Sharp XE-A303 (serv.man6) User Manual / Operation Manual ▷ View online
7
Part
1
QUICK START GUIDE
Part
2
Part
3
Operator display
• Clerk code or Mode name
The mode you are in is displayed. When a clerk is assigned, the clerk code is displayed in the REG or
OP X/Z mode. For example, “?01?” is displayed when clerk 01 is assigned.
OP X/Z mode. For example, “?01?” is displayed when clerk 01 is assigned.
• Repeat mark
The number of repeats is displayed, starting at “2” and incremental with each repeat. When you have
registered ten times, the display will show “0”. (2
registered ten times, the display will show “0”. (2
➞ 3 ......9 ➞ 0 ➞ 1 ➞ 2...)
• Sentinel mark
When amount in the drawer reaches the amount you preprogrammed, the sentinel mark “X” is displayed
to advice you to remove the money to a safe place.
to advice you to remove the money to a safe place.
• Power save mark
When the cash register goes into the power save mode, the power save mark (decimal point) lights up.
• Function message display area
Item labels of departments and PLU/subdepartments and function texts you use, such as %1, (-) and
CASH are displayed. For the details of function texts, please refer to page 66.
When an amount is to be entered or entered, “AMOUNT” is displayed: When an amount is to be
entered, ------- is displayed at the numeric entry display area with “AMOUNT”. When a preset price has
been set with "Open & Preset" selected in department programming, the preset price is displayed at the
numeric entry display area with "AMOUNT".
CASH are displayed. For the details of function texts, please refer to page 66.
When an amount is to be entered or entered, “AMOUNT” is displayed: When an amount is to be
entered, ------- is displayed at the numeric entry display area with “AMOUNT”. When a preset price has
been set with "Open & Preset" selected in department programming, the preset price is displayed at the
numeric entry display area with "AMOUNT".
• Numeric entry display area
Numbers entered using numeric keys are displayed here.
Date and time display
Date and time appear on the display in the OP X/Z, REG, or MGR mode. In the REG or MGR mode, press
the
the
s
key to display the date and time.
Error message
When an error occurs, the corresponding error message is displayed in the function message display area.
For details of error messages, please refer “Error message table” on page 98.
For details of error messages, please refer “Error message table” on page 98.
Customer display
(Pop-up type)
(Pop-up type)
This key locks and unlocks the drawer. To lock it, turn 90
degrees counterclockwise. To unlock it, turn 90 degrees
clockwise.
degrees counterclockwise. To unlock it, turn 90 degrees
clockwise.
5
Displays
6
Drawer Lock Key
Function message display area
Clerk code or mode name
Numeric entry display area
Receipt OFF indicator
Repeat / Sentinel mark / Power save mark
SK1-1
A303_1(En) 06.7.22 9:20 AM Page 7
8
PREPARING THE CASH REGISTER
Unpack the cash register and make sure all accessories are included. For details of accessories, please refer to
“SPECIFICATIONS” section on page 99.
“SPECIFICATIONS” section on page 99.
For installing the cash register, find a stable surface near an AC outlet where the cash register will not subject to
water sources or direct sunlight.
water sources or direct sunlight.
For preparing the cash register, please follow the three steps shown below; "1 Installing the Cash Register" on
page 8, "2 Initializing the Cash Register" on page 9, and "3 Installing Paper Rolls" on page 10.
page 8, "2 Initializing the Cash Register" on page 9, and "3 Installing Paper Rolls" on page 10.
Install the cash register using the fixing angle bracket provided with the register according to the following
instruction. The fixing angle bracket prevents the register from moving when the drawer opens. By hooking the
register on the bracket, you can secure the register to the position.
instruction. The fixing angle bracket prevents the register from moving when the drawer opens. By hooking the
register on the bracket, you can secure the register to the position.
How to install the fixing angle bracket
1.
Thoroughly clean the location where the fixing angle bracket
(B) is to be placed.
(B) is to be placed.
2.
Peel off the adhesive tape on the fixing angle bracket.
3.
Hook the angle bracket onto the hook (A) that is located at the
bottom rear of the register.
bottom rear of the register.
4.
Firmly stick the fixing angle bracket to the table surface that
your cleaned above.
your cleaned above.
How to remove the register from the fixing angle bracket
1.
Lift up the front of the register and pull the register towards
you.
you.
STEP
2
1
Installing the Cash Register
A
B
A303_1(En) 06.7.22 9:20 AM Page 8
9
Part
1
QUICK START GUIDE
Part
2
Part
3
In order to operate the cash register properly, you must initialize it before operating for the first time. Follow this
procedure.
procedure.
1.
Make sure the power cord plug is not inserted into the AC outlet.
2.
Insert the manager (MA) key into the mode switch and turn it to the PGM
position.
position.
3.
While holding down both the
}
key and the
l
key, insert the plug into
the AC outlet. The buzzer will sound three times and “??? MRS. ???”
will be displayed.
will be displayed.
4.
The cash register has now been initialized. The register display will now
show “0.00” with “PGM”.
show “0.00” with “PGM”.
If the buzzer does not sound when the plug is inserted, the initialization has not been done
successfully. (This will occur when the voltage is high because you operated the cash register
before starting initialization.) Wait at least ten seconds after pulling out the plug and initialize the
cash register again.
successfully. (This will occur when the voltage is high because you operated the cash register
before starting initialization.) Wait at least ten seconds after pulling out the plug and initialize the
cash register again.
The cash register has a built-in memory protection circuit which is operated by rechargeable
batteries. Since the rechargeable batteries have been discharged, please charge the batteries for
one or two days before using the cash register for the first time. To charge the batteries, set the
mode switch to a position other than “
batteries. Since the rechargeable batteries have been discharged, please charge the batteries for
one or two days before using the cash register for the first time. To charge the batteries, set the
mode switch to a position other than “
” with the power cord plugged into the AC outlet.
Unless the batteries have been charged, all of the programmed data and sales data is not saved.
If you press a key by mistake, an error message such as “HEAD UP” or “PAPER EMPTY” may be
displayed. Press the
displayed. Press the
l
key to clear message after installing paper rolls.
2
Initializing the Cash Register
REG
OPX/Z
MGR
PGM
X1/Z1
X2/Z2
PGM
0.00
0.00
*** MRS. ***
_
A303_1(En) 06.7.22 9:20 AM Page 9
10
Precaution: The paper cutter is mounted on the printer cover. Take caution when removing and installing
the cover.
The register can print receipts and journals. For the printer, you must install the paper rolls (receipt and journal
paper rolls) provided with the register.
Install the paper rolls according to the procedure shown below with the power cord connected and the mode
switch set to the REG position:
paper rolls) provided with the register.
Install the paper rolls according to the procedure shown below with the power cord connected and the mode
switch set to the REG position:
1.
Cut off approximately one revolution of each paper roll.
Make sure each paper end is cut as per the diagram.
Make sure each paper end is cut as per the diagram.
2.
Lift up the print roller release lever
(indicated as "PULL" on it) of the
receipt side to unlock and open the
print roller arm.
(indicated as "PULL" on it) of the
receipt side to unlock and open the
print roller arm.
3.
Set a paper roll in the paper roll cradle of the receipt side as
per the diagram.
per the diagram.
4.
Feed the end of the paper along with
the paper positioning guides as per
the diagram.
the paper positioning guides as per
the diagram.
5.
While holding down the paper, slowly close the print roller arm
of the receipt side, and push down the "PUSH"-indicated part
of the arm until you hear a click locking the arm. Make sure
securely you push down the center of the wing part of the arm
as per the diagram. The paper will be fed automatically.
of the receipt side, and push down the "PUSH"-indicated part
of the arm until you hear a click locking the arm. Make sure
securely you push down the center of the wing part of the arm
as per the diagram. The paper will be fed automatically.
If the print roller arm is not securely locked, printing
is not done right. If this problem occurs, open the
arm, and close the arm as instructed above.
is not done right. If this problem occurs, open the
arm, and close the arm as instructed above.
To the printer
Incorrect
To the printer
Correct
Print roller arm
(Receipt side)
(Receipt side)
Paper positioning guides
3
Installing Paper Rolls
Correct
Incorrect
Print roller release lever
(Receipt side)
(Receipt side)
A303_1(En) 06.7.22 9:20 AM Page 10
Click on the first or last page to see other XE-A303 (serv.man6) service manuals if exist.