Sharp DV-NC100H Service Manual ▷ View online
1-10-7
H9741TS
FLOW CHART NO.8
Audio is not outputted.
Set the disc on the disc tray, and playback.
Are the analog audio signals outputted to each pin
of CN1601 on Main CBA?
of CN1601 on Main CBA?
Is the "H" level mute signals outputted to CN1601
on the Main CBA ?
on the Main CBA ?
CN1601 14PIN AUDIO-L
CN1601 16PIN AUDIO-R
CN1601 16PIN AUDIO-R
CN1601 13PIN DVD-A-MUTE
CN1601 15PIN DVD-A(R)-MUTE
CN1601 15PIN DVD-A(R)-MUTE
IC1201 7PIN AUDIO-L
IC1201 1PIN AUDIO-R
IC1201 1PIN AUDIO-R
IC1201 6PIN AUDIO-L
IC1201 2PIN AUDIO-R
IC1201 2PIN AUDIO-R
Replace the DVD Main CBA or the DVD Mechanism.
Replace the DVD Main CBA or the DVD Mechanism.
Replace IC1201.
Check the periphery between Pins(1,7) of IC1201
and JK751, and service it if defective.
and JK751, and service it if defective.
Check each line between each pin of CN1601
and each pin of IC1201 on Main CBA, and service
it if defective.
and each pin of IC1201 on Main CBA, and service
it if defective.
CN1601 14PIN
→
IC1201 6PIN AUDIO-L
CN1601 16PIN
→
IC1201 2PIN AUDIO-R
Are the analog audio signals inputted to each pin
of IC1201.
of IC1201.
Are the analog audio signals outputted to each pin
of IC1201?
of IC1201?
Are the audio signals outputted to the specific
output terminal?
output terminal?
Are the audio signals outputted to the L/R OUT
terminal (JK751)?
terminal (JK751)?
Are the audio signals outputted to Pins(1, 3) of
JK101 (Scart jack)?
JK101 (Scart jack)?
Yes
Yes
Yes
No
No
Yes
No
No
No
No
No
Are the audio signals outputted to Pin(14,15) of
IC751?
IC751?
No
Replace IC501.
Replace IC751.
Check the line between Pin(14,15) of IC751 and JK101,
and their periphery, and service it if defective.
and their periphery, and service it if defective.
Are the "H" pulse inputted into Pins(9,10,11) of IC751?
Yes
Yes
1-10-8
H9741TS
3. VCR Section
Yes
Yes
No
No
FLOW CHART NO.1
FLOW CHART NO.2
The key operation is not functioning.
Are the contact point and the installation state of
the key switches normal?
the key switches normal?
Is the control voltage normally inputted into
Pins(7,8) of IC501?
Pins(7,8) of IC501?
Re-install some key switches correctly or
replace some key switches.
replace some key switches.
Check the key switches and their periphery, and
service it if defective.
service it if defective.
Replace IC501.
0.51
0.92
1.27
1.61
1.98
2.39
2.90
3.60
4.30
-----
-----
-----
-----
S-INH
FF
REW
-----
-----
-----
-----
CH UP
OUTPUT
SELECT
STOP
/EJECT
PLAY
CH
DOWN
DOWN
POWER
REC/OTR
Terminal voltage of IC501-7,8
KEY-1
IC501-7
KEY-2
IC501-8
(V)
Replace the RM2001 (remote control receiver).
Replace remote control unit if need.
Replace remote control unit if need.
Check the line between the RM2001 (remote
control receiver) and the Pin(14) of IC501, and
service it if defective.
control receiver) and the Pin(14) of IC501, and
service it if defective.
Replace IC501.
Is the "L" pulse sent out from Pin(1) terminal of
the RM2001 (remote control receiver) when the
remote control unit is activated?
the RM2001 (remote control receiver) when the
remote control unit is activated?
Is the "L" pulse signal supplied to the Pin(14) of
IC501?
IC501?
Yes
Is 5V voltage supplied to the Pin(3) terminal of
the RM2001 (remote control receiver)?
the RM2001 (remote control receiver)?
Yes
Yes
No
Check AL+5V line and service it if defective.
No
No
No VCR operation is possible from the remote control unit. (Operation is possible from the unit.)
1-10-9
H9741TS
FLOW CHART NO.3
FLOW CHART NO.4
Cassette tape can not be loaded.
Cassette tape is ejected right after the loading.
FLOW CHART NO.5
Cassette tape can not be ejected.
When loading a cassette tape, on Pin(10) of
IC501, does the "L" pulse switch to the "H" pulse?
IC501, does the "L" pulse switch to the "H" pulse?
When loading a cassette tape, on Pin(10) of IC501,
does the "L" pulse switch to the "H" pulse?
does the "L" pulse switch to the "H" pulse?
When loading a cassette tape, on Pin(4) of IC501,
does the "L" pulse switch to the "H" pulse?
does the "L" pulse switch to the "H" pulse?
When pressing the eject button, does the Capstan
Motor start rotating?
Motor start rotating?
Refer to "FLOW CHART NO.6 " <The Capstan
Motor does not rotate>.
Motor does not rotate>.
Check the Reel Disc or Reel Drive Unit, and
service it if defective.
service it if defective.
Replace IC501.
Replace the Capstan Motor unit.
Replace the Loading Motor unit.
While the Capstan Motor is rotating, is the Takeup
Reel rotating?
Reel rotating?
Is the Loading Motor rotating?
Check the Cassette Cam or Cassette Gear, etc,
and service it if defective.
and service it if defective.
While the Takeup Reel is rotating, is the reel pulse
signal inputted to Pin(80) of IC501?
signal inputted to Pin(80) of IC501?
While the reel pulse signal is inputting, is "L" pulse
outputted to Pin(81) of IC501?
outputted to Pin(81) of IC501?
Is the specified voltage (approximately 13V)
outputted to the terminal of the Lading Motor Unit?
outputted to the terminal of the Lading Motor Unit?
When loading a cassette tape, does the LD-SW
operate normally?
operate normally?
When loading a cassette tape, is the specified
voltage (approximately 13V) outputted to the
terminal of the Loading Motor Unit?
voltage (approximately 13V) outputted to the
terminal of the Loading Motor Unit?
Check the line between the start sensor and
Pin(10) of IC501, and service it if defective.
Pin(10) of IC501, and service it if defective.
Replace the Capstan Motor Unit.
Replace the Loading Motor Unit.
Replace IC501.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Check the line between the start sensor and
Pin(10) of IC501, and service it if defective.
Pin(10) of IC501, and service it if defective.
Check the line between the end sensor and
Pin(4) of IC501, and service it if defective.
Pin(4) of IC501, and service it if defective.
Check the line between the LD-SW(SW507) and
Pin(9) of IC501, and service it if defective.
Pin(9) of IC501, and service it if defective.
Check the line between the Takeup Reel sensor
and Pin(80) of IC501, and service it if defective.
and Pin(80) of IC501, and service it if defective.
No
No
No
No
No
No
No
No
No
No
1-10-10
H9741TS
D-FG
D-PG
5Vp-p
2.5Vp-p
FLOW CHART NO.6
Capstan Motor does not rotate.
FLOW CHART NO.7
Drum Motor does not rotate.
FLOW CHART NO.8
Drum Motor rotates only for a few seconds.
FLOW CHART NO.9
RF-SW signal is not outputted.
Is the Drum Motor rotating?
Is 5V voltage supplied to Pin(2) of CN502?
Is 12V voltage supplied to Pin(1,11) of CN502?
Replace the Capstan Motor Unit.
Is over approximately 2.6V voltage supplied to
Pin(5) of CN502?
Pin(5) of CN502?
Check the P-ON+5V line and service it if defective.
Check the line between Pin(5) of CN502 and
Pin(76) of IC501, and service it if defective.
Pin(76) of IC501, and service it if defective.
Check the AL+12V line and service it if defective.
Check the AL+12V line and service it if defective.
Check the AL+12V line and service it if defective.
Check the P-ON+5V line and service it if defective.
Check the line between Pin(8) of CN502 and
Pin(77) of IC501, and service it if defective.
Pin(77) of IC501, and service it if defective.
Replace IC501.
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
Is 5V voltage supplied to Pin(2) of CN502?
Is the drum PG/FG signal inputted to Pin(90) of IC501?
Is the drum PG/FG signal inputted to Pin(90) of IC501?
Is 12V voltage supplied at Pin(1,11) of CN502?
Is the RF-SW signal outputted to Pin(18) of IC501?
Is 12V voltage supplied Pin(1,11) of CN 502?
Replace the Capstan Motor Unit or Cylinder
Assembly.
Assembly.
Replace the Capstan Motor Unit or the Cylinder
Assembly.
Assembly.
Replace the Capstan Motor Unit or the Cylinder
Assembly.
Assembly.
Replace the Capstan Motor Unit or the Cylinder
Assembly.
Assembly.
Refer to "FLOW CHART NO.7" <Drum Motor does
not rotate> and "FLOW CHART NO.8" <Drum
Motor rotates only for a few seconds>.
not rotate> and "FLOW CHART NO.8" <Drum
Motor rotates only for a few seconds>.
Is over approximately 2.6V voltage supplied to
Pin(8) of CN502?
Pin(8) of CN502?
Yes
Yes
Yes
Yes
Replace IC501.
Yes
Yes
Yes
Yes
Click on the first or last page to see other DV-NC100H service manuals if exist.