Sharp DV-NC100H Service Manual ▷ View online
1-10-3
H9741TS
Yes
Yes
Yes
Yes
No
No
No
No
FLOW CHART NO.14
DVD-P-ON+12V is not outputted. (AL+12V is outputted normally.)
FLOW CHART NO.11
Replace Q1053.
No
Yes
Is the "L" pulse (approximately 0V) outputted to
the collector of Q1054?
the collector of Q1054?
Check Q1054 and PWRCON line, and service it if
defective.
defective.
FLOW CHART NO.13
DVD-P-ON+3.3V is not outputted. (EV+3.3V is outputted normally.)
Is the "H" pulse (approximately 4V) inputted to
the base of Q1052?
the base of Q1052?
Replace Q1052.
See FLOW CHART NO.11. <DVD-P-ON+12V is
not outputted. >
not outputted. >
Yes
No
FLOW CHART NO.12
DVD-P-ON+5V is not outputted. (AL+5V is outputted normally.)
Is the "H" pulse (approximately 6V) inputted to
the base of Q1055?
the base of Q1055?
Replace Q1055.
See FLOW CHART NO.11. <DVD-P-ON+12V is
not outputted. >
not outputted. >
Yes
No
The fluorescent display tube does not light up.
Is 3.3V voltage supplied to Pin(6, 24) of IC612?
Is approximately -24V to -28V voltage supplied to
Pin(15) of IC612?
Pin(15) of IC612?
Is there approximately 500kHz oscillation to
Pin(26) of IC612?
Pin(26) of IC612?
Are the filament voltage applied between (1, 2)
and (29, 30) of the fluorescent display tube?
Also negative voltage applied between these pins
and GND?
and (29, 30) of the fluorescent display tube?
Also negative voltage applied between these pins
and GND?
Replace the fluorescent display tube (IC611).
Check the EV+3.3V line and service it if defective.
Check the -FL line and service it if defective.
Check R618, IC612 and their periphery, and
service it if defective.
service it if defective.
Check the power circuit, D1016, D1017,
R1040, C1018 and their periphery, and
service it if defective.
R1040, C1018 and their periphery, and
service it if defective.
1-10-4
H9741TS
2. DVD Section
Yes
No
FLOW CHART NO.1
The key operation is not functioning.
Are the contact point and the installation state of
the key switches (SW2020, SW2021, SW2022) normal?
the key switches (SW2020, SW2021, SW2022) normal?
When pressing each key switches (SW2020,
SW2021, SW2022), do the voltage of each pin
of CL1051 (shown below) change to "H" (3.3V)
from "L" (0V)?
SW2020
SW2021, SW2022), do the voltage of each pin
of CL1051 (shown below) change to "H" (3.3V)
from "L" (0V)?
SW2020
→
CL1051 24PIN
SW2021
→
CL1051 26PIN
SW2022
→
CL1051 25PIN
Check the key switches (SW2020, SW2021,
SW2022) and their periphery, and service it if
defective.
SW2022) and their periphery, and service it if
defective.
No
Re-install the key switches (SW2020, SW2021,
SW2022) correctly or replace the poor switch.
SW2022) correctly or replace the poor switch.
FLOW CHART NO.2
No DVD operation is possible from the remote control unit. (Operation is possible from the unit.)
Replace the RM2001 (remote control receiver).
Replace remote control unit if needed.
Replace remote control unit if needed.
Check the line between the RM2001 (remote
control receiver) and Pin(22) of CL1051, and
service it if defective.
control receiver) and Pin(22) of CL1051, and
service it if defective.
Is the "L" pulse sent out from Pin(1) terminal of the
RM2001 (remote control receiver) when the remote
control unit is activated?
RM2001 (remote control receiver) when the remote
control unit is activated?
Is the "L" pulse signal supplied to Pin(22) of
CL1051?
CL1051?
Replace the DVD Main CBA.
Yes
Yes
Replace DVD Main CBA.
Yes
Yes
Is 5V voltage supplied to Pin(3) terminal of the
RM2001 (remote control receiver)?
RM2001 (remote control receiver)?
Yes
No
Check AL+5V line, and service it if defective.
No
No
FLOW CHART NO.3
The disc tray cannot be opened and closed. (It can be done using the remote control unit.)
Does the voltage of Pin(24) on CL1051 become
3.3V when pressing "OPEN/CLOSE" button on
the unit?
3.3V when pressing "OPEN/CLOSE" button on
the unit?
Refer to "FLOW CHAR NO.4" <The disc tray
cannot be opened and closed.>
cannot be opened and closed.>
Replace the "OPEN/CLOSE" button (SW2020).
No
Yes
FLOW CHART NO.4
The disc tray cannot be opened and closed. (It can not be done using the unit and the remote control unit.)
Replace the DVD Main CBA.
Original DVD Main CBA is poor.
Replace the DVD Mechanism.
No improvement can be found.
No
1-10-5
H9741TS
FLOW CHART NO.5
The [No Disc] indication.
Yes
Replace the DVD Main CBA.
Original DVD Main CBA is poor.
Replace the DVD Mechanism.
No improvement can be found.
No
FLOW CHART NO.6
Both picture and sound do not operate normally.
Both picture and sound do not operate normally.
Yes
Replace the DVD Main CBA.
Original DVD Main CBA is poor.
Replace the DVD Mechanism.
No improvement can be found.
No
1-10-6
H9741TS
FLOW CHART NO.7
Picture does not appear normally.
Set the disc on the disc tray, and playback.
Are the video signals outputted to each pin of
CN1601 on the Main CBA?
CN1601 on the Main CBA?
Replace the DVD Main CBA or the DVD
Mechanism.
Mechanism.
Check the line between each pin of CN1601 and
each pin of IC1403 and IC102 on the Main CBA,
and service it if defective.
each pin of IC1403 and IC102 on the Main CBA,
and service it if defective.
Is 5V voltage supplied to the Pin(4) of IC1403?
Replace IC1403.
Replace IC102.
Check DVD-P-ON+5V line
and service it if defective.
and service it if defective.
Check AL+5V line
and service it if defective.
and service it if defective.
Check the periphery of JK101 from Pins (10, 11,
15) of IC102 and service it if defective.
15) of IC102 and service it if defective.
Check the periphery of JK1401 from
Pin (5) of IC1403 and service it if defective.
Pin (5) of IC1403 and service it if defective.
Check the periphery of JK1401 from
Pin (7) of IC1403 and service it if defective.
Pin (7) of IC1403 and service it if defective.
Are the composite video signals outputted to
Pin(4) of IC751?
Pin(4) of IC751?
CN1601 1PIN
→
IC1403 3PIN S-Y
CN1601 10PIN
→
IC1403 1PIN S-C
CN1601 4PIN
→
IC102 8PIN R
CN1601 8PIN
→
IC102 6PIN G
CN1601 6PIN
→
IC102 1PIN B
Are the video signals shown above inputted into
each pin of IC1403 and IC102?
each pin of IC1403 and IC102?
Are the video signals outputted to each pin
of IC1403 and IC102?
of IC1403 and IC102?
Are the video signals outputted to the specific
output terminal?
output terminal?
Are the RGB video signals outputted to the
Scart jack (JK101)?
Scart jack (JK101)?
Are the luminance signals outputted to the
S-OUT terminal (JK1401)?
S-OUT terminal (JK1401)?
Are the chroma signals outputted to the
S-OUT terminal (JK1401)?
S-OUT terminal (JK1401)?
Yes
Yes
Yes
No
No
No
Is 5V voltage supplied to the Pin(4,12) of IC102?
No
No
Yes
No
Yes
No
No
No
CN1601 1PIN S-Y
CN1601 10PIN S-C
CN1601 4PIN R
CN1601 8PIN G
CN1601 6PIN B
CN1601 10PIN S-C
CN1601 4PIN R
CN1601 8PIN G
CN1601 6PIN B
IC1403 3PIN S-Y
IC1403 1PIN S-C
IC102 8PIN R
IC102 6PIN G
IC102 1PIN B
IC1403 1PIN S-C
IC102 8PIN R
IC102 6PIN G
IC102 1PIN B
IC1403 6PIN CVBS
IC1403 5PIN S-Y
IC1403 7PIN S-C
IC1403 5PIN S-Y
IC1403 7PIN S-C
IC102 10PIN R
IC102 11PIN G
IC102 15PIN B
IC102 11PIN G
IC102 15PIN B
Replace IC751.
Replace IC501.
Are the composite video signals outputted to
Pin(19) of JK101 (Scart jack)?
Pin(19) of JK101 (Scart jack)?
Check the line between Pin(4) of IC751 and JK101
and service it if defective.
and service it if defective.
Are the "H" pulse inputted into Pins(9,10,11) of IC751?
No
Yes
Yes
No
No
Click on the first or last page to see other DV-NC100H service manuals if exist.