Sharp XE-A217 (serv.man7) User Manual / Operation Manual ▷ View online
121
d
Operator Maintenance
In Case of Power Failure
When power is lost, the register retains its memory contents and all information on sales entries.
• When power failure is encountered in register idle state or during an entry, the register returns to the
• When power failure is encountered in register idle state or during an entry, the register returns to the
normal state of operation after power recovery.
• When power failure is encountered during a printing cycle, the register carries out the correct printing
procedure after power recovery.
In Case of Printer Error
If the printer runs out of paper, the printer will stall, and “PAPER EMPTY” will appear on the display. Key
entries will not be accepted. Referring to “Replacing the Paper Roll” in this chapter, install a new paper roll
in the proper position, then press the
entries will not be accepted. Referring to “Replacing the Paper Roll” in this chapter, install a new paper roll
in the proper position, then press the
L
key. The printer will print the power failure symbol and resume
printing.
If the print roller arm comes up, the printer stalls, and “PAPER EMPTY” will appear on the display. Key
entries will not be accepted. Push down the arm until it is securely locked, then press the
entries will not be accepted. Push down the arm until it is securely locked, then press the
L
key. The
printer will print the power failure symbol and resume printing.
Cautions in Handling the Printer and Recording Paper
■
Cautions in handling the printer
• Avoid the following environments:
Dusty and humid places
Direct sunlight
Iron powder (A permanent magnet and electromagnet are used in this machine.)
Direct sunlight
Iron powder (A permanent magnet and electromagnet are used in this machine.)
• Never pull the paper when the print roller arm is locked. First lift up the arm, and then remove the paper.
• Never touch the surface of the printer head and print roller.
• Never touch the surface of the printer head and print roller.
■
Cautions in handling the recording paper (thermal paper)
• Use only the paper specified by SHARP.
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid places for storage. Avoid direct sunlight.
• The printed text on the paper can discolor under the following conditions:
• Do not unpack the thermal paper until you are ready to use it.
• Avoid heat. The paper will color at around 70°C.
• Avoid dusty and humid places for storage. Avoid direct sunlight.
• The printed text on the paper can discolor under the following conditions:
Exposure to high humidity and temperature
Exposure to the direct sunlight
Contact with glue, thinner or a freshly copied blueprint.
Heat caused by friction from scratching or other such means.
Contact with a rubber eraser or adhesive tape.
Exposure to the direct sunlight
Contact with glue, thinner or a freshly copied blueprint.
Heat caused by friction from scratching or other such means.
Contact with a rubber eraser or adhesive tape.
• Be very careful when handling the thermal paper. If you want to keep a permanent record, copy the printed
text with a photocopier.
122
Installing Batteries
This register displays a low battery warning message “LOW BATTERY” when the batteries are low, and
displays a no battery warning message “NO BATTERY” when batteries are extremely low or batteries are
not installed.
If no batteries are installed, install two new alkaline batteries LR6 (“AA” size) at once. If batteries are already
installed, replace them with new ones as soon as possible. If the AC power cord is disconnected or a power
failure occurs when the batteries are dead or not installed, all the programmed settings will be reset to the
default settings and any data stored in memory will be cleared.
displays a no battery warning message “NO BATTERY” when batteries are extremely low or batteries are
not installed.
If no batteries are installed, install two new alkaline batteries LR6 (“AA” size) at once. If batteries are already
installed, replace them with new ones as soon as possible. If the AC power cord is disconnected or a power
failure occurs when the batteries are dead or not installed, all the programmed settings will be reset to the
default settings and any data stored in memory will be cleared.
NOTE
Improper use of batteries could cause them to burst or leak, which might damage the interior of
the register. Please take the following precautions:
the register. Please take the following precautions:
• Be sure that the positive (+) and negative (-) poles of each battery are oriented properly.
• Never mix batteries of different types.
• Never mix old batteries and new ones.
• Never leave dead batteries in the battery compartment.
• Remove the batteries if you plan not to use the register for long periods.
• Should a battery leak, clean out the battery compartment immediately, taking care not to let the
• Never mix batteries of different types.
• Never mix old batteries and new ones.
• Never leave dead batteries in the battery compartment.
• Remove the batteries if you plan not to use the register for long periods.
• Should a battery leak, clean out the battery compartment immediately, taking care not to let the
battery fluid come into direct contact with your skin.
• If an incorrect battery is used, it may explode or leak.
• For battery disposal, follow the relevant law or regulation in your country.
• For battery disposal, follow the relevant law or regulation in your country.
Replacement
1.
Be sure the register is plugged in.
2.
Remove the printer cover.
3.
Open the battery cover and remove the old batteries.
123
4.
Install two new LR6(“AA” size) batteries into the battery
compartment.
5.
Close the battery cover.
6.
Replace the printer cover.
124
Replacing the Paper Roll
■
Recording paper specifications
Be sure to use paper rolls specified by SHARP.
The use of any other paper rolls than specified could cause paper jamming, resulting in register malfunction.
The use of any other paper rolls than specified could cause paper jamming, resulting in register malfunction.
Paper specification
Paper width:
57.5 ± 0.5 mm
Max. outside diameter: 80 mm
Quality:
Quality:
High quality(0.06 to 0.08 mm thickness)
• Be sure to set a paper roll prior to using your machine, otherwise it may cause a malfunction.
Install the paper roll in the printer. Be careful then to set the roll and cut the paper end correctly.
To the printer
Incorrect
To the printer
Correct
Correct
Incorrect
(How to set the paper roll)
(How to cut the paper end)
■
Installing the Paper Roll
Always install the paper roll even when you set the register for not printing receipt in REG mode.
1.
Remove the printer cover.
2.
Lift up the print roller arm.
3.
Set the paper correctly in the paper roll cradle.
NOTE
Before placing a new paper roll in the paper
roll cradle, cut off the pasted (taped) part of the
paper and confirm that the cut end of the paper is
straight.
roll cradle, cut off the pasted (taped) part of the
paper and confirm that the cut end of the paper is
straight.
Print roller arm
Click on the first or last page to see other XE-A217 (serv.man7) service manuals if exist.