Sharp XL-MP35H (serv.man10) Service Manual ▷ View online
XL-MP35H
– 6 –
TAPE MECHANISM SECTION
Perform steps 1 to 5 and 8 of the disassembly method to
remove the tape mechanism. (See page 5.)
remove the tape mechanism. (See page 5.)
How to remove the record / playback and erase
heads (See Fig. 6-3.)
heads (See Fig. 6-3.)
1. Remove the screws (A1) x 2 pcs., to remove the erase
head.
2. Remove the screws (A2) x 2 pcs., to remove the record/
playback head.
Note:
After replacing the heads and performing the azimuth
adjustment, be sure to apply screwlock.
After replacing the heads and performing the azimuth
adjustment, be sure to apply screwlock.
How to remove the pinch roller (See Fig. 6-4.)
1. Carefully bend the pinch roller pawl in the direction of the
arrow
<A>
, and remove the pinch roller (B1) x 1 pc.,
upwards.
How to remove the belts (See Fig. 6-5.)
1. Remove the main belt (C1) x 1 pc., from the motor pulley.
2. Remove the FF/REW belt (C2) x 1 pc., from the REW/FF
2. Remove the FF/REW belt (C2) x 1 pc., from the REW/FF
roller.
3. Put on the belts in the reverse order of removal.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
Note:
When putting on the belt, ascertain that the belt is not twisted,
and clean it.
How to remove the motor
(See Fig. 6-6.)
(See Fig. 6-6.)
1. Remove the main belt.
2. Remove the screws (D1) x 2 pcs., to remove the motor
2. Remove the screws (D1) x 2 pcs., to remove the motor
bracket.
3. Remove the screws (D2) x 3 pcs., to remove the motor.
Note:
When mounting the motor, pay attention to the motor mounting
angle.
Note:
When mounting the motor, pay attention to the motor mounting
angle.
<A>
Pinch Roller
(B1)x1
(B1)x1
Pinch Roller
Pawl
Pawl
REMOVING AND REINSTALLING THE MAIN PARTS
Main Belt
(C1)x1
(C1)x1
FF/REW Belt
(C2)x1
(C2)x1
REW/FF
Clutch
Clutch
Motor
Erase Head
Record/
Playback Head
Playback Head
(A1)x2
ø2x8mm
ø2x8mm
(A2)x1
ø2x3mm
ø2x3mm
(A2)x1
ø2x7mm
ø2x7mm
(D1)x1
ø2x4mm
ø2x4mm
(D2)x3
Special
Screw
Special
Screw
Motor
Bracket
Bracket
Motor
Motor
(D1)x1
ø2x4mm
ø2x4mm
(K1)x3
ø2.6x10mm
ø2.6x10mm
Top Cabinet
CD Mechanism
(J1)x4
ø2.4x10mm
ø2.4x10mm
(J2)x1
ø2.6x10mm
ø2.6x10mm
(J3)x2
(J3)x1
Top Cabinet
CD PWB
Open/Close
Switch PWB
Switch PWB
CD Mechanism
Figure 6-1
Figure 6-2
Figure 6-3
Figure 6-4
Figure 6-5
Figure 6-6
– 7 –
XL-MP35H
How to remove the tape mechanism PWB
(See Fig. 7-2.)
(See Fig. 7-2.)
1. Remove the screw (F1) x 1 pc., to remove the tape
mechanism PWB.
2. Remove the screws (F2) x 1 pc.
3. Remove the solder joints (F3) x 2 pcs., to remove the tape
3. Remove the solder joints (F3) x 2 pcs., to remove the tape
mechanism PWB.
How to remove the flywheel (See Fig. 7-1.)
1. Remove the belt.
2. Remove the stop washer (E1) x 1 pc., with a small precision
2. Remove the stop washer (E1) x 1 pc., with a small precision
screwdriver to extract the flywheel from the capstan metal.
Note:
When the stop washer is deformed or damaged, replace it
with a new one.
When the stop washer is deformed or damaged, replace it
with a new one.
How to reinstall the parts
Install each part in the reverse order of the removal with care.
Stop
Washer
Washer
Driver
(E1)x1
Stop Washer
Stop Washer
Mechanism
Chassis
Chassis
Washerx2
Flywheel
Tape
Mechanism
PWB
Mechanism
PWB
Tape
Mechanism
PWB
Mechanism
PWB
(F3)x2
Solder
Joint
Solder
Joint
(F2)x1
ø2x8mm
ø2x8mm
(F1)x1
ø2x3mm
ø2x3mm
Figure 7-1
Figure 7-2
Display