program that sends the
application program data of UP-3301, the image data of the Logo stamp
of UP-T80BP or the application program data of UP-T80BP in order to
replace them.

UTL33  [-Fn]  [-Cn]  filename [filename ...]

filename

Specifies the name file which you want to send.

-Fn

Specifies the function. Valid values for n are in the range 1 through 3.
1: UP-3301 IPL
2: UP-T80BP LOGO STAMP
3: UP-T80BP IPL
Normally, UTL33.EXE takes the suitable function automatically.
If the automatic selection does not work correctly, please use this
switch.

-Cn

Specifies the number of the serial (COM) port. Valid values for n are
in the range 1 through 2.
The default value is 1 (COM1).

For UP-3301 IPL.

UTL33  3301_1.ROM  3301_2.ROM

For UP-T80BP LOGO STAMP (To use COM2).

UTL33  -C2  LOGO.BMP

For UP-T80BP IPL (To use the switch “-F”).

UTL33  -F3  80BP.ROM.

5

UP-T80BP enters into IPL mode when the Feed key is pressed.
(UP-T80BP clears the application program which is in its own
flash ROM.)

The ERROR Lamp is blinking and the On-Line Lamp is turned off.

6

UP-T80BP waits the application program data.

The ERROR Lamp is turned off and the On-Line Lamp is
turned on.

7

Enter “UP-T80BP Utility” mode.

Select “6 UP-T80BP Utility” in SRV mode

8

Starting of “UP-T80BP Utility” mode.
UP-3301 shows

9

Connect P.C. and UP-3301 via RS232 (CH2).

10

Execute “UTL33.EXE” on P.C.

Operation:

(“T80BP.ROM” is a file name of S-type object.)

11

Program data is sent to UP-3301 automatically.

11 

Program data is received from P.C. automatically.

The On-line Lamp of UP-T80BP starts blinking.

12

“UTL33.EXE” is completed.
P.C. shows

“Completed.”

12

UP-3301 shows

“Completed.” 

The On-line Lamp of UP-T80BP stops blinking.

13

Touch  “OK” button.

14

Touch  “EXIT” button.

15

Turn OFF the power of UP-3301.

16

Select “Normal Mode” on UP-T80BP.

Set the Bit 1 of DipSwitch 2 to “OFF” to enter “Nomal Mode”.

17

Execute “Master Reset” on UP-T80BP.

No

Procedure on P.C. side

No

Procedure on UP-3301 side

UP-T80BP Utility

EXIT

UP-T80BP Utility

EXIT

IPL mode

IPL mode

UP-T80BP Utility

- : 1 6

Complete

OK

For UP-3301 IPL

S-type ROM object file

For UP-T80BP LOGO STAMP BMP/PCX file
For UP-T80BP IPL

S-type ROM object file

UP-3301VS

SERVICE PRECAUTION

– 18 –

To solder the following parts manually, follow the conditions described
below.

•  The transparency of the touch panel is vitally important. Do not place

finger prints or moisture on the surface. When handling, use clean
gloves and masks.

• For handling, do not hold the transparent area, and do not hold the

heat seal connector section to assure reliability. 

•  Do not overlay touch panels. The edge may damage the surface. 

•  Do not put a heavy object on the touch panel.

•  Do not apply strong shocks, and do not drop.

•  When attaching the protection film, carefully check that no dirt exists. 

•  To clean dirt on the surface, use a dry, soft cloth or a cloth immersed

in ethyl alcohol.

• Check that the housing does not induce any stress to the touch

panel. 

•  Be careful not to touch the touch panel with tools. 

• The heat seal section is easily disconnected. Be careful not to apply

any stress to the heat seal section when installing. 

• The touch panel is provided with an air groove to make the external

and the internal air pressure equal to each other. If water or oil is put
around the air groove, it may penetrate inside. Be careful and keep
the air groove away from water and oil. 

• Input is performed with fingers. Do not use hard objects to input

entries.

•  The LCD elements are made of glass. BE careful not to expose them

to a strong mechanical shock. Use extreme care not to break them.

• If the LCD element is broken and the liquid is seeps, do not lick it. If

the liquid comes in contact with your skin or clothes, immediately
clean with soap. 

•  Use the unit under the rated conditions to prevent against damage.

•  Be careful not to drop water or other liquids on the display surface.

• The reflection plate and the polarizing plate can be easily scratched.

Be careful not to touch them with any hard object such as glass or
tweezers. Never hit, push, or rub the surface with hard objects.

• When installing the unit, be careful not to apply stress to the LCD

module. If excessive stress is applied an abnormal display or uneven
color may result. 

When connecting or disconnecting the following connectors, follow the

procedures below.

(1) Open the slider to the unlock position

The slider will open only up to a fixed height (about 1.2mm). If you

used force to pull up the slider further, it may be damaged.

(2) Insert the FFC

Insert the FFC firmly untill the FFC hits the bottom of the connec-

tor’s insulator.

(3) Close the slider to the lock position

Insert the FFC and then push the slider downward.

PARTS 

NAME

PARTS CODE

LOCATION

CONDITIONS FOR 

SOLDERING

Ceramic 
oscillator

RCRMZ7002RCZZ

MAIN PWB: 
X1 (8M)

270°/3sec.

RCRMZ7004RCZZ

MAIN PWB: 
X2 (7.37M)

270°/3sec.

PARTS NAME

PARTS CODE

LOCATION

FFC 
CONNECTOR

QCNCW7207RC4J

MAIN PWB: CN6
TOUCH PWB: CN5

FFC 
CONNECTOR

QCNCW7183BH2F

MAIN PWB: CN1

Slider

1.2mm

UNLOCK

FFC

FFC

CONNECTOR

FFC

CONNECTOR

FFC

CONNECTOR

FFC

Slider

LOCK